Clarke COBS1 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0820 - ISS 4

ORIGINAL INSTRUCTIONS

OSCILLATING BOBBIN SANDER

MODEL NO: COBS1

PART NO: 6462013

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE product.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONTENTS

The following items should be supplied in the carton. If any parts are missing,

do not operate until the missing parts are replaced. Failure to follow this

instruction could result in serious injury.

SAFETY SYMBOLS

1 x Bobbin Sander

1 x 13 mm Ø Sanding Sleeve

1 x 19 mm Ø Sanding Sleeve

1 x 26 mm Ø Sanding Sleeve

1 x 38 mm Ø Sanding Sleeve

1 x 51 mm Ø Sanding Sleeve

1 x 76 mm Ø Sanding Sleeve

1 x 13 mm Ø Table Insert

1 x 19 mm Ø Table Insert

1 x 26 mm Ø Table Insert

1 x 38 mm Ø Table Insert

1 x 51 mm Ø Table Insert

1 x 76 mm Ø Table Insert

1 x 19 mm (Ø) x 115 mm Sanding Bobbin

1 x 26 mm (Ø) x 115 mm Sanding Bobbin

1 x 38 mm (Ø) x 115 mm Sanding Bobbin

1 x 51 mm (Ø) x 115 mm Sanding Bobbin

1 x 76 mm (Ø) x 115 mm Sanding Bobbin

1 x Nut

1 x 15 mm Ø Spindle Washer

1 x 21 mm Ø Spindle Washer

1 x 45.8 mm Ø Spindle Washer

1 x Spanner

1 x Support Washer

Read this instruction

booklet carefully.

Wear ear

protection.

Wear eye

protection.

Wear a dust mask

that is specially

designed to filter

microscopic

particles.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

1. Keep work area clear

• Cluttered areas and benches

invite injuries.

2. Consider work area environment

• Do not expose tools to rain.

• Do not use tools in damp or wet

locations.

• Keep work area well lit.

• Do not use tools in the presence

of flammable liquids or gases.

3. Guard against electric shock

• Avoid body contact with

earthed or grounded surfaces

(e.g. pipes, radiators, ranges,

refrigerators).

4. Keep other persons away

• Do not let persons, especially

children, not involved in the work

touch the tool or the extension

cord and keep them away from

the work area.

5. Store idle tools

• When not in use, tools should be

stored in a dry locked-up place,

out of reach of children.

6. Use protective equipment

• Use safety glasses.

• Use face or dust mask if working

operations create dust.

7. Do not force the tool

• It will do the job better and safer

at the rate for which it was

intended.

8. Use the right tool

• Do not force small tools to do the

job of a heavy duty tool.

• Do not use tools for purposes not

intended; for example do not

use circular saws to cut tree limbs

or logs.

9. Dress properly

• Do not wear loose clothing or

jewellery, they can be caught in

moving parts.

• Non-skid footwear is

recommended when working

outdoors.

• Wear protective hair covering to

contain long hair.

10. Dust extraction equipment

• Ensure dust extraction

equipment is used.

11. Do not abuse the cord

• Never yank the cord to

disconnect it from the socket.

Keep the cord away from heat,

oil and sharp edges.

12. Secure the work

• Where possible use clamps or a

vice to hold the work. It is safer

than using your hand.

WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL

INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/

OR SERIOUS INJURY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

13. Do not overreach

•Keepproperfootingand

balance at all times.

14. Maintain tools with care

• Keep cutting tools sharp and

clean for better and safer

performance.

• Follow instruction for lubricating

and changing accessories.

• Inspect tool cords periodically

and if damaged have them

repaired by an authorized

service facility.

• Inspect extension cords

periodically and replace if

damaged.

• Keep handles dry, clean and

free from oil and grease.

15. Disconnect tools

• When not in use, before servicing

and when changing accessories

such as blades, bits and cutters,

disconnect tools from the power

supply.

16. Remove adjusting keys and

wrenches

• Form the habit of checking to

see that keys and adjusting

wrenches are removed from the

tool before turning it on.

17. Avoid unintentional starting

• Ensure switch is in “off' position

when plugging in.

18. Use outdoor extension leads

• When the tool is used outdoors,

use only extension cords

intended for outdoor use and so

marked.

19. Stay alert

• Watch what you are doing, use

common sense and do not

operate the tool when you are

tired.

20. Check damaged parts

• Before further use of tool, it

should be carefully checked to

determine that it will operate

properly and perform its

intended function.

• Check for alignment of moving

parts, binding of moving parts,

breakage of parts, mounting

and any other conditions that

may affect its operation.

• A guard or other part that is

damaged should be properly

repaired or replaced by an

authorized service centre unless

otherwise indicated in this

instruction manual.

• Have defective switches

replaced by an authorized

service centre.

• Do not use the tool if the switch

does not turn it on and off.

21. Warning

• The use of any accessory or

attachment other than one

recommended in this instruction

manual may present a risk of

personal injury.

22. Have your tool repaired by a

qualified person

• This electric tool complies with

the relevant safety rules. Repairs

should only be carried out by

qualified persons using original

spare parts, otherwise this may

result in considerable danger to

the user.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely, as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug.

• The BLUE wire must be

connected to the

terminal which is

marked N or coloured

black.

• The BROWN wire must

be connected to the

terminal which is

marked L or coloured

red.

AN APPROVED RESIDUAL CURRENT DEVICE (RCD) WHICH HAS A TRIPPING

CURRENT OF LESS THAN 30mA MUST BE USED.

If you are not sure, consult a qualified electrician. DO NOT try to do any repairs

This symbol indicates that this is a Class II product, and does not require

an earth connection.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE

COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

BLUE = NEUTRAL BROWN = LIVE

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

a 5 Amp

the cable is firmly held by the clamp

fuse.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

PARTS IDENTIFICATION

1Table 6Spanner

2 Bobbin 7 Dust Chute

3 Spindle Washer 8 Bobbins + Sanding Sleeves

4Nut 9Spindle

5 Bobbin Sander 10 Table Inserts

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

FITTING THE SANDPAPER SLEEVE ONTO THE BOBBIN

1. Fit the sandpaper sleeve on to the

bobbin as shown.

NOTE: The 13mm sanding sleeve

does not fit onto a bobbin, it

simply slides directly onto the

spindle.

PARTS STORAGE

1. The storage slots on the front are

used to store the table inserts.

2. The storage slots on the rear are

used to store the bobbins/sanding

sleeves and the spanner supplied.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SETUP

1. Put the support washer on the

spindle.

• Grooved side must face up.

2. Slide the bobbin on to the spindle.

3. Secure the bobbin using the

correct washer, and nut supplied.

• Use the largest washer that

does not overlap the edge of

the sanding sleeve.

• Tightening the nut causes the

bobbin to expand slightly

which prevents the sanding

sleeve from sliding off of the

bobbin.

4. Put the correct table insert into

place as shown and tighten up

the nut on top of the bobbin.

• The table insert must be used at

all times. Replacement table

inserts are available from the

Clarke spare parts department.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DUST COLLECTION

Connect a suitable dust collector to

the dust chute.

USING THE SANDER

SWITCH ON

Press the green ON button, and allow

the machine to come up to full

speed before use.

SWITCH OFF

To switch OFF, simply press the red

button.

NOTE: In the event of a power failure

the sander will switch off

automatically. The user will need to press the green ON button again to

restart.

SANDING TIPS

• Do not force the sander, allow it to work at its own pace.

• Keep a firm grip on the workpiece, the sander will have a tendency

to push the workpiece to the right.

WARNING: CONTACT WITH OR INHALATION OF DUST FROM LEAD BASED

PAINTS CAN ENDANGER THE HEALTH OF THE OPERATOR AND

BYSTANDERS, ALWAYS WEAR A SUITABLE DUST MASK WHEN USING THE

SANDER.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Sander Handbücher

Clarke

Clarke Woodworker BS1 Bedienungsanleitung

Clarke

Clarke American 12 Montage- und Wartungsanleitung

Clarke

Clarke Contractor CON180 Installations- und Betriebshandbuch

Clarke

Clarke ALTO C2K Series Bedienungsanleitung

Clarke

Clarke Woodworker CBS1-5 Bedienungsanleitung

Clarke

Clarke X-Pro CAT136 Installations- und Betriebshandbuch

Clarke

Clarke Alto MP-1800 Bedienungsanleitung

Clarke

Clarke WOODWORKER CDS1 Installations- und Betriebshandbuch

Clarke

Clarke EZ Sand Installations- und Benutzerhandbuch

Clarke

Clarke Woodworker CS6-9C Installations- und Betriebshandbuch

Clarke

Clarke l 1600DC Bedienungsanleitung

Clarke

Clarke Super 7R Bedienungsanleitung

Clarke

Clarke 07097A Bedienungsanleitung

Clarke

Clarke 07032C Bedienungsanleitung

Clarke

Clarke C2K 13 Bedienungsanleitung

Clarke

Clarke CBB150 Bedienungsanleitung

Clarke

Clarke Woodworker CBS1-5 Bedienungsanleitung

Clarke

Clarke Air CAT176 Installations- und Betriebshandbuch

Clarke

Clarke Woodworker BS1 Installations- und Betriebshandbuch

Clarke

Clarke CAT111 Installations- und Betriebshandbuch

Clarke

Clarke CFP-130 Bedienungsanleitung

Clarke

Clarke CP254 Installations- und Betriebshandbuch

Clarke

Clarke OBS-18 Bedienungsanleitung

Clarke

Clarke CSR310 Bedienungsanleitung

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Craftsman

Craftsman 351.215131 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung

Parkside

Parkside PEXS 270 Al Bedienungsanleitung

Makita

Makita 9207SPB Bedienungsanleitung