Clarke X-PRO CAT 160 Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0217

PA L M S A N D E R

MODEL NO: CAT160

PART NO: 3120174

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Palm Sander. Before attempting to use

this product, please read this manual thoroughly and follow the instructions

carefully. In doing so you will ensure the safety of yourself and that of others

around you, and you can look forward to your purchase giving you long and

satisfactory service.

SPECIFICATION

Please keep these instructions in a safe place for future reference.

Model Numbers CAT160

Operating Pressure 90 psi (6.2 bar)

Air Consumption @ 6.3 bar 4.5 cfm (2.1L/sec) rated average

14.8 cfm (7.0L/sec) maximum

Air Inlet Size 1/4” BSP female thread

Vibration Level 8.5 m/s2

Uncertainty Factor (K) 1.5

Sound Power Level 98 dB LWA

Sound Pressure Level 87 dBA

Uncertainty Factor (K) 3.0

Dimensions (L x D x H) 220 x 150 x 110 mm (with backing pad

200 x 105 x 98 mm (without backing pad)

Weight 1.1 kg

Max Speed 10,000 rpm

Speed Control Variable

Dust extract hose 1335 long x 21 dia

Sanding pad Hook & Loop 150 mm dia

Thread type M8 x 24TPI

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair

out of the way.

3. Keep children and visitors away - Do not let children handle the tool.

USE OF AIR POWERED TOOLS

1. Stay alert and use common sense - do not operate this tool when you are

tired or under the influence of alcohol, drugs or medication.

2. Always wear eye protectors when using air tools. Eye protectors must

provide protection from flying particles from the front and the side.

3. Do not overreach - keep proper footing and balance at all times.

4. Never use oxygen, CO2, combustible gasses, or any bottled gas, as a

source of power for an air tool. This product should only be used with a

suitably rated compressed air supply.

5. Do not connect the air hose with your finger on the trigger of the tool.

6. Do not fit the air tool to any stand or clamping device that may damage it.

7. Do not exceed the maximum pressure for the tool.

8. Keep the air hose away from heat, oil and sharp edges.

9. Check hoses for leaks or excessive wear before use, and ensure that all

connections are secure.

10. Do not use the tool for any other purpose than described in this manual.

11. Do not carry out any alterations or modifications to the tool.

12. Always disconnect from the air supply when:

• Performing any maintenance.

• The tool is not in use.

• The tool will be left unattended.

13. Never use the tool if it is defective or operating abnormally.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

14. This air tool should be serviced at regular intervals by qualified service

personnel.

15. Avoid damaging the air tool by applying excessive force of any kind.

16. Always maintain the air tool with care. Keep it clean for the best and safest

performance.

17. ALWAYS ensure the workpiece is firmly secured leaving both hands free to

control the tool.

18. ALWAYS ensure the tool has stopped before putting it down after use.

19. ALWAYS ensure that any attachments are correctly fastened before

connecting the tool to the power supply

20. Do not force or misuse the air tool. It will do a better and safer job at the

rate for which it was designed.

21. Quick change couplings should not be located at the tool. They add

weight and could fail due to vibration.

22. Do not remove any labels. Damaged labels should be replaced.

23. This tool vibrates with use. Vibration may be harmful to your hands or arms.

Stop using the tool if discomfort, a tingling feeling or pain occurs. Seek

medical advice before resuming use.

SANDER-SPECIFIC SAFETY RULES

1. Inspect the sanding pad before use. Do not use if cracked or broken.

Check that the rated speed of the backing pad is at least as high as that

of the machine.

2. Avoid contact with the moving sanding pad and wear suitable gloves to

protect the hands.

3. Never start the tool unless the abrasive pad is applied to the workpiece.

4. Beware of potentially explosive atmospheres being caused by dust / fumes

resulting from sanding and use dust extraction systems where possible.

5. Always wear a face mask when using the sander as protection from

airborne particles of sanded material. Avoid disturbing existing dust and

minimise the scattering of dust in the workplace environment. Take steps to

control the dust at the point of emission.

DUST EXTRACTION

The sander is provided with a dust extraction facility. Please note however,

that this does not preclude the user from wearing a face mask to prevent the

inhalation of dust particles.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

It is an EEC requirement that a dust extraction facility be provided on power

tools, however, due to the nature of the tool, some of the dust produced will

be forced into the surrounding atmosphere and will not be collected.

TRANSPORTATION

1. Never carry the tool by the air hose or with your finger on the trigger.

2. When not in use the tool should be disconnected from the air supply and

stored in a dry place out of the reach of children.

IMPORTANT

Please read all of the safety and operating instructions carefully before using

this product. The following safety symbols are to be found on the machine.

Read this instruction

booklet carefully

before use.

Wear ear protection.

Wear eye protection. Wear dust mask.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

The CAT160 Sander is ideal for use in garages and workshops. Random orbit

sanders give a virtually scratch - free finish on various surfaces prior to painting

or varnishing the finished surface.

Your sander should include the items above. Any damage or deficiency

should be reported to your CLARKE dealer immediately.

NO DESCRIPTION NO DESCRIPTION

1 Dust collection tube 6 Speed Control Regulator

2 Sanding Pad 7 Spanner

3 Trigger 8 1/4” BSP male connector

4 Waste Outlet 9 Dust Bag

5 1/4” BSP Air Inlet Connection

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

• Use only clean, dry, regulated compressed air as a power source.

• Air compressors used with the tool must comply with the appropriate

European Community Safety Directives.

• A build-up of moisture or oil in the air compressor will accelerate

wear and corrosion in the tool. ensure any moisture is drained from

the compressor daily and the inlet filter is kept clean.

• If an unusually long air hose is required, (over 8 metres), the line

pressure or the hose inside diameter may need to be increased.

• The air hose must be rated at least 150% of the maximum operating

pressure of the tool.

• A typical air line layout is shown above. If an automatic in-line filter/

regulator is used, it will keep the tool in good condition but should be

regularly checked & topped up with oil. Clarke air-line oil should be

used, and the lubricator adjusted to approx 2 drops per minute.

• Never exceed the maximum operating pressure for the tool. Higher

pressures and unclean air will shorten the life of the tool due to faster

wear and is a possible safety hazard.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

FITTING A SANDING DISC

1. Select the disc to be used which

MUST be 150mm diameter with

hook and loop backing.

2. Line up the holes in the disc with

those on the sanding pad. (This is

necessary for dust extraction

purposes). Press the disc firmly onto

the pad to secure it.

CONNECTING THE AIR SUPPLY

Ensure the compressor is turned off and that the trigger is NOT depressed when

connecting the air line to avoid inadvertent starting of the sander.

1. Remove the protective plug from

the air inlet and connect a suitable

hose with a male end fitting or use

the adaptor supplied to connect a

suitable hose.

2. Connect the other end of the hose

to the compressed air supply.

3. Turn on the air supply and check

for air leaks. Rectify any found

before proceeding.

• PTFE tape may be useful for sealing threaded connections.

4. If required, connect an in-line mini oiler to the tool. A mini oiler helps to

prolong the life of the air tool.

5. If a mini-oiler is not being used, run a few drops of oil through the tool

before use. It can be entered through the air inlet or via the hose at the

nearest connection to the air supply.

6. A gauze filter is fitted within the air inlet. Ensure this filter is always kept

clean. An airline can be connected to the adapter, via a quick release

coupling (not supplied).

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR

COMPRESSORS AND A COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CONNECTING THE DUST COLLECTION TUBE & BAG

1. Push the dust collection tube onto

the waste outlet.

2. Use the string to tie the dust

collecting bag onto the smaller

end of the tube.

3. The dust bag should be emptied

regularly:- do not wait until it is

completely full. Gently pull open

the velcro flap across the end of

the bag to empty the contents

into your bin.

Your sander is now ready for use. Alternatively, vacuum extract can be used.

OPERATION

IMPORTANT: Only use abrasive sanding pads designed for use with this type

of 150mm dia sanding pad (rated at over 10000rpm).

1. Squeeze the trigger against the

body of the tool to start.

• Use the speed regulator to set

the speed.

• Move the regulator lever

forwards for maximum speed

and back to slow down.

2. Rest the sander on the workpiece

before starting it. Let the sander do

the work.

• The actual weight of the sander is normally sufficient for efficient

sanding. Do not put additional pressure on the sander which would

only slow down the speed of the pad, reducing efficiency and

placing an additional burden on the motor.

3. Pass the sander back and forth in wide, overlapping areas, taking care to

keep the sander moving around at all times. Avoid dwelling in one place

for more than a moment.

4. Release the trigger to stop the sander.

5. Always ensure the sander has stopped before putting it down.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DISCONNECTING THE AIR SUPPLY

1. Do not disconnect the air supply hose until the compressor has been shut

down and the compressed air released.

2. Squeeze the trigger to discharge any compressed air from the sander and

air hose.

3. Once the pressure has been released, disconnect the air supply hose from

the sander.

MAINTENANCE

Please note that factors other than the tools condition may effect its operation

and efficiency, such as reduced compressor output, excessive drain on the

airline, moisture or restrictions in the air-line, or the use of connectors of

improper size or poor condition which will reduce air supply.

DAILY

1. Before use, drain water from the air-line and compressor.

2. Lubricate the air tool daily for optimum performance, using a high quality

airline oil either via a lubricator in the air supply system or by placing a few

drops into the air inlet immediately before use. This should be carried out

regardless of whether or not an in-line lubricator is used.

CLEANING

1. Keep the sander clean and free from debris.

2. Grit or gum deposits in the mechanism may eventually reduce efficiency.

This condition can be corrected by cleaning the air inlet filter and flushing

out the tool with gum solvent oil or an equal mixture of SAE No10 oil and

paraffin.

3. Failing this, the tool should be disassembled, thoroughly cleaned, dried

and reassembled. You may prefer to take the tool to your CLARKE dealer if

internal maintenance is required.

4. If the sander becomes sluggish and the air supply is of good quality, it may

be necessary to replace worn or damaged parts. You may prefer to take

the tool to your Clarke dealer if internal maintenance is required.

WARNING: MAKE SURE THAT THE AIR TOOL IS DISCONNECTED FROM THE

AIR SUPPLY BEFORE STARTING ANY CLEANING OR MAINTENANCE

PROCEDURES.

Inhaltsverzeichnis

Andere Clarke Sander Handbücher

Clarke

Clarke CMS 200 Bedienungsanleitung

Clarke

Clarke CS4-6E Bedienungsanleitung

Clarke

Clarke Air CAT176 Installations- und Betriebshandbuch

Clarke

Clarke CDS1V Bedienungsanleitung

Clarke

Clarke RS-16 HDTR Bedienungsanleitung

Clarke

Clarke 07097A Bedienungsanleitung

Clarke

Clarke CAT38 Bedienungsanleitung

Clarke

Clarke OBS-18DC Bedienungsanleitung

Clarke

Clarke American 8 07105A Bedienungsanleitung

Clarke

Clarke Woodworker BS1 Bedienungsanleitung

Clarke

Clarke DU-8R Bedienungsanleitung

Clarke

Clarke OBS-18 Bedienungsanleitung

Clarke

Clarke CBB150 Bedienungsanleitung

Clarke

Clarke CBB200 Bedienungsanleitung

Clarke

Clarke RS-16 HDTR Bedienungsanleitung

Clarke

Clarke 01207SD Bedienungsanleitung

Clarke

Clarke CBK100C Bedienungsanleitung

Clarke

Clarke DWS180 Bedienungsanleitung

Clarke

Clarke Super 7R Edger 07013A Bedienungsanleitung

Clarke

Clarke American Sanders B2 Bedienungsanleitung

Clarke

Clarke 07100A Bedienungsanleitung

Clarke

Clarke 07101B Bedienungsanleitung

Clarke

Clarke RS-16 HDTR Installations- und Betriebsanleitung

Clarke

Clarke X-Pro CAT136 Installations- und Betriebshandbuch

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung

Parkside

Parkside PEXS 270 Al Bedienungsanleitung

Makita

Makita 9207SPB Bedienungsanleitung

Flex

Flex ST 1005 VE Bedienungsanleitung