Clarke Woodworker MBS600C Bedienungsanleitung

ASSEMBLY INSTRUCTIONS

GC0311

COMPOUND MITRE SAW

MODEL NO: MBS600C

Part No: 6461512

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Mitre Saw.

Before attempting to use the product, it is essential that you read this manual

thoroughly and carefully follow all instructions given. In doing so you will

ensure the safety of yourself and that of others around you, and you can also

look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of

12 months from the date of purchase. Please keep your receipt as proof of

purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission. This guarantee does not effect

your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All tools,

accessories and packaging should be sorted, taken to a re-cycling centre

and disposed of appropriately.

SERVICING

For parts & servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

Parts & Service: 020 8988 7400/E-mail: Part[email protected] or [email protected]

COMPONENT GUIDE

FIG 1

Upon receipt of the product, unpack all loose components and check for

any missing parts. Any identified should be reported to your Clarke dealer.

The MBS600C includes the following:

1 x Saw Frame c/w Blade

1 x Mitre Table

2 x Base Plates

1 x Angle Carriage

4 x Support Rods

1 x Work Clamp

1 x Work Stop

1 x Fixings Pack containing: Pointer & screw,

Pivot Pin,

4 x screws/washers,

4 x Depth Stop Collars.

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

ASSEMBLY

BASE PLATES

Attach the Base Plates to the Mitre Table

using the socket head screws and flat

washers provided - two for each base.

• A 3mm hex key is required.

• The two holes nearer the edge of the

base should be towards the outside

of the Mitre Table and are visible

when assembled as shown in Fig 2.

• These holes may be used to fix the

Mitre Saw to a workbench for

additional stability (see Mounting).

MITRE TABLE

Attach the Angle Carriage to the Mitre

Table. Line up the pivot hole in the angle

carriage with the hole in the Mitre Table

and insert the pivot pin from below as

shown in Fig 3. Lift the locking lever,

depressing the locking pin so that the

angle carriage and table can connect.

• The pivot pin is a tight fit so it may be

necessary to turn the table over and

tap it home with a small hammer.

Screw in the two locating screws as shown in Fig 3, and tighten

with a 3mm hex key allowing the carriage to move freely on the pin,

but without any slop between the carriage and the table.

Attach the Pointer to the carriage with the screw provided as shown in Fig 3.

WORK CLAMP

Screw the Work Clamp support into one

of the threaded holes in the front face of

the Mitre Table, (see fig 4), depending

upon which side of the saw blade your

work is to be mounted.

Secure the Work Clamp support with the

locking nut.

FIG 2

FIG 3

FIG 4

Parts & Service: 020 8988 7400/E-mail: Part[email protected] or [email protected]

GUIDE RODS, SAW FRAME AND BLADE

Insert the Guide Support Rods into the holes in each angle setting quadrant

as shown in Fig. 5 and secure using the x-head screws.

Slide a Depth Stop Collar onto either

one of the Guide Support Rods at each

end of the carriage, before carefully

sliding the guides of the Saw Frame

Assembly onto the Guide Support Rods.

With the Saw Frame assembly in

position, tension the blade using the

wing nut, until any sideways deflection

of the blade is minimal.

• This is essential to ensure a straight

and repeatable cut from the blade.

WORK- STOP

Screw the Stop Support Rod into the

threaded hole at one end of the Mitre

Table depending upon which side of

the saw blade your work is to be

mounted.

Position the stop pad close to the table

surface and lock the rod in place with

the locking nut as shown in Fig 6.

• Your Mitre Saw is now fully

assembled and ready for use.

MOUNTING

You may wish to install the Mitre Saw on a firm foundation such as a

workbench or work table. This is particularly advisable if you are cutting larger

workpieces.

Use the holes in the Base Plates for this purpose, securing with bolts, flat

washers and wing nuts for quick and easy removal, if required (not supplied).

FIG 5

FIG 6

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

USING THE MITRE SAW

CUTTING SIMPLE MITRES OR BEVELS

Simple mitres or bevels are cuts made in one plane only. For simple mitres, the

carriage is moved to the desired angle to the base by lifting the Locking

Lever to allow the carriage to swivel, with the saw blade remaining

perpendicular to the table.

Setting the Carriage to the angles shown in Fig 7, will produce the mitres

illustrated. The angle is shown by the pointer.

COMPOUND MITRES

For compound mitres the saw frame is

tilted over at an angle to the table. This

is done by removing the Locking Pin

and slackening off the Quadrant

Locking Wingnuts sufficiently to free the

Quadrant and to allow the Saw Frame

to be tilted to the desired angle. The

locking pin is then replaced and the

wingnuts re tightened (Fig 8), when the

Saw Frame is set at the desired angle.

Compound mitres are therefore cut

using a combination of these settings.

CUTTING TECHNIQUE

When cutting, DO NOT force the saw blade, as this will lead to blade

distortion and inaccurate mitres/bevels. Only a very gentle pressure is

required. Let the saw do the work.

Ensure the Locking Pin is in place and the Quadrant Locking Wingnuts at both

ends of the carriage are tight before use.

FIG 7

FIG 8

Parts & Service: 020 8988 7400/E-mail: Part[email protected] or [email protected]

Ensure the saw blade is correctly tensioned before use - too slack will allow

the blade to twist, producing inaccurate mitres.

Use the Depth Stop Collars as required when making either a horizontal or

sloping cut. Tighten them securely with the thumbscrews before cutting.

MAINTENANCE

Should the rotating movement of the quadrants become sticky, unscrew the

keep-plate of each quadrant to allow its removal.

Pull the quadrant forward and capture

the ball and spring which will fall out,

Clean the castings of any sawdust and

apply a light coating of general purpose

grease to the quadrant mating surfaces

before re-assembly.

• Note that the ball and spring can be

re-fitted either from below, or from

above, through the grub screw hole

shown in Fig 9. The spring tension can

be adjusted by tightening the grub

screw with a hex key.

Replacement Blades are available from your CLARKE dealer;

Part No: 6470175

SPECIFICATIONS

erutaeF noitacificepS

htdiWesaBmm584

htgneLelbaTmm004

htgneLedalBwaSmm006

htpeDedalBwaSmm54

thgieWgk0.4

tuCfohtpeDxaMmm02

09@tuCfohtdiWxaM

mm09

hcnIrephteeTipt41

Please note that the details and specifications contained herein, are correct at the

time of going to print. However, CLARKE International reserve the right to change

specifications at any time without prior notice.

FIG 9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Gesehen Handbücher

Clarke

Clarke CPS85 Bedienungsanleitung

Clarke

Clarke CCO14B Bedienungsanleitung

Clarke

Clarke CSS 300 Betriebsanleitung

Clarke

Clarke CLS405 Kurzanleitung

Clarke

Clarke CONTRACTOR CON850B Bedienungsanleitung

Clarke

Clarke CONTRACTOR CON185B Bedienungsanleitung

Clarke

Clarke METALWORKER CBS 7MC Installations- und Betriebshandbuch

Clarke

Clarke CRS350M Bedienungsanleitung

Clarke

Clarke CMS 200 Installations- und Betriebshandbuch

Clarke

Clarke CLS400 Installations- und Betriebshandbuch

Clarke

Clarke CBS7MB Installations- und Betriebshandbuch

Clarke

Clarke WOODWORKER CBS250 Handbuch

Clarke

Clarke CMS255S Bedienungsanleitung

Clarke

Clarke Metalworker CBS45MD Bedienungsanleitung

Clarke

Clarke CT4014 Bedienungsanleitung

Clarke

Clarke Woodworker MBS550A Bedienungsanleitung

Clarke

Clarke CMS216S Bedienungsanleitung

Clarke

Clarke CTS16 Installations- und Betriebshandbuch

Clarke

Clarke CSS400D Bedienungsanleitung

Clarke

Clarke CCS305 Installations- und Betriebshandbuch

Clarke

Clarke CRS710V Bedienungsanleitung

Clarke

Clarke CON14 Bedienungsanleitung

Clarke

Clarke CMS10S2 Bedienungsanleitung

Clarke

Clarke CBS 190 Installations- und Betriebshandbuch

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Altrad

Altrad BELLE RANGER 450 Bedienungsanleitung

Porter-Cable

Porter-Cable 725 Bedienungsanleitung