Clarke CHT718 Bedienungsanleitung

USER INSTRUCTIONS

GC06/12

UNIVERSAL HUB/BEARING

PULLER

Model No: CHT718

Part No: 1801718

2

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE product. The kit may be used for

installing seals and bearings into the hubs of most vehicles. It may also be

used for pulling hubs where the wheel flange is drilled and tapped so that the

road wheel is secured with bolts.

Please read and follow the instructions carefully. In doing so you will ensure

the safety of yourself and others around you, and you can look forward to

the product giving you long & satisfactory service.

Please keep these instructions in a safe place for future reference

KIT CONTENTS

A Sleeve 76mm (3”) HTCHT71810

B1 Cup- 86mm (3-13/32”) HTCHT71811

B2 Cup- 91mm (3-19/32”) HTCHT71812

C1 Bolt M14 x 90 HTCHT71813

D Flat Washer HTCHT71814

E Sleeve 36mm (1-7/16”) HTCHT71815

F Centre Bolt HTCHT71816

G Thrust Washers HTCHT71817

H Long Nut HTCHT71818

C2 Bolt M12 x 90 HTCHT71819

1 Disc - 55.5mm (2-3/16”)HTCHT71801

2 Disc - 59mm (2-11/32”) HTCHT71802

3 Disc - 62mm (2-7/16”) HTCHT71803

4 Disc - 65mm (2-9/16”) HTCHT71804

5 Disc - 66mm (2-19/32”) HTCHT71805

6 Disc -71.5mm (2-13/16”)HTCHT71806

7 Disc - 73mm (2-7/8”) HTCHT71807

8 Disc - 78mm (3-3/32”) HTCHT71808

9 Disc - 84mm (3-5/16”) HTCHT71809

3

Parts & Service: 020 8988 7400/E-mail:Part[email protected] or [email protected]

METHOD OF USE

WARNING: THE VEHICLE MUST BE PROPERLY PREPARED, AND

ADEQUATELY SUPPORTED ON AXLE STANDS, ON FIRM LEVEL GROUND,

BEFORE ANY OPERATION USING THIS TOOL IS PERFORMED.

INSTALLING SEALS & BEARINGS

Assemble the parts as shown in the example, selecting the components

which fit the job in hand. Ensure the large nut (H) is screwed fully on to the

bolt (F), and all components are entirely square before tightening.

HUB PULLING

It is possible to remove a hub from the swivel joint,

using the bolts (C) supplied.

The appropriate size bolts are screwed into the holes

in the wheel flange, so that they bear up against

the surface of the swivel joint.

Screw in the bolts progressively to pull off the hub.

For hubs where the wheel is mounted on studs, a

slide hammer type puller must be used.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for its intended purpose. Faulty goods

should be returned to their place of purchase. No product can be returned

to us without prior permission. This guarantee does not effect your statutory

rights.

Dieses Handbuch passt für folgende Modelle

1

Andere Clarke Werkzeuge Handbücher

Clarke

Clarke CAT33B Installations- und Betriebshandbuch

Clarke

Clarke CHT204 Bedienungsanleitung

Clarke

Clarke Strong-Arm CLL500 Handbuch

Clarke

Clarke CFC100 Installations- und Betriebshandbuch

Clarke

Clarke CRT 40 Bedienungsanleitung

Clarke

Clarke X-PRO CAT170 Installations- und Betriebshandbuch

Clarke

Clarke TPG30P Bedienungsanleitung

Clarke

Clarke CAT216 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CWJ700 Bedienungsanleitung

Clarke

Clarke IT1500 Bedienungsanleitung

Clarke

Clarke CAT66 Bedienungsanleitung

Clarke

Clarke CHT 141 Bedienungsanleitung

Clarke

Clarke CDTJ12 Bedienungsanleitung

Clarke

Clarke CAT114 Bedienungsanleitung

Clarke

Clarke CAT138 Installations- und Betriebshandbuch

Clarke

Clarke CHT733 Bedienungsanleitung

Clarke

Clarke CAT125 Installations- und Betriebshandbuch

Clarke

Clarke SBR305 Bedienungsanleitung

Clarke

Clarke CBS4 Bedienungsanleitung

Clarke

Clarke CAT29B Installations- und Betriebshandbuch

Clarke

Clarke KIT700 Bedienungsanleitung

Clarke

Clarke CHT172 Bedienungsanleitung

Clarke

Clarke CHT697 Installationsanleitung

Clarke

Clarke CHT877 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung