Clarke X-PRO CAT208 Installations- und Betriebshandbuch

OPERATING & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC1119 - ISS 1

3 IN 1 COMBINATION AIRTOOL KIT

MODEL NO: CAT208

PART NO: 3120525

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE 3 in 1 Combination Air Tool Kit

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

Please keep these instructions in a safe place for future reference.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not affect your statutory rights.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATIONS

Please note that the details and specifications contained herein are correct at the time

of going to print. However CLARKE International reserve the right to change

specifications at any time without prior notice.

Model Number CAT208

Dimensions (L x W x H) 198 mm (right angle grinder)

201 mm (die grinder)

266 mm (ratchet wrench)

x 72 mm x 43 mm

Weight 2.4 kg (complete)

Air Inlet Size 1/4”BSP (female)

Operating Pressure 90 psi (6.2 bar)

Air Consumption 4 cfm (average)

Speed settings Variable speed trigger

Die Grinder

Max No Load Speed

Collet size

Weight

18000 rpm @ 90psi

1/4“(6 mm)

0.795 kg

Right angle die grinder

Max No Load Speed

Collet size

Weight

15000 rpm @ 90psi

1/4”(6 mm)

0.915 kg

Ratchet wrench

Max No Load Speed

Reverse action

Maximum torques

Drive size

Weight

180 rpm @ 90psi

F/R knob

60 ft/lb (85 Nm)

3/8”

1.4 kg

Sound Pressure Level (LpA dB) 86 dB(A) (all tools)

Sound Power Level (LwA dB) 99 dB(A) (all tools)

Vibration Levels 3.95 m/s2(uncertainty factor 1.5 m/s2)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

GENERAL SAFETY RULES

THE WORK ENVIRONMENT

1. ALWAYS keep the work area clean and tidy.

2. ALWAYS dress appropriately - Do not wear loose clothing or jewellery. Tie

long hair out of the way.

3. ALWAYS keep children and visitors away - Do not let children handle the air

tool.

4. DO NOT operate the tool where there are flammable liquids or gases.

USE OF AIR POWERED TOOLS

1. ALWAYS stay alert and use common sense - do not operate the air tool

when you are tired or under the influence of alcohol, drugs or medication.

2. ALWAYS wear eye protectors when using the air tool - Eye protectors must

provide protection from flying particles from the front and the side.

3. ALWAYS wear ear protectors when using the air tool.

4. DO NOT overreach - Keep proper footing and balance at all times.

5. DO NOT use oxygen, CO2, combustible gases or any type of bottled gas as

a source of power for the air tool.

6. DO NOT connect the air supply hose with your finger on the trigger.

7. DO NOT exceed the maximum pressure for the air tool of 90 psi / 6.2 bar.

8. ALWAYS check hoses for leaks or worn condition before use, and ensure

that all connections are secure.

9. DO NOT use the air tool for any other purpose than that described in this

manual.

10. ALWAYS keep the air hose away from heat, oil and sharp edges.

11. DO NOT fit the air tool to a stand or clamping device that may damage it.

12. DO NOT carry out any alterations or modifications to the air tool.

13. ALWAYS disconnect from the air supply when:

• Performing any maintenance.

CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN

PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

• The air tool is not in use.

• The air tool will be left unattended.

• Moving to another work area.

14. DO NOT use the air tool if it is defective or operating abnormally.

15. DO NOT damage the air tool by applying excessive force.

16. ALWAYS maintain the air tool with care. Keep it clean for the best and

safest performance.

17. Quick change couplings should not be located at the air tool. They add

weight and could fail due to vibration.

18. DO NOT force or misuse the air tool. It will do a better and safer job at the

rate for which it was designed.

19. These air tools vibrates with use. Vibration may be harmful to your hands or

arms. Stop using the air tool if discomfort, a tingling feeling or pain occurs.

Seek medical advice before resuming use.

20. DO NOT carry the air tool by the air supply hose.

21. DO NOT carry the air tool with your finger on the trigger.

22. When not in use, disconnect the air tool from the air supply and store in a

dry place out of the reach of children.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW

When opening the blow moulded case for the first time, check that all the

items are present. Any damage or deficiency should be reported to your

CLARKE dealer immediately.

NO DESCRIPTION NO DESCRIPTION

A Right Angle Drive attachment D 4 x Collet Wrenches (11,14,17

&19 mm)

B Ratchet wrench attachment E 1/4” Male Connector

C Die grinder attachment

1 Grease nipple 3 Trigger

2 Quick release locking collar 4 Air Inlet

5 Quick connector

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPRESSED AIR REQUIREMENTS

A typical air line layout is shown below. If an automatic in-line filter/regulator is

used it will keep the tool in good condition, but should be regularly checked

and topped up with oil. SAE 10 oil should be used and the lubricator adjusted

to approx 2 drops per minute.

Use only clean, dry, regulated compressed air as a power source.

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF

COMPRESSORS AND COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

Air compressors used with the air tool must comply with the appropriate

European Community Safety Directives.

The air hose should be rated at least 150% of the maximum operating pressure

of the tool.

A build-up of moisture or oil in the air compressor will accelerate wear and

corrosion in the tool. ensure any moisture is drained from the compressor daily

and the inlet filter is kept clean.

If an unusually long air hose is required, (over 8 metres), the line pressure or the

hose inside diameter may need to be increased. The air hose must be rated at

least 150% of the maximum operating pressure of the air tool.

Never exceed the maximum operating pressure for the air tool. It is

recommended that air pressure to the air tool does not exceed 90 psi at the

air tool when running. Higher pressures and unclean air will shorten the life of

the air tool due to faster wear and is a possible safety hazard.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

CONNECTING THE AIRLINE

1. Remove the plastic blanking plug from the air inlet connection.

2. Pour 2-3 drops of airline oil into the oil filling port. This should be done

regardless of whether or not a lubricated air supply is to be used.

3. If required, connect an in-line mini oiler to the tool.

• A mini oiler helps to prolong the life of any air tool.

4. If a mini-oiler is not being used, run a few drops of oil through the tool

before use. It can be entered through the airline connector or via the hose

at the nearest connection to the air supply.

5. Connect a suitable hose as shown

or use the snap connector to

connect directly to the hose.

6. Connect the other end of the hose

to the compressor.

7. Turn on the air supply and check

for air leaks. Rectify any found

before proceeding.

• PTFE tape may be useful for

sealing threaded connections.

8. If using a mini oiler, place a sheet of paper next the exhaust port and hold

the throttle open for approximately 30 seconds. The oil volume is correctly

set when a light stain of oil can be seen on the paper. Excessive oil should

be avoided.

9. Your air tool is now ready for use.

FITTING THE ATTACHMENTS

This 3-in-1 tool combi tool features an interchangeable tool head with quick-

release coupling. Choose your tool attachment.

Select the required tool head assembly (A, B, or C on page 6) and offer to the

main housing. Align the hexagonal quick-connection adapter (5) to the inner

WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU

ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF AIR

COMPRESSORS AND COMPRESSED AIR SUPPLY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

hexagonal socket and insert. Pull the quick release locking collar backward

with one hand.

Release the quick release collar to retain the tool head assembly (A, B, or C).

Check that the tool head assembly is securely locked in place

THE DIE GRINDERS

FITTING THE GRINDING STONE

IMPORTANT: Never use chipped or cracked grindstones.

1. Slip the shank of the chosen

grinding stone into the collet and

tighten the screw cap finger tight.

2. Place the smaller of the two

wrenches (11mm) over the collet

seat to stop the tool from rotating.

3. Use the larger wrench (17mm) to

fully tighten the collet and grip the

stone in position as shown.

4. If another collet is to be used,

undo the screw cap completely and pull out the collet from the collet seat.

Replace it with the new collet and screw the cap loosely back on.

Inhaltsverzeichnis

Andere Clarke Werkzeuge Handbücher

Clarke

Clarke TPG30P Bedienungsanleitung

Clarke

Clarke CEA150 Installations- und Betriebshandbuch

Clarke

Clarke CAT218 Installations- und Betriebshandbuch

Clarke

Clarke CONTRACTOR CHJ110 Bedienungsanleitung

Clarke

Clarke CAT29B Installations- und Betriebshandbuch

Clarke

Clarke CHT877 Bedienungsanleitung

Clarke

Clarke CONTRACTOR CSJ100 Bedienungsanleitung

Clarke

Clarke CAT114 Bedienungsanleitung

Clarke

Clarke CBS4 Bedienungsanleitung

Clarke

Clarke CRT 40 Bedienungsanleitung

Clarke

Clarke CHT733 Bedienungsanleitung

Clarke

Clarke X-PRO CAT170 Installations- und Betriebshandbuch

Clarke

Clarke GWH8 Bedienungsanleitung

Clarke

Clarke CHT878 Bedienungsanleitung

Clarke

Clarke CAT33B Installations- und Betriebshandbuch

Clarke

Clarke CAT138 Installations- und Betriebshandbuch

Clarke

Clarke CAR15PC Bedienungsanleitung

Clarke

Clarke CHT 454 Bedienungsanleitung

Clarke

Clarke CAT33B Installations- und Betriebshandbuch

Clarke

Clarke CHT172 Bedienungsanleitung

Clarke

Clarke CAR8P Bedienungsanleitung

Clarke

Clarke CAT216 Installations- und Betriebshandbuch

Clarke

Clarke CHT691 Bedienungsanleitung

Clarke

Clarke Air CAT62 Installations- und Betriebshandbuch

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung