Classe Audio Omega Super Audio Bedienungsanleitung

OMEGA ISSUE 2 DEC ‘98

CLASSÉ AUDIO

OMEGA

POWER AMPLIFIER

OMEGA

OWNER'S MANUAL

OMEGA ISSUE 2 DEC ‘98

-2-

CLASSÉ DESIGN PHILOSOPHY

1. REPEATED LISTENING DESIGN SESSIONS:

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB

boards etc.), and adjusting many specific operating voltages within proper engineering ranges,

producing an overall sonic recipe giving the most natural harmonic realism of music typical of

instruments in a live performance.

2. CIRCUIT DESIGN:

The OMEGA is based on Classé’s whole history of designing and building High End

amplifiers.The OMEGA is an Ultra- High performance amplifier of incredible sonic realism

capable of transmitting to the listener the emotional essence of the music. The OMEGA is

actually two completely separate amplifiers with two massive toroidal transformers totalling

5KVA, each with their own power cords and a huge storage capacity which totals over 100,000

uF per channel. The OMEGA has sixteen high voltage/current Bi-Polar output devices per

channel. Discrete high voltage/current voltage regulation for the pre-driver and input sections.

Also featured are heavily gold plated bars connecting supplies of the output devices. Gold plated

input and output connectors. Oxygen free copper wiring. All signal carrying cables are shielded

and have Litz type configuration. The OMEGA is symmetrical from input to output

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS:

Choosing the best attainable quality parts and materials combined with the advantages of the two

above-mentioned areas provides Classé owners with years of proven trouble free reliability and

musical enjoyment.

OMEGA ISSUE 2 DEC ‘98

-3-

OMEGA

OWNER'S MANUAL

TABLE OF CONTENTS

UNPACKING & SET-UP.............................................................................. 4

GENERAL CONNECTIONS........................................................................ 5

CONNECTIONS FOR REGULAR AND BALANCED INPUTS….…..... 8

PROTECTION CIRCUIT............................................................................... 10

IR IN AND OUT…………………………………………………….…… 11

SPECIFICATIONS………………………………………….…………..... 14

OMEGA ISSUE 2 DEC ‘98

UNPACKING & SET-UP

Your CLASSÉ OMEGA power amplifier is packed in high density, semi-rigid foam placed

in a special Fiberglas case. To remove the unit, put the fibreglass case with the Classé lettering right

side up. Unlock the four (4) case locking devices by first lifting the tabs, and turning them fully

counter clockwise. Then, pull the tabs; the locking devices will pivot downwards. You can now

remove the large top portion of the case. Take the unit out of the base of the case and remove the

plastic bag and inspect the unit for any concealed damage. Apart from the owner's manual, please

ensure the following has also been included:

1) Two (2) detachable A.C. linecord

2) Nut driver for output connectors

Please report any damage or missing parts to your dealer immediately.

Place the OMEGA at or near its final set-up position, allowing 8 inches at the rear for

tightening the speaker output connectors.

The power transformers in the OMEGA are located at the front-center of the unit. Ideally, a

few feet should separate this area from components which potentially could pick up hum. These

include preamplifiers, turntables, and interconnect cables. In terms of providing adequate airspace

for cooling, a good rule of thumb is to allow 6 inches above and 3 inches on each side of the unit.

Check the Serial Number sticker on the back of the unit for the correct operating voltage.

The OMEGA has two external AC fuses, the rating of which should be as follows:

LINE VOLTAGE FUSE RATING

100 or 120 V.A.C. 20 AMP SLOW BLOW, 125 or 250 volts

220 or 240 V.A.C 15 AMP SLOW BLOW, 250 volts

OMEGA ISSUE 2 DEC ‘98

GENERAL CONNECTIONS

A.C. LINE

Insert the 2 linecords into the A.C. receptacle on the rear of the unit. PLEASE MAKE

SURE YOU HAVE PREVIOUSLY HOOKED UP THE SPEAKERS AND PREAMPLIFIER

TO YOUR AMPLIFIER BEFORE CONNECTING THE AC POWER CORD TO THE

AMPLIFIER.

IMPORTANT NOTE

CAUTION: SAFETY INSTRUCTIONS

DISCONNECT THE 2 AC LINE CABLES BEFORE MAKING ANY OTHER

CONNECTIONS. "FLOATING THE GROUND” OR DEFEATING THE GROUND ON A

3-PRONG LINECORD MAY CREATE A SHOCK HAZARD. CONNECT ALL INTERCON-

NECT CABLES BETWEEN THE ELECTRONICS BEFORE CONNECTING THE A.C.

LINECORDS TO THE WALL OUTLETS. THIS WILL REDUCE THE POTENTIAL SHOCK

HAZARD. SEE ALSO THE WARRANTY SECTION OF THIS OWNER'S MANUAL.

STEREO

Input and output connectors are clearly marked on the back of the amplifier. Left/Right

connections are oriented from the front of the unit. Stereo output connections are marked above the

connectors. Switch stereo/mono switch to STEREO position. (The OMEGA is preset at the factory

for STEREO.) Use only high quality interconnect and loudspeaker cables, and make all connections

tight. If the RCA input plugs are loose, remove them and pinch down the ground leaves slightly with

pliers. Observe correct phasing of the loudspeaker connections, and tighten.

OMEGA ISSUE 2 DEC ‘98

STEREO (CONTINUED)

DO NOT OVERTIGHTEN the output connectors. When powering up the OMEGA in stereo mode,

the left channel LED will blink for approximately 20 seconds, when the sequence is completed, the

LED will turn SOLID RED. Then, the right channel LED will also blink for approximately 20

seconds and will also turn solid red once it has completed its turn on sequence.

MONO

Please read through the previous Stereo section for general notes on securing good

connections, and safety tips. If the unit has been previously used in stereo, make sure it is OFF, and

remove all connections, including the AC line cable. Make sure the STEREO/MONO switch is

switched to the MONO position. NOTE: The Stereo-Mono switch will not operate if the amplifier is

turned on, you will NOT be able to change from one mode to the other, as the mode is “locked”

while the amplifier is on.

When the turn on sequence has been completed with the unit set for MONO operation, only

the CENTER LED will light up.

The MONO "Input" is the "left channel input", as marked. The unused right channel input is

automatically disconnected. Correct output phase MONO connections are marked below the

connectors.

Repeat the above MONO settings and connections on the second OMEGA to be used for

the other channel.

Please remember that the negative output connection of a bridged amplifier is NOT a

ground. Do not use a "common ground” switch-box set-up. Do not use with electronic crossovers

which have a common ground. Connecting two bridged amplifiers to a common ground device of

any sort will cause the amplifiers to fail.

OMEGA ISSUE 2 DEC ‘98

MONO OPERATION

As stated above, either the regular or balanced inputs can be used in stereo or mono.

Connect a single interconnect, either regular or balanced, to the left channel input of each amplifier.

See the "Mono" section above for complete details. NOTE: Neither the Stereo-Mono switch nor the

REGULAR/ BALANCED switch will operate while the amplifier is turned on. You will NOT be able to

change from one mode to the other, as these modes are “locked” while the amplifier is on. To

activate the circuit, turn off the unit and engage the STEREO/MONO switch to REGULAR. If the unit has

not been turned off before engaging the switch, turn off the unit, wait for about 10 seconds, and turn

the unit on again, the circuit will then engage.

OMEGA ISSUE 2 DEC ‘98

CONNECTIONS FOR REGULAR OR BALANCED INPUTS:

The CLASSÉ OMEGA power amplifier is equipped with both regular and balanced inputs.

Either one may be used SEPARATELY, BUT NOT SIMULTANEOUSLY. The balanced inputs must be

connected to a preamplifier which has balanced main outputs. Balanced interconnects with "XLR"

connectors are also required. Regardless of the amplifier inputs used, stereo or mono operation is

possible on the OMEGA.

REGULAR INPUTS

Engage the REGULAR/BALANCED switch to the position marked "REGULAR". (The amplifier is

factory set for “REGULAR”.) NOTE: The REGULAR/ BALANCED switch will not operate if the

amplifier is turned on; you will NOT be able to change from one mode to the other, as the mode is

“locked” while the amplifier is on. To activate the circuit, turn off the unit and engage the

REGULAR/BALANCED switch to REGULAR. If the unit has not been turned off before engaging the

switch, turn off the unit, wait for about 10 seconds, and turn the unit on again, the circuit will then

engage. Connect the regular interconnects to the RCA input jacks on the rear panels of the OMEGA.

The balanced connectors are automatically disabled.

BALANCED INPUTS

Switch the

REGULAR/BALANCED switch to the position marked "BALANCED". A balanced

preamplifier and balanced interconnects are also required. NOTE: The REGULAR/ BALANCED switch

will not operate if the amplifier is turned on; you will NOT be able to change from one mode to the

other, as the mode is “locked” while the amplifier is on. If the unit has not been turned off before

engaging the switch, turn off the unit, wait for about 10 seconds, and turn the unit on

OMEGA ISSUE 2 DEC ‘98

BALANCED INPUTS (CONTINUED)

again, the circuit will then engage. For use with balanced preamplifiers other than Classé, the

wiring of the 3-pin XLR connectors must be matched to that of the CLASSÉ OMEGA which is

wired as follows:

PIN 1: SHIELD (Should be connected only at the preamplifier end of the cable)

PIN 2: POSITIVE (NON-INVERTED) SIGNAL, “HOT”

PIN 3: NEGATIVE (INVERTED) SIGNAL

All Classé preamplifiers and amplifiers are configured as above. Some preamplifiers from other

manufacturers have PIN-3 set as the positive or “HOT” side. If this is true of your preamplifier, and

you wish to maintain absolute phase throughout your system, the interconnects must have the wire

which is connected to PIN-3 at the preamplifier output end switched to PIN-2 at the amplifier input

end and the wire which is connected to PIN-2 at the preamplifier output switched to PIN-3 at the

amplifier input end.

Having confirmed the correct connections, plug the XLR connectors of the balanced

interconnects into the locking XLR connectors on the rear panel of the OMEGA. Push the

connectors in until the locking mechanism clicks. (To remove the connectors, press the tab above the

connector while pulling gently on the connector body.)

OMEGA ISSUE 2 DEC ‘98

PROTECTION CIRCUIT

A special circuit in the Classé OMEGA continuously monitors the output audio signal to

detect output overload, clipping or DC content. In addition, each channel has two front end supply

voltage fuses, located on the front end voltage regulation board, to protect the input circuitry from

damage due to overload. There is a green LED for the negative voltage supply and a red for the

positive. If a fuse fails, the corresponding LED goes out, alerting you of the fact. (These fuses are

2AG 1 PT, 1 amp fast blow).

There are also line AC fuses, located at the rear of the amplifier immediately above each IEC

receptacle. There are no LEDs monitoring the condition of these fuses.

If the protection circuit of the unit is triggered or any of the fuses has blown, the FRONT

PANEL POWER LED(S) will go to BLINKING GREEN, indicating a “fault” condition. If the left

LED is BLINKING GREEN, the fault condition should be located at the left channel, if the right

channel LED is BLINKING GREEN, the fault will be located to the right channel regardless if the

unit is used in mono or stereo.

IF THE PROTECTION CIRCUIT HAS BEEN TRIGGERED, TURN THE OMEGA OFF.

.After the situation which has triggered the protection circuit has been clearly identified and

corrected, attempt to re-start the unit. IF THE UNIT STILL GOES INTO PROTECTION MODE,

OR IF IT APPEARS THAT PROTECTION FUSES DID BLOW, CONTACT YOUR LOCAL

DEALER. DO NOT TRY TO CHANGE A BLOWN FUSE. REPLACING A FUSE WITHOUT

CHECKING FOR COMPONENT FAILURE COULD RESULT IN FURTHER, SERIOUS

DAMAGE TO VITAL COMPONENTS IN YOUR AMPLIFIER. CONTACT YOUR LOCAL

DEALER or Customer Service at the Classé Audio, Inc --- (514) 636 63 84.

Andere Handbücher für Omega Super Audio

Inhaltsverzeichnis

Andere Classe Audio Verstärker Handbücher

Classe Audio

Classe Audio Delta MONO Bedienungsanleitung

Classe Audio

Classe Audio 100-A Bedienungsanleitung

Classe Audio

Classe Audio CA-M400-CH Bedienungsanleitung

Classe Audio

Classe Audio Delta Series Bedienungsanleitung

Classe Audio

Classe Audio SSP-25 Bedienungsanleitung

Classe Audio

Classe Audio CP-700 - V1.8 Bedienungsanleitung

Classe Audio

Classe Audio CP-500 - V2.0 Bedienungsanleitung

Classe Audio

Classe Audio CP-500 - V2.8 Bedienungsanleitung

Classe Audio

Classe Audio CA-M400 Bedienungsanleitung

Classe Audio

Classe Audio C-501 Bedienungsanleitung

Classe Audio

Classe Audio C-103 Bedienungsanleitung

Classe Audio

Classe Audio CA-2100 Bedienungsanleitung

Classe Audio

Classe Audio CP-65 Bedienungsanleitung

Classe Audio

Classe Audio CA-5200 Bedienungsanleitung

Classe Audio

Classe Audio CA-M400 Bedienungsanleitung

Classe Audio

Classe Audio CAV-75 Bedienungsanleitung

Classe Audio

Classe Audio CA-151 Bedienungsanleitung

Classe Audio

Classe Audio CP-35 Bedienungsanleitung

Classe Audio

Classe Audio CA-400 Bedienungsanleitung

Classe Audio

Classe Audio DR-10 Bedienungsanleitung

Classe Audio

Classe Audio CP-800 Bedienungsanleitung

Classe Audio

Classe Audio SSP-30 MKII Bedienungsanleitung

Classe Audio

Classe Audio CA-301 Bedienungsanleitung

Classe Audio

Classe Audio S-1000 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung