Claudgen HE7237SL Bedienungsanleitung

 

General information ------------------------------------------------------------ 1

Dimensions ---------------------------------------------------------------------- 2

Installation Details -------------------------------------------------------------- 3

Electrical Connections -------------------------------------------------------- 4

Operation ------------------------------------------------------------------------- 5

Servicing & Maintenance ----------------------------------------------------- 6

41001476 Iss 01













CONSORT Wireless

controller CRX2

SLPB SLTI SLVT SLVTB



 

This instruction manual describes the CLAUDGEN

Surface Warm Air Ceiling Heaters.

The heater is designed to be suspended from the

ceiling.

 

All installations must be in accordance with the

regulations in force in the country of use.

These instructions must be handed to the user on

completion of the installation.

Installers and service engineers must be able to

demonstrate competence and be suitably

qualified in accordance with the regulations in

force in the country of use.

To ensure continued and safe operation it is

recommended that the appliance is serviced

annually.

The heater outlet / inlet must not be obstructed

during use.

 

Electrical supply is 230/240V single phase,

Neutral and Earth. The maximum cable inlet size is

4mm².

It is recommended that the electrical supply to the

base unit in the heater is via an appropriate

switched isolator in accordance with the

regulations in force in the country of use and must

be via a fused isolator having a contact separation

of greater than 3mm on all poles.

BMS control, time switches, room thermostats and

door interlocks can be installed at the discretion

and responsibility of the installer.

All units must be wired in accordance with I.E.E

regulations for the Electrical Equipment of

Buildings and the installer should ensure that a

suitable isolating switch is connected in the mains

supply.



The HE7237SL, HE7247SL, HE7267SL heaters are

supplied without a controller. The `SL` models will

not work without the controller. See section 5.1 for

more details.



The HE7237RX, HE7247RX, HE7267RX heaters are

supplied without a controller. The `RX` models will

not work without the controller. See section 5.2 for

more details.

 

All units should be installed horizontally. It is

recommended that the ceiling heater is

suspended using four 10mm rods.

Care must be taken to allow complete free air

movement into the inlet grilles of the unit to

ensure the correct working operation of the

heater. If the HE7237SL/RX or HE7247SL/RX heaters

are mounted close to the wall or corner the

discharge opening should be facing the wall. The

minimum distance from the wall or corner is 0.8m

or 1.2m for the HE7267SL/RX.

 

It is acceptable for the heater to sit flush to the

ceiling.

The minimum mounting height (floor to grille) is

2.2m for the HE7237SL/RX, HE7247SL/RX and 2.5m

for the HE7267SL/RX.

The recommended mounting height is 2.5m for

the HE7237SL/RX, HE7247SL,RX and 3m for the

HE7267SL/RX.

CONSORT SL Controllers

41001476 Iss 01

SLPB SLTI

SLVT

CONSORT Wireless

controller CRX2

SLVTB



41001476 Iss 01

SUSPENSION POINTS

 

 

Sole liability rests with the installer to ensure that all

site safety procedures are adhered to during installa-

tion.

Sole liability rests with the installer to ensure that

protective safety wear such as hand, eye, ear and

head protection is used during installation of the

product.



Do not rest anything especially ladders against the

product.

 

Units conform to the European electrical standard

BS EN 60335-2-30

41001476 Iss 01





 

It is the sole responsibility of the installer to en-

sure that the points of attachment to the building

are sound. Care must be taken to allow complete

free air movement into the inlet grilles of the unit to

ensure the correct working operation of the heater.

Carefully unpack the unit. The unit is supplied with

a length of self-adhesive foam strip. This can be

cut into lengths and is to be laid on the 4 sides of

the bottom of the heater casing . This will ensure

that the unit assembly is free from vibration.







-Split and remove shroud

A pair of machine screws hold each shroud half

together at each joint. A machine screw secures

each shroud half to each appliance beam. Re-

move these machine screws and slide each

shroud half off the appliance base panel. The

base panel fits inside the shroud halves.

The diffuser is already clipped into and under the

base panel and need not be removed.

- Hanging Rod Positions

With the shroud removed the two appliance

beams reveal the holes/slots shown and dimen-

sioned below. It is required that two 10 mm

hanging rods (stud bars) support each appliance

beam. The rods pass through and into

each appliance beam. Support washers

together with nuts locate and lock the

appliance beams after adjustment to

level the appliance.

- Replace Shroud Halves

The reverse of above. Slide shrouds

beneath and around base panel. Se-

cure each shroud half to each appliance

beam with machine screws. Screw

shroud halves together at each joint.

 

These units are suitable for connection

to a 230/240 Volt 50 Hz single phase

supply.

The appliance shall be connected to the

supply via an appropriate switched fused double

pole isolator having a contact separation of great-

er than 3mm. Test for correct operation and refit

the cover.









For connection to the mains supply it will be

necessary to open the terminal cover at the side/

back of the unit to connect the supply from the

controls prior to refitting the cover. Wire in accord-

ance to the wiring diagrams.

For safety reasons, a sound earth connection

must always be made to the unit before it is put to

use. The unit should be wired in accordance with

IEE Regulations for the Electrical Equipment of

Buildings.





SUSPENSION POINTS



TOP OR SIDE CABLE ENTRY

 

The heaters HE7237SL, HE7247SL and HE7267SL can be controlled by any CONSORT SL wireless

controller. Each SL controller can control any number of heaters providing they are in the RF range.

For more details please follow the instructions supplied with the controller.







 

41001476 Iss 01

SLPB SLVTBSLTI

CONSORT Wireless

controller CRX2

CONSORT SL Controllers

 

The heaters HE7237RX, HE7247RX and HE7267RX can be controlled by CONSORT wireless con-

troller CRX2. The heaters will not work without a controller. Each controller has unique identification

code, it can control unlimited number of heaters and will not interfere with other controllers within the

building. For more details please follow the instructions supplied with the controller.

SLVT

41001476 Iss 01

    

   

    



To obtain the best results from the heater, it is

essential to avoid the accumulation of dust and

dirt within the unit on the air inlet and discharge

grilles. For this reason regular cleaning is

necessary.

Cleaning of the fan is best carried out with a soft

brush.

The product should be serviced annually.

Servicing shall be undertaken by a competent

person.

 

If the heater does not operate a competent service

engineer should be called to identify the nature of

the fault.

All heaters are fitted with motor thermal protection.

Other faults in relation to the element, motor and

wiring should be identified using conventional fault

finding techniques.

In the event that electrical components are

replaced, please ensure that electrical safety

checks in accordance with the regulations in force

in the country of use are undertaken.

-

The units are protected from overheating in the

event of fan failure or an obstruction of the free

airflow, by thermal cut outs. If this happens the

thermal cut outs switch off the appliance. The ap-

pliance will not operate until the heater is discon-

nected from the mains supply and it has cooled

down.

If this fault re-occurs again, refer to the section

‘6.4 fault finding’.



  

If the heater will not operate, disconnect it from

the mains and arrange for a certified electrician to

attend and investigate the reason.

 

a) Split and remove shroud

b) Remove the grille.

c) Disconnect the internal wiring from the blower

d) Remove the four screws fixing the fan heater

assembly to the back of the case.

e) The fan heater assembly can now be eased

forward and removed from the heater case.

f) Fit replacement fan heater and reassemble in

reverse order.

 

It is essential when ordering spares or replace-

ment parts to state the model number and the

serial number on the rating label fixed to the side

of the unit below the terminal cover.

In the interest of progress the Company reserve

the right to vary specifications from time to time

without notice. The material listed is offered sub-

ject to the Company’s General Conditions of Sale,

a copy of which can be obtained on request.



Should you need any advice on the use of your new Consort product, or

should you require service or repair, please contact our Helpline:

Consort Equipment Products Limited

Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT

Tel: 01646 692172 Fax: 01646 695195

Email: [email protected] Web: www.consortepl.com

Operation hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm

BS EN ISO 9001 Registered Company No FM12671

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Claudgen Heizung Handbücher

Claudgen

Claudgen CH06CSi Bedienungsanleitung

Claudgen

Claudgen CH06CSiRX Bedienungsanleitung

Claudgen

Claudgen HE7433 Original Betriebsanleitung

Claudgen

Claudgen SCREENZONE RAC1306 Bedienungsanleitung

Claudgen

Claudgen HE7237 Handbuch

Claudgen

Claudgen ScreenZone HE8409 Bedienungsanleitung

Claudgen

Claudgen HE7010 Handbuch

Claudgen

Claudgen RAC4500 Handbuch

Claudgen

Claudgen RCT250 Handbuch

Claudgen

Claudgen CA1309S Handbuch

Claudgen

Claudgen HE7010SL Gebrauchs- und Wartungshandbuch

Claudgen

Claudgen CH06CS Handbuch

Claudgen

Claudgen HE8320 Original Betriebsanleitung

Claudgen

Claudgen HE7230W Montage- und Bedienungsanleitung

Claudgen

Claudgen CA1509S Original Betriebsanleitung

Claudgen

Claudgen HE7402-31 Handbuch

Claudgen

Claudgen SCREENZONE RAC1306 Bedienungsanleitung

Claudgen

Claudgen ScreenZone RAC10HL Bedienungsanleitung

Claudgen

Claudgen Heat-Zone Handbuch

Claudgen

Claudgen HE7402 Original Betriebsanleitung

Claudgen

Claudgen HE7245 Bedienungsanleitung

Claudgen

Claudgen ScreenZone CA2015S Bedienungsanleitung

Claudgen

Claudgen ScreenZone RAC0603 Bedienungsanleitung

Claudgen

Claudgen HE8320 Handbuch

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung