Clearfield FieldSmart FxMP Bedienungsanleitung

FieldSmart®FxMP Panel & Standard Frame

Installation Manual ______________________________________________________

Manual 019807 REV A - June 2018

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxMP Panel & Standard Frame

Installation Manual _________________________________________________________

Manual 019807 REV A - June 2018

Table of Contents

Application 3

Description 3

Technical Specications 3

Tools and Optional Materials 4

Standard Frame Floor Installation 5

Standard Frame Raised Floor Installation 7

Standard Frame Interbays and End Guards Installation 11

Standard Frame Grounding 11

FxMP Panel Mounting 12

Cable Mounting and Routing 16

Routing Ribbon Fiber 19

Cassette Removal/Installation 20

Splicing/Buffer Tube Storage 24

FxMP Tie Panels 30

FxMP Designation Card 32

Connector Cleaning Procedure 33

Standard Warranty 36

Proprietary Notice 37

Technical Support 37

FieldSmart®FxMP Panel & Standard Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 019807 REV A - June 2018

Application

Description

Technical Specications

FieldSmart FxMP Panel

Port Density 24 72 96 144 288

Dimensions 1.75” H (44.45mm) 3.5” H (88.90mm) 4” H (101.60mm) 6” H (152.40mm) 11” H (279.40mm)

Ratings Compliant to Telcordia GR-63, GR-449, GR-20 and GR-409

Cassette Types Supported Clearview®Blue

Connector Types SC/UPC, SC/APC, LC/UPC, LC/APC, FC/UPC, FC/APC, ST/UPC, MPO

Cable Types Indoor Riser, Indoor Plenum, Indoor/Outdoor, Outdoor (Riser/Non-Rated), Outdoor Armored (Riser/Non-Rated), FieldShield®

Splice Capacity 12 splices in each Clearview Cassette

Storage Capacity One meter of 250 μm ber

Front Protection 3.25” (82.6 mm) or 4.77” (121.16 mm) radius ngers

Color Almond or black

Material Steel and aluminum with almond powder coating

FieldSmart Standard Frame

Dimensions Available in 7’, 8’ or 9’ heights and in either 19” or 23” widths; depth is 10” (5” frame + 5” guard box)

Ratings Compliant to Telcordia GR-449

Cable Entry Clamp Location On-frame (Note: Cable clamps included with panels)

Material Steel

Standard Frame:

FieldSmart FxDS Standard Frames are available in 7’, 8’ or 9’ heights and in 19” or 23” widths. Frames are

seismic-rated and come with an unequal ange. When used with FieldSmart FxMP Panels, they provide the

highest port density in the industry - up to 1,728 ports in a 7’ frame.

FxMP Panel:

The FieldSmart FxMP Panel is a high density, low maintenance ber distribution panel for use in a data

style rack/cabinet, a 19” (482.60mm) or a 23” (584.20mm) frame. Utilizing the Clearview ®Cassette,

FieldSmart FxMP Panels are intelligently designed to provide the user with superior ber access and

craft-friendly, radius protected ber management for routing and deploying ber jumpers.

Standard Frame:

Frames are used for mounting equipment in a central ofce, head end or data

center applications.

FxMP Panel:

Provides an interconnect or cross-connect environment for up to 288 ports of high density ber

for inside plant and outside plant environments.

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxMP Panel & Standard Frame

Installation Manual _________________________________________________________

Manual 019807 REV A - June 2018

Tools and Optional Materials

Tools:

• Sockets (1/2”, 3/4” and 15/16”)

• Ratchet with Extension

• Phillips Screwdriver

• 1/8” Allen Wrench

• Hammer/Rotary Drill

• 5/8” Masonry Drill Bit

• Blowout Air Bulb or Vacuum with Small Diameter Tube

Materials (ordered separately):

Standard Frame:

• Isolation Pad (19” Frame P/N FMA-L1Z-SUB,

23” Frame P/N FMA-L2Z-SUB)

Floor Mounting:

• Floor Mounting Kit (P/N 009106)

Raised Floor Mounting:

• Raised Floor Mounting Kit (P/N 011236)

Patch and Splice Panels:

• Radius Limiter Brackets for Buffer Tube Slack Storage

(P/N 010600)

Ribbon Fiber Protection:

• High Density Ribbon Breakout Kit (P/N 010475)

• Ribbon Fanout Kit (P/N FMA-MZZ)

Radius Limiter Bracket

Breakout Kit Fanout Kit

Isolation Pad

FieldSmart®FxMP Panel & Standard Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 019807 REV A - June 2018

Standard Frame Floor Installation

Note: Floor mounting hardware is NOT included with the standard frame. Hardware is sold as a separate line item

(Cleareld P/N 009106).

IMPORTANT: If your frame is to be mounted next to a wall, or there are multiple frames in a line-up, you MUST

install the interbay management and end guards BEFORE mounting the frame to the oor.

Tools:

• Hammer (or rotary) drill (with depth gauge recommended)

• 5/8” masonry drill bit

• Socket wrench set

• Blowout air bulb or vacuum with small diameter tube

Using a 5/8” masonry bit, drill the four required holes to a

minimum depth of 2” (approx. 50mm).

Note: If for some reason you have trouble drilling the 5/8” hole,

Cleareld recommends rst drilling a ¼” pilot hole before drilling

out to 5/8”.

Thoroughly clean the dust from each hole, using a vacuum or

blowout air bulb.

Note: To not degrade the anchor’s installed performance, any unused anchor holes (or other nearby holes) in the

concrete within 3” must be lled with an epoxy ller (pour stone) or equivalent. Filled holes must be fully cured before

anchors are installed and torqued.

19” Frame

9 5/8”

22”

23” Frame

9 5/8”

26”

Determine where the frame is going to be installed. Using the isolation pad as a template, mark the 4 holes where

frame will be secured to the oor.

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxMP Panel & Standard Frame

Installation Manual _________________________________________________________

Manual 019807 REV A - June 2018

Place the isolation pad in position over the predrilled holes and align as necessary. Lift the frame onto the isolation

pad and line up with holes.

Ensure that the anchor’s expansion shield is not expanded. Place the end of the anchor into the predrilled hole.

Repeat for the other drilled holes. Make sure the anchor is fully embedded in the concrete.

Align the edges of the 2” square washer parallel with the slots in the frame base to obtain the maximum material

overlap. Once aligned, tap each anchor/washer assembly until it is seated rmly in the hole and against the 2” square

washer.

Pre-tighten each anchor with a socket wrench or box-end wrench; do not use an open-end wrench (which could easily

slip off and cause injury). Before nal tightening, ensure that the frame is properly aligned (in the row and with any

adjacent frames). Torque each anchor to 60 ft-lbs.

Note: When using the break-off type anchor, a torque wrench is not required. The anchor’s (red) torque cap shears

off at a predetermined torque value (approximately 60 ft-lbs.), leaving a green seal on the bolt head, indicating proper

tightening.

The anchoring line up should look like this:

Note: Square

washers will be

packaged in base

of frames

Threaded Rod

FieldSmart®FxMP Panel & Standard Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 019807 REV A - June 2018

Standard Frame Raised Floor Installation

Note: Raised oor mounting hardware is NOT included with the standard frame. Hardware is sold as a separate line item

(Cleareld P/N 011236).

IMPORTANT: If your frame is to be mounted next to a wall, or there are multiple frames in a line up, you MUST

install the interbay management and end guards BEFORE mounting the frame to the oor.

Tools:

• Hammer (or rotary) drill (depth gauge recommended)

• 5/8” masonry drill bit

• Socket wrench set

• Blowout air bulb or vacuum with small diameter tube

Also required is a raised oor mounting kit (Cleareld P/N 011236).

1. 1/2-13 Hex Nut (Qty 8)

2. 1/2 Lock Washer (Qty 4)

3. 1/2 Flat Washer (Qty 4)

4. 1/2-13 x 30 Threaded Rod (Qty 4)

5. Hilti HDI 1/2” Anchor (Qty 4)

6. 1/4 x 2” Flatwasher .515 Hole (Qty 8)

7. Split Tubing 30” (Qty 4)

Screw Sequence for Floor Screw Sequence for Frame

Note: Cleareld recommends installing the anchors directly into the concrete oor.

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxMP Panel & Standard Frame

Installation Manual _________________________________________________________

Manual 019807 REV A - June 2018

Using the isolation pad as a template, mark on the panel(s) of the raised oor the 4 holes where the frame will be se-

cured to the oor. Using a 5/8” drill bit, drill a hole through each of the oblong marks you made with the isolation pad.

Take the threaded rods from the raised oor mounting kit and slide one through each of the holes. Using a hammer

and holding them perpendicular to the oor, tap on the end rmly. The goal is to make a “mark” on the concrete oor

visible enough to see where the 4 holes should be drilled.

Once the concrete oor is marked, remove the threaded rods and oor panels. Using a 5/8” masonry bit, drill the four

required holes to a minimum depth of 2” (approx. 50mm).

Note: If for some reason you have trouble drilling the 5/8” hole, we

recommend rst drilling a 1/4” pilot hole before drilling out to 5/8”.

Thoroughly clean the dust from each hole, using a vacuum or

blowout air bulb.

Note: To not degrade the anchor’s installed performance, any unused

anchor holes (or other nearby holes) in the concrete within 3” must be

lled with an epoxy ller (pour stone) or equivalent. Filled holes must be fully cured before anchors are installed and

torqued.

19” Frame

9 5/8”

22”

23” Frame

9 5/8”

26”

FieldSmart®FxMP Panel & Standard Frame

__________________________________________________________ Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

Manual 019807 REV A - June 2018

Install anchors into the oor. Replace raised oor panels and

insert threaded rods through the four holes.

Note: You are not installing the rods at this point. You are

measuring the rods to be cut to the appropriate length.

Measure the rods 2.5” above the oor and mark with a

permanent marker. Remove the rods and cut each rod at the

mark. Remove the oor panels.

Before installing rods back into the oor, place a nut and then

a washer on the threaded rods. Take the rod and install it into

the anchor installed in the oor.

Tighten the nut down to secure the rod into the oor. Tighten

each bolt to 65 ft-lbs., +10, -0 ft-lbs. The anchor will expand

and secure itself to the oor.

Once all four rods are secure, thread another hex nut, then

washer on each rod. Make sure the nut and washer are

approximately ½” below the raised oor level. This hardware

will be tightened down AFTER the frame is set into place but

BEFORE securely bolting the frame to the oor.

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeCleareld.com • [email protected]

FieldSmart®FxMP Panel & Standard Frame

Installation Manual _________________________________________________________

Manual 019807 REV A - June 2018

Place the oor panels into position, and tighten the previously installed nuts below the raised panel until they make

contact with the panel. Put the isolation pad into place (isolation pad may look different than example).

Lift the frame into place.

Place the square washers onto each rod. Align the edges of the 2” square washer parallel with the slots in the frame

base to obtain the maximum material overlap. Install the isolation washers (packaged with the isolation pad) onto each

rod.

Install the remaining hardware (washers, nuts, etc) from the raised oor installation kit.

Note: Square

washers will be

packaged in base

of frames

Threaded Rod

10.

11.

12.

13.

Inhaltsverzeichnis

Andere Clearfield Bedienfeld Handbücher

Clearfield

Clearfield FieldSmart FxHD Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten