CLEBO-HD AOD-2301 Bedienungsanleitung
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Megapixel HD-SDI
Outdoor Dome Camera
CLEBO-HD AOD-2301
CLEBO-HD AOD-2301 IR
05212012
2
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacturer.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning :
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface :
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
Provide reasonable protection against harmful interference. when the equipment is
operated in a residential environment. This equipment generates, uses, and radiates
radio frequency energy; and if it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications.
3
Table of Contents
Introduction
Installation
Camera OSD Menu and Glossary
Troubleshooting
Specifications
Features
Parts and Descriptions
Dimensions
Included Accessories
Easy Installations
Insstallation
Connecting to Monitor
4
5
6
7
8
9~13
14
17-28
29
30
Adjusting the camera lens 15
3Axis Gimbal Adjustment 16
4
FEATURES*
Sony 1/2.8” CMOS Sensor
Highest Resolution 2.1 Megapixels
720P / 1080P Mode selectable
4x Auto-Focus 3.5~16mm Lens
Double Shutter WDR (Wide Dynamic Range) at 15fps Settings
70ft Range IR with Intelligent Camera Sync (CLEBO-HD AOD-2301 IR)
Electronic Day and Night (CLEBO-HD AOD-2301)
True Day and Night (CLEBO-HD AOD-2301 IR)
AGC / BLC / AWB
3D DNR (3D Digital Noise Reduction)
D-Zoom (1~112 level)
HL Mask (High Light Masking)
Mirror Image Control
Programmable Privacy Zone (24) & Motion Detection
White defecet cancellation (DEFECT DET)
12VDC Support Only
Secondary Video-BNC Output
IP68 Certified (Waterproof)
5
PART & DESCRIPTIONS*
2
3
9
8
5
13
10
6
7
1
12
11
4
1
Lens
3
RS485, Alarm
2
Power input Connctor
12VDC Voltage
Yellow (485+)
Black (485-)
White (Alarm 1)
Red (Alarm 2)
4
BNC (HD-SDI)
11
2nd Video Connector
5
Camera Control Board
12
Safety Wire
6
Bubble
7
Upper Case
8
Flush Mount Case
9
Surface Mount Case
10
Assembly Screws
#8 - 32 x 0.75
13
Mounting Screws
w/o IR IR
6
DIMENSIONS IN MILLIMETERS(INCHES)*
Flush Mount
Surface Mount (I) Indoor, (V) Vandalproof
101
137
17
28
54
98,8
121
118,8
139
36
29
53,8
121
7
INSTALLATION*
Included with Outdoor Dome Camera
1. User Manual
2. Mounting Template
3. Second Video Jack
4. Three (3) Screws and Three (3) Dry Wall Anchors
5. L-Wrench
6. TORX-T20 Bolt
7. TORX-T20 Wrench
1234
567
8
EASY INSTALLATION*
9
SURFACE MOUNT INSTALLATION INSTRUCTIONS*
DC12V
AC24V
UTP
RS485
1. Use the camera’s mounting
template or your camera to
mark the holes as required.
2. Drill holes into the drywall and
insert the drywall mounts into
the holes.
3. Pull wires through and make
connections.
If you need to keep the wiring within the
within the camera
housing, refer to the diagram below.
4. Mount the surface mount
base (junction box) to the
wall.
5. Snap the camera module onto
the base by aligning the red
and black markings on the
base and the camera module.
10
6. Secure the three (3) assembly
screws.
7. Adjust the camera’s position
by using the 3-Axis Gimbal.
8. Tighten the three locking
screws with the L-Wrench
to secure the cover dome
over the camera.
Flush Mount Installation
For a flush mount housing, remove the surface mount base
(junction box). Cut a large hole on a flat surface for the top part
of the flush mount base. Use the three screws fixed to the base
to secure it to the surface of the wall or ceiling.
Follow steps 6 through 8 of the Surface Mount Installation
Instructions to complete the installation.
3
ST4X35
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere CLEBO-HD Sicherheitskamera Handbücher
