Cleco CellTek CTBA Bedienungsanleitung

For additional product information visit our website at www.ClecoTools.com

Quick Installation Guide

P2545KA-EN

2022-12 | REV C

CTBA & CTBP

Data Transmission

P2545KA | 2022-12 | REV C

Apex Tool Group

No part of this document may be reproduced in any way or in any form, in whole or in part, or in a natural

or machine-readable language, or transmitted on electronic, mechanical, optical, or other media, without

the express permission of the Apex Tool Group.

Disclaimer

Apex Tool Group reserves the right to modify, supplement, or improve this document or the product with-

out prior notice.

Trademark

Cleco Production Tools is a registered trademark of Apex Brands, Inc.

Apex Tool Group

670 Industrial Drive

Lexington, SC 29072

USA

Manufacturer

Apex Tool Group GmbH

Industriestraße 1

73463 Westhausen

Germany

Apex Tool Group

P2545KA | 2022-12 | REV C

Content

1About this document ...........................................................................4

1.1 Other documents ............................................................................................................4

1.2 Symbols in the text .........................................................................................................4

2System Layout......................................................................................5

2.1 WLAN communication ....................................................................................................5

2.1.1 Tool Data ........................................................................................................................5

2.1.2 Country-specific channel settings...................................................................................6

2.1.3 Cell planning for access point.........................................................................................7

2.2 Bluetooth communication ...............................................................................................8

3Before Initial Operation........................................................................9

3.1 Requirements .................................................................................................................9

3.2 Install Software ...............................................................................................................9

3.3 Install driver.....................................................................................................................9

4Initial operation...................................................................................10

4.1 Configuring the access point ........................................................................................10

4.1.1 mPro200GC-AP............................................................................................................10

4.1.2 mPro400GCD ...............................................................................................................11

4.2 Configuring RF settings ................................................................................................12

4.3 Configuring Bluetooth settings......................................................................................14

4.4 Installing the Tool..........................................................................................................15

About this document

P2545KA | 2022-12 | REV C

Apex Tool Group

1 About this document

This document is intended for qualified employees responsible for installation and maintenance (adminis-

trators, installers, maintenance technician, service, operator).

It contains information

•for save, appropriate installation and handling. This document is not sufficient for planning complex

network infrastructures.

•about system structure.

The original language of this document is German.

1.1 Other documents

Number

Document

P2260JH

Installation Manual – WLAN Data Transmission

P2280PM

Programming Manual – S168813 mPro400GC(D) & mPro200GC(-AP)

P2372JH

Installation Instruction – S168688 LiveWire Utilities

P2403HW

Hardware Description – mPro200GC(-AP)

P2543BA

Instruction Manual – CTBA & CTBP

P2544PM

Programming Manual – S169263 CTBA & CTBP

S168691 mProRemote Professional

1.2 Symbols in the text

italic

Menu options (e.g., Diagnostics) input fields, check boxes, radio buttons or dropdown

menus.

Indicates selection of a menu option from a menu, e.g., File > Print.

<...>

Specifies switches, pushbuttons or the keys of an external keyboard, e.g., <F5>.

Courier

Indicates Filenames and paths, e.g., setup.exe.

•

Indicates lists, level 1.

Indicates lists, level 2.

Indicates options.



Indicates results.

1. (...)

2. (...)

Indicates action steps.

►

Indicates single action steps.

System Layout

Apex Tool Group

P2545KA | 2022-12 | REV C

2 System Layout

The communication between the controller and the tool is possible via WLAN or Bluetooth. The tool can

communicate with a mPro200GC-AP or mPro400GCD controller.

To communicate with the controller, the tools must be in the mPro mode.

2.1 WLAN communication

The system layout described is based on communication via WLAN. The access point is integrated in the

mPro200GC-AP controller. The tools can communicate according to the following standard:

Tool

Standard

CTBA & CTBP

WLAN Dual band: 2,4 GHz/5 GHz Standard IEEE 802.11 a/b/g/n

Fig. 2-1: System layout with mPro200GC-AP Fig. 2-2: System layout with mPro400GCD

2.1.1 Tool Data

Feature

Data

Standard

IEEE 802.11a/b/g/n

Safety

WEP-64 HEX

WEP-64 ASCII

WEP-128 HEX

WEP-128 ASCII

WPA/WPA2-PSK TKIP

WPA/WPA2-PSK AES

WPA3-SAE1

WPA3-PEAP1

WPA3-TLS1

802.1x LEAP-TLS WEP-64

802.1x LEAP-TLS WEP-128

802.1x LEAP-TLS TKIP

802.1x LEAP-TLS AES

802.1x EAP-TLS WEP-64

802.1x EAP-TLS WEP-128

802.1x EAP-TLS TKIP

802.1x EAP-TLS AES

Ciso LEAP WEP-64

Ciso LEAP WEP-128

Ciso LEAP TKIP

Ciso LEAP AES

Range

Typically, up to 100 m

Channels

1 – 13 (2,412 – 2,472 GHz)

36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128,

132,136, 140, 149, 153, 157, 161, 165 (5,180 – 5,825 GHz)

Transmission power

20 dBm

1Applies only to CellTek tools with hardware version 2

Integrated

mPro200GC-AP

CellTek tool

(mPro mode)

access point

CellTek tool (mPro mode)

access point

mPro400GCD

System Layout

P2545KA | 2022-12 | REV C

Apex Tool Group

Feature

Data

Sensitivity

-95 dBm (typ. @ 1 Mbps DSSS, 2.4 GHz)

-66.3 dBm (typ. @ 40 MHz MCS7 MM 4K)

-92.5 dBm (typ. @ 6 Mbps OFDM, 5 GHz)

-69.3 dBm (typ. @ 40 MHz MCS7 MM 4K, 5 GHz)

Modulation

CCK/DSSS/OFDM

802.11ac/n Spatial

Streams

2 (2×2 MIMO)

Bluetooth Data Rates Sup-

ported

1, 2, 3 Mbps

Bluetooth Modulation

GFSK@ 1 Mbps

Pi/4-DQPSK@ 2 Mbps

8-DPSK@ 3 Mbps

2.1.2 Country-specific channel settings

The tools work in the license-free 2.4 GHz/5 GHz ISM band.

Band

Channel

Frequency in

GHz

World

Europe

USA/

Canada

World

FCC

2.4 GHz IEEE802.11b/g

2.412

2.417

2.422

2.427

2.432

2.437

2.442

2.447

2.452

2.457

2.462

2.467

–

2.472

–

5 GHz IEEE802.11a

U‑NII‑1

5.180

5.200

5.220

5.240

5 GHz IEEE802.11a

U‑NII‑2

5.260

–

5.280

–

5.300

–

5.320

–

5 GHz IEEE802.11a

U‑NII‑2 ext

100

5.500

–

104

5.520

–

108

5.540

–

112

5.560

–

116

5.580

–

120

5.600

–

System Layout

Apex Tool Group

P2545KA | 2022-12 | REV C

Band

Channel

Frequency in

GHz

World

Europe

USA/

Canada

World

FCC

124

5.620

–

128

5.640

–

132

5.660

–

136

5.680

–

140

5.700

–

Legend

x: Approved and available

-: Not permissible, blocking necessary

o: Permissible with limited power to 20 dBm (SRD)

2.1.3 Cell planning for access point

Each channel operates with a frequency range of 22 MHz. To avoid overlapping the frequency ranges, the

channels must be chosen so that they do not overlap. In other words, a maximum of 3 independent chan-

nels (e.g., 1, 6 and 11) are available in the 2.4 GHz frequency band.

The 5 GHz frequency band provides up to 21 independent channels.

To minimize interference between different radio cells that share the same RF channel, it is advisable to

physically separate them. Note that for multistory buildings, it is necessary to consider both higher and

lower floors.

The following overview shows the basic channel assignment.

Fig. 2-3: Idealized radio cells, the rectangle symbolize the application areas of the tools

The physical circumference of a radio cell depends primarily on the access point used, the antennas and

the type of construction in the surrounding area. The limit of a radio cell is reached when the signal-to-

noise ratio (SNR) falls below 15 dB. If the ratio falls below this value, a new radio cell should be started.

The typical circumference of a radio cell in a building is up to 50 m.

For the tool to be able to connect to different access points automatically (roaming), the SSID and encryp-

tion must be set identically at the corresponding access points.

If wide

-area coverage with controlled emission from multiple access points is required, correspo

nding plan-

ning and evaluation must be carried out for the specific case.

Example installation 5 GHz

•Several overlapping radio cells are possible, even if only one free channel is used.

•Up to 200 tools are then possible within the radio range with a limited volume of data.

•The range of the radio cells is limited by the minimal transmission power.

Channel 1Channel 6Channel 11

System Layout

P2545KA | 2022-12 | REV C

Apex Tool Group

Fig. 2-4: Idealized radio cells = Range of use of the tools, channel 60

2.2 Bluetooth communication

Tool

Standard

CTBA & CTBP

Bluetooth 4.2

SSID 2SSID 3SSID 4SSID 5

SSID 6SSID 7SSID 8SSID 9

Before Initial Operation

Apex Tool Group

P2545KA | 2022-12 | REV C

3 Before Initial Operation

3.1 Requirements

To set up the controller, the following items are required:

•Laptop/PC

•Ethernet cable

•Software S168691 mProRemote Professional

•Software S168688 LiveWire Utilities

•Monitor with VGA connector, keyboard and mouse (optional)

•Micro-B USB cable

3.2 Install Software

1. Download the mProRemote Professional and LiveWire Utilities Software from the follow-

ing website: http://software.apextoolgroup.com/current-software-packages/pc-software/

2. Install the mProRemote Professional software on the PC, see Document S168691 mProRe-

mote Professional.

3. Install the S168688 LiveWire Utilities on the PC, see Document P2372JH.

4. Install the tool driver.

5. Set network settings from laptop/PC to i. e. 192.168.100.201 (if mPro200GC-AP is used).

3.3 Install driver

To be able to configure the tool via the PC software, the tool driver must be installed.

Install tool driver

1. Download the tool driver cellcore-celltek-usb-driver.zip from the following website and un-

pack it: https://software.apextoolgroup.com/current-software-packages/celltek/

2. Connect the tool to the PC via a Micro-B USB cable.

The tool switches on automatically.

3. Open the device manager on the laptop/PC.

Initial operation

P2545KA | 2022-12 | REV C

Apex Tool Group

4 Initial operation

The CellClutch tool and the tightening sequence are configured with the CLPC100 software.

4.1 Configuring the access point

4.1.1 mPro200GC-AP

In the factory setting, the IP address and the subnet mask of the controller are specified with a default

value (Ethernet 1):

Parameter

Default value

IP address

192.168.100.200

Subnet mask

255.255.255.0

Note

IP address conflict

The 200 Series controllers have a factory default IP address of 192.168.100.200. If multiple controllers

are connected to the same network without changing the original IP address, an IP conflict occurs.

►Assign a new, unique IP address to each controller.

Configuring the access point

1. Connect laptop/PC directly to the controller via an Ethernet cable.

2. Start mProRemote Professional on the Laptop/PC.

3. Enter the IP address 192.168.100.200 in the Remote Control tab in the Target input field.

4. Press Remote (TCP/IP).

A connection to the controller is established.

The user interface of the controller opens on the laptop/PC.

5. Select Navigator > Utility > System Settings > Cordless Tools.

6. Open the WLAN AP Configuration.

7. Carry out the desired settings for the configuration of the access point.

8. Press <Apply> to save the changes.

This tab is only displayed for the series mPro200GC(-AP) controller.

Fig. 4-1: WLAN AP Configuration tab

Andere Handbücher für CellTek CTBA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cleco Werkzeuge Handbücher

Cleco

Cleco 75 Series Montage- und Bedienungsanleitung

Cleco

Cleco BB P2055MA Bedienungsanleitung

Cleco

Cleco CellCore CCBA Betriebsanleitung

Cleco

Cleco CellCore CCBPW04Q Bedienungsanleitung

Cleco

Cleco 48CAE15AL3 Bedienungsanleitung

Cleco

Cleco S133410 Bedienungsanleitung

Cleco

Cleco LiveWire 2 17 Series Bedienungsanleitung

Cleco

Cleco NeoTek 30 Series Bedienungsanleitung

Cleco

Cleco BD Series Kurzanleitung

Cleco

Cleco NeoTek 30 Series Bedienungsanleitung

Cleco

Cleco F4-PT-RT-B Bedienungsanleitung

Cleco

Cleco BD Series Bedienungsanleitung

Cleco

Cleco LiveWire 47BA Series Bedienungsanleitung

Cleco

Cleco CellCore CCBA Bedienungsanleitung

Cleco

Cleco CellTek S169263 Betriebsanleitung

Cleco

Cleco 17BP B Bedienungsanleitung

Cleco

Cleco LiveWire 47BS Series Bedienungsanleitung

Cleco

Cleco CellCore Bedienungsanleitung

Cleco

Cleco CellClutch CLBA Series Bedienungsanleitung

Cleco

Cleco 48EAE15AL3 Bedienungsanleitung

Cleco

Cleco LiveWire 47BC Series Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung