Climax VST-1818 Bedienungsanleitung

September 30, 2017

Table of Contents

1. INTRODUCTION ________________________________________________________________________ 2

1.1. FUNCTION OVERVIEW ____________________________________________________________ 2

2. APPLICATION OVERVIEW_______________________________________________________________ 3

2.1. IDENTIFYING THE PARTS __________________________________________________________ 3

2.2. PACKAGE CONTENT _____________________________________________________________ 5

2.3. THE POWER SUPPLY _____________________________________________________________ 5

2.4. SYSTEM REQUIREMENTS __________________________________________________________ 5

3. GETTING STARTED _____________________________________________________________________ 6

3.1. HARDWARE INSTALLATION_________________________________________________________ 6

3.2. SOFTWARE INSTALLATION ________________________________________________________ 12

3.3. FACTORY RESET _______________________________________________________________ 15

4. CONNECTING TO WEBPAGE____________________________________________________________ 17

5. IP CAMERA____________________________________________________________________________ 19

5.1. IMAGE TUNING_________________________________________________________________ 19

5.2. MOTION DETECTION ____________________________________________________________ 19

5.3. TIME STAMP __________________________________________________________________ 23

5.4. STREAM SETTING ______________________________________________________________ 24

5.5. RECORDED FILES ______________________________________________________________ 25

5.6. ALARM SETTING _______________________________________________________________ 26

6. NETWORK SETTING ___________________________________________________________________ 28

6.1. NETWORK____________________________________________________________________ 28

6.2. WIRELESS (WIFI MODELS ONLY) ___________________________________________________ 29

6.3. UPNP_______________________________________________________________________ 31

7. SYSTEM SETTING _____________________________________________________________________ 32

7.1. CHANGE PASSWORD ____________________________________________________________ 32

7.2. REPORT _____________________________________________________________________ 33

7.3. MEDIA UPLOAD ________________________________________________________________ 34

7.4. XMPP ______________________________________________________________________ 35

7.5. DATE &TIME__________________________________________________________________ 36

7.6. DYNAMIC DNS ________________________________________________________________ 37

7.7. FIRMWARE ___________________________________________________________________ 38

7.8. FACTORY RESET _______________________________________________________________ 39

7.9. BACKUP &RESTORE____________________________________________________________ 40

7.10. SYSTEM LOG__________________________________________________________________ 41

7.11. LOGOUT _____________________________________________________________________ 42

7.12. REBOOT _____________________________________________________________________ 42

8. HISTORY ______________________________________________________________________________ 43

8.1. EVENT LOG___________________________________________________________________ 43

8.2. REPORTED EVENTS_____________________________________________________________ 43

9. NETWORK VIDEO RECORDER__________________________________________________________ 44

10. REMOTE ACCESS TO THE IP CAMERA __________________________________________________ 47

10.1. HOME PORTAL SERVER__________________________________________________________ 47

10.2. PORT FORWARDING_____________________________________________________________ 48

11. CONNECTING TO CLIMAX CONTROL PANELS___________________________________________ 53

11.1. LEARNING THE IP CAMERA INTO THE CONTROL PANELS __________________________________ 53

11.2. SURVEILLANCE AND SETTING______________________________________________________ 56

11.3. OPERATION___________________________________________________________________ 60

11.4. HOME PORTAL SERVER__________________________________________________________ 63

12. APPENDIX_____________________________________________________________________________ 63

12.1. CONTACT ID EVENT CODE________________________________________________________ 63

1. Introduction

The VST-1818 IP Camera provides a quick and accurate surveillance solution to protect

your surroundings. You can watch these live-stream videos through MJPG or H264

formats via Local Area Network, or online remotely using port forwarding, or via the

Climax Home Portal™Server for you to easily keep track of the safety of your homes or

businesses.

VST-1818 IP Camera can be further integrated into your current Climax Security Control

Panels to form a complete security system, and capture video when an alarm is

activated.

VST-1818 IP Camera series includes the following models with different functions and

spec:

Indoor/Outdoor

Wi-Fi

IR LED

IR Cut Filter

VST-1818

Indoor

Yes

VST-1818-WI

Indoor

Internal Antenna

Yes

VST-1818-WE

Indoor

External Antenna

Yes

VST-1818L-WI

Indoor

Internal Antenna

VST-1818LR-WI

Indoor

Internal Antenna

Yes

VST-1818SLIM

Indoor

1.1. Function Overview

The VST-1818 IP Camera includes a variety of functions that can be adjusted to suit

different necessities. Below is an overview of the functions of the IP Camera:

- Alarm-triggered video recording that includes Pre-alarm recording to see how alarm

was triggered. Please see 5. IP Camera, 5.6. Alarm Setting.

- 24-hour HD video recording. Please see 9. Network Video Recorder.

- Remote access/control on Climax Home Portal Server on a web-enabled device.

Please see 10. Remote Access to the IP Camera, 10.1. Home Portal Server.

- Remote video using Port Forwarding. Please see 10. Remote Access to the IP

Camera, 10.2. Port Forwarding.

- Surveillance when complementing with Control Panels. Please see 11. Connecting

to the Climax Control Panels, 11.2. Surveillance and Setting.

- Remote access/control complementing with Control Panels on Climax Home Portal

Server on a web-enabled device. Please see 11. Connecting to the Climax

Control Panels, 11.4. Home Portal Server.

2.Application Overview

2.1. Identifying the Parts

VST-1818/VST-1818WE/VST-1818WI/VST-1818L-WI/VST-1818LR-WI

1. IP Camera Lens

2. Microphone

3. Optical Sensor

4. Power LED (Green)

On: powered

Off: unpowered

5. Warning LED (Red)

Flashes for 2-3 seconds: Activating WPS protocol

Flashes 3 times: WPS pairing successful

Flashes twice: Enter/exit privacy mode

On: The IP Camera is in privacy mode

6. Internet-Connection LED (Blue)

On: connected to internet (wired or wireless)

Off: disconnected from internet

Flashes for 5 minutes: The IP Camera is in learning mode

Flashes quickly: The IP Camera is streaming or recording.

7. Speaker

8. WPS Button

9. Privacy Button

Press and hold for 2 seconds until warning LED flashes twice, let go to enter or exit privacy

mode

Press and hold for 10 seconds to enter learning mode

Press and hold for 6 seconds to exit learning mode.

10.Expandable Micro SD card slot

Compatible with Micro SD card up to 32GB storage capacity (Micro SD card is not

included by factory default)

11.Ethernet Cable Port

12.DC Jack (5V DC, 2A input)

13.Camera Stand Mounting Hole

14.Antenna (VST-1818WE model only)

VST-1818 SLIM

1. WPS Button

2. Privacy Button

Press and hold for 2 seconds until warning LED flashes twice, let go to enter or exit privacy

mode

Press and hold for 10 seconds to enter learning code

Press and hold for 6 seconds to exit learning mode

3. Microphone

4. Power LED (Green)

On: powered

Off: unpowered

5. Warning LED (Red)

Flashes for 2-3 seconds: Activating WPS protocol

Flashes 3 times: WPS pairing successful

Flashes twice: Enter or exit privacy mode

On: The IP Camera is in privacy mode

6. Internet-Connection LED (Blue)

On: connected to internet (wired or wireless)

Off: disconnected from internet

Flashes for 5 minutes: The IP Camera is in learning mode.

Flashes quickly: The IP Camera is streaming or recording.

7. IP Camera Lens

8. Expandable Micro-SD slot

Compatible with Micro SD card up to 32GB storage capacity (Micro SD card is not

included by factory default)

9. Ethernet Cable Port

10.DC Jack (5V DC, 2A input)

11.Camera Stand Mounting Hole

2.2. Package Content

The VST-1818 IP Camera is packed in a white box that includes:

-An Ethernet cable

-A power supply (5V DC 1A adapter)

-An IP Camera Stand

-Installer CD

2.3. The Power Supply

An AC power adapter is required to connect to a wall outlet. Be sure only to use an

adapter with the appropriate AC voltage rating to prevent component damage. A 5V DC

output and 1A adapter is generally used to power the IP Camera.

2.4. System Requirements

The system requires a TCP/IP network environment.

To install the CD Wizard, your computer must have:

Microsoft Windows 98, ME, NT4.0, 2000, XP, Vista, 7 or 8 operating system. A

Mac or Linux based machine is also compatible.

DirectX 9.0 or later Internet Explorer 6.x or later

CD-ROM drive

Pentium III CPU 500 MHz or higher, or equivalent AMD

128 MB RAM

Graphics card: 32 MB RAM

3.Getting Started

Read this section of the manual to learn how to set up your VST-1818 IP Camera and

program system settings over the Web page.

With a valid internet connection, this system can bring you the freedom to access and

control your IP Camera anywhere and anytime in the world.

3.1. Hardware Installation

Step 1. Remove any plastic cover and prepare the enclosed adapter and Ethernet

cables.

With Wired Connection:

Step 2. Find a suitable location to mount the IP Camera.

Step 3. Plug in the enclosed Ethernet cable.

<NOTE>

If the IP Camera is to complement with a Control Panel, connect the IP Camera

and the Control Panel to the same router to learn the IP Camera into the Control

Panel. Please refer to 11. Connecting to the Climax Control Panels if you

wish to increase the functionality of the IP Camera.

Step 4. Plug in the adapter.

With Wi-Fi (Wireless) Connection:

Please refer to the 6. Network Setting. 6.2. Wireless on how to connect to the Wi-Fi

Network.

Using a Camera Stand

Below displays the 3 part design of the camera stand:

The Base is attached to the surface where

the stand is mounted

The Shaft is connected between

the base and the head.

The Head connects the IP Camera

to the whole camera stand

Below outlines the steps to mount the IP Camera to a surface.

Step 1. Find a surface to mount the camera stand. Locate the 2 mounting holes of the

Base and use them as template, mark the surface.

Step 2. Apply wall plugs if fixing onto plaster or brick. Screw the Base onto the surface.

Step 3. Attach the Head to the Shaft by rotating the Head clockwise onto the Shaft.

Step 4. Attach the Shaft onto the Base by rotating the Shaft clockwise onto the Base.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Climax IP-Kamera Handbücher

Climax

Climax Vesta Series Benutzerhandbuch

Beliebte IP-Kamera Handbücher anderer Marken

FLIR

FLIR Exx series Bedienungsanleitung

Avigilon

Avigilon H4A-BO1-IR Bedienungsanleitung

Digital Watchdog

Digital Watchdog DWCA-C128-64 Bedienungsanleitung

ShareTech

ShareTech AV1 Bedienungsanleitung

Ezviz

Ezviz C6C Bedienungsanleitung

Melchioni

Melchioni UCAM 2015 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4630 Bedienungsanleitung

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Bedienungsanleitung

Mitel

Mitel 6800i Series Service-Handbuch

Vitek

Vitek VTC-IR403-212NP Bedienungsanleitung

THOMSON

THOMSON DSC - 323W Bedienungsanleitung

AVer

AVer FB2027 Bedienungsanleitung

ENFORCER

ENFORCER EV-T5105-N2SQ Bedienungsanleitung

Wansview

Wansview NC543 Bedienungsanleitung

Eneo

Eneo MCB-64A0003M0A Bedienungsanleitung

deView electronics

deView electronics CBDNI36F Bedienungsanleitung

Swann

Swann SwannEye Bedienungsanleitung

LevelOne

LevelOne IP CamSecure Bedienungsanleitung