CM FG10 Bedienungsanleitung

Floor Grinder

Operating Manual

Model # DFG-250E

Item # 1211250E

Please read these instructions carefully before using.

Page Number

Contents

Introduction and Description

Technical Data

Operation

Safety Precautions

Troubleshooting

Maintenance

Parts Diagram

Parts List

8-9

Introduction and Description

This manual is intended to provide operation and service information

necessary for the safe and efficient use of the Virginia Abrasives Floor

Grinder.Operating or servicing the unit other than in accordance with the

instructions given may subject the machine to conditions beyond its capability.

This may result in the machine failure or personal injury.

IMPORTANT:

Read the entire operating manual carefully before attempting to use the floor

grinder. Special attention should be given to the section entitled “Safety

Precautions”.

The floor grinder is a sturdy, reliable and easy to use machine.

The floor grinder is fitted with a 1.5 hp single phase motor.This motor offers a

direct drive to the grinding plate by way of a flexible coupling between the

motor and the plate.

The shroud system is unique in design by automatically adjusting to suit

segment height and floor angle.This shroud system when used in conjunction

with an appropriate industrial vacuum unit helps eliminate dust during grinding.

The shroud has 2 removable sections to allow the operator to maneuver the

grinder close to the wall.Please note that fugitive dust will likely occur when

using the

grinder with the two shroud sections removed.

The floor grinder comes complete with a water connection for wet grinding, if

required.The water connection incorporates a ball valve that allows the

operator to regulate the water supply to obtain the best grinding results.

The floor grinder has a foldable handle which enables it to be easily

transported in the trunk of most vehicles.The rear wheels can be extended

outward for added stability during use.The operator can raise or lower the

height of the handle to maximize comfort.

The newly designed lifting handle system makes the machine easy to lift.

1.5

1.1

1730

surface (use the bubble-level on the machine as a reference).

5.Check that all nuts and bolts on the folding handle latch are tight and secure.

6.Raise the grinding plates from the floor.

7.Start the motor by pressing the black switch on the starter box.

8.Lower the grinding plate and begin grinding. Keep the grinding head

moving side to side on the work surface to create an evenly ground surface

until the desired results are reached.

Stopping the Grinder

Depress the red stop button on the start box.

Note:

The position of the axle may be adjusted as needed for leveling.

1.Adjust the vertical grinding position by loosening the level adjustment

fastener counter clockwise.

2.Lifting the level adjustment handle raises the back end of the grinder.

3.Lowering the level adjustment handle lowers the back end of the grinder.

4.Use “bubble-level”, mounted on the machine as a reference.

5.Secure desired grinder position by tightening the level adjustment fastener

Clockwise.

Safety Precautions

The Bycon Floor Grinder has been designed to minimize noise, vibration levels

and to provide maximum operator safety. However, incorrect use of the

grinder may cause serious injury and therefore the following precautions must

be taken:

1.Do not use the grinder for longer than prescribed in your local environmental

working regulations, as the noise load from extensive daily use may result in

hearing damage.

2.Always use hearing protection, goggles, gloves and appropriate footwear.

3.Do not modify the grinder in any manner. Do not use a machine that has

been modified by anyone other than the manufacturer or authorized dealers.

4.Do not add weight to the machine. Use different grinding plates to achieve

the desired grinding performance.

5.Do not operate the grinder with the grinding head raised any higher than

necessary. i.e. tipped back on handle.

6.Always be sure that folding handle latch is secure and has not become

loose during use.

7.During normal use the machine is exposed to vibration. Occasionally

check machine for bolts/nuts which may have vibrated loose.

8.Do not allow water or flammable materials to enter the interior of the

Motor.

Respirable Silica Dust Warning

Grinding/cutting/drilling of masonry, concrete,metaland other materials can

generate dust,mists and fumes containing chemicals known to cause serious

or fatal injury or illness, such as respiratory disease,cancer,birth defects or

other reproductive harm.If you are unfamiliar with the risks associated with the

particular process and/or material being cut or the composition of the tool

being used, review the Safety Data Sheets (SDS) and/or consult your

employer, the manufacturers/suppliers, governmental agencies such as OSHA

and NIOSH and other sources on hazardous materials.

Use engineering controls to control dust, mist and fumes at the source

wherever possible.Use good work practices and follow the recommendations

of the manufacturers/suppliers, OSHA/NIOSH, and occupational and trade

associations.Water should be used for dust suppression when wet

grinding/cutting/drilling is feasible.When the hazards from inhalation of dust,

mists and fumes cannot be eliminated,the operator and any bystanders should

always wear a respirator approved by NIOSH/MSHA for the material being

used.

Grinding/cutting/drilling of masonry, concrete and other materials containing

silica may generate dust or mists containing crystalline silica.Silica is a basic

component of sand, quartz, brick clay, granite and numerous other minerals

and rocks.Repeated and/or substantial inhalation of airborne crystalline silica

can cause serious or fatal respiratory diseases, including silicosis.The state of

California and other authorities have listed respirable crystalline silica as a

substance known to cause cancer.When grinding/cutting/drilling such

materials, always follow the respiratory precautions mentioned above.

Troubleshooting

Symptom

Possible Cause

Action

Grinder runs for short time

then stops

The electrical power

current limit screw is not

adjusted properly

Adjust the current limit

screw located in the

Schneider housing to the

appropriate setting.

Grinder runs but does not

perform adequately.

Tooling is not matched to

the application

Re-evaluate tooling

selection.

Grinder vibrates during use

Grinding plates not

correctly balanced

Replace grinding plates.

Grinding noise coming from

grinding head under no-load

operation.

Worn motor bearings or

drive coupling

Have machine evaluated

and serviced by authorized

service professional

Maintenance

Daily cleaning: The motor should always be kept clean. No water, or foreign

materials should be allowed to get into the interior of the motor.

Check operating amperage draw: While the motor is in operation, take care to

keep the operating amperage below maximum level.

Operational sounds: During operation of the motor there must be no rubbing

sounds, squeals or other random noises. Stop the motor immediately and restart

after inspection and corrections have been made.

Parts Diagram

NO. Code Description Drawing No. Qty

1.FG10-001 Handle 2

2.FG10-002 Upper arm SHMDJ71501 1

3.FG10-003 Switch assembly 1

4.FG10-004 Plug wire 1

5.FG10-005 Power wire 1

6.FG10-006 Electric motor 1

7.FG10-007 Motor carry Handle SHMDJ71508 1

8.FG10-008 M6X16 hexagon screws 4

9.FG10-009 Motor ﬁxed mount SHMDJ71513 1

10 .FG10-010 Motor connection plate SHMDJ71510 1

Check the security of the adjustable folding handle latch periodically. The wheel

bearings use sealed bearings and require no regular greasing.

11 .FG10-011 Ф10 Flat washers 1

12 .FG10-012 M8X25 hex screw 4

13 .FG10-013 Dust shroud SHMDJ71504 1

14 .FG10-014 M12X25 socket hexagon screw 2

15 .FG10-015 Detachable shroud SHMDJ71505 1

16 .FG10-016 Shroud plastic wear strip set（long）1

17 .FG10-017 Shroud plastic wear strip set（short）1

18 .FG10-018 motor driving sleeve SHMDJ71503 1

19 .FG10-019 M10X30 hex screw 1

20 .FG10-020 M10 nuts 2

21 .FG10-021 Ф10 Flat washers 2

22 .FG10-022 ﬂex coupling-Morse SHMDJ71509 1

23 .FG10-023 M10X55 hex screw 2

24 .FG10-024 M10X55 socket hexagon screw 2

25 .FG10-025 connection disc SHMDJ71511 1

.FG10-026 M8X12 socket hexagon screw 3

.FG10-026A 3/8”-24 x 3/4" socket hexagon screw For G-Head 4

27 .FG10-027 Dowel disc SHMDJ71514 1

28 .FG10-028 Flexible conduit SHMDJ71515 1

29 .FG10-029 ClipФ60 2

30 .FG10-030 M10X30 hex screw 2

31 .FG10-031 Ф10 Flat washers 2

32 .FG10-032 Wheel 2

33 .FG10-033 M8X12 hexagon screws 2

34 .FG10-034 Lift lever SHMDJ71507 1

35 .FG10-035 Eccentric shaft SHMDJ71506 1

36 .FG10-036 M12 locking screws 1

37 .FG10-037 cooling water pipe SHMDJ71516 1

38 .FG10-038 Frame body part SHMDJ71502 1

39 .FG10-039 M10 nuts 2

40 .FG10-040 Ф10 Flat washers 2

41 .FG10-041 Connection sets SHMDJ71512 2

42 .FG10-042 M12X25 Round socket hexagon screw 2

43 .FG10-043 adjust handle 1

44 .FG10-044 M8X20 hexagon screws 2

45 .FG10-045 Positioning clamping claw buckle SHMDJ71510 1

46 .FG10-046 Level bubble 1

Inhaltsverzeichnis

Andere CM Bodenreinigungsmaschine Handbücher

CM FG10Pro Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch