Cobra LI-6050 Bedienungsanleitung

LI-6050 Alignment instructions

WARNING

Any repairs or adjustments should be made under the supervision of a

qualified radiotelephone technician.

I TRANSMITTER

1.Power Supply Voltage

The Power supply voltage should be set for 8.4VDC measured at the radio

during transmit. Periodically check the power supply voltage during the

alignment procedure.

2.Frequency Setting

A. Connect a frequency counter or Communications Service Monitor to the

Antenna through an RF power attenuator (10 watt minimum rating,

20 dB minimum attenuation).

B. Depress the PTT switch.

C. Adjust the VC1 trimmer capacitor such that the output frequency is

equal to the channel frequency with a maximum error of +/- 200 Hz.

D. Release the PTT switch.

3. Output Power Alignment.

A. Set the power supply voltage for 8.4VDC.

B. Connect a Communications Service Monitor or a wattmeter and dummy load

to the antenna connector.

C. Depress the PTT switch.

D. To be convinced for HI:3.0 Watt output power with a maximum Limit of +/-0.2Watt.

E. To be convinced for MED:2.0 Watt output power with a maximum Limit f +/-0.2Watt

F. To be convinced for LOW 0.5 Watt output power with a maximum Limit 400-800 mWatt

E. Release the PTT switch.

4. Deviation Adjustment.

A. Connect an audio generator to the microphone jack(JK1). The audio frequency

Should be set at 1 KHz.

B. Connect an FM deviation meter or Communications Service Monitor to the

antenna connector through an RF power attenuator (10 watt minimum rating,

20 dB minimum attenuation). Set the monitor to read peak deviation.

C. Depress the PTT switch.

D. Adjust the audio generator level 100 mV rms.

E. Changing R57 parameter for +/- 2.3 KHz maximum deviation. (With CTCSS tone)

F: Changing R64 parameter for +/- 2.3 KHz maximum deviation. (With DCS Code)

G. To be convinced +/- 1.9KHz without CTCSS tone or DCS code.(1.5KHz dev. 20dB up)

H. Release the PTT switch.

II RECEIVER

NOTE:

Insure that the proper channel has been selected before preceding with the

alignment procedure.

1. Power Supply Voltage

The proper voltage for testing is 8.4 VDC.

2. Receiver Alignment

A. Connect an RF signal generator or Communications Service Monitor to the

antenna connector.

B. Connect a SINAD meter and oscilloscope across the speaker terminals.

C. Set the output level of the RF signal generator for -47 dBm. The generator should

be set for +/- 1.5 KHz deviation of a 1 KHz tone.

D. Set the audio output level for 0.6 Vrms. by adjusting volume.

E. Reduce the output level of the RF signal generator for produce a 6-12 dB

SINAD indication.

F: educe RF output level to equal or less than –119dBm with condition of SIND=12Db

III. WEATHER:

1. Power Supply Voltage

The proper voltage for testing is 8.4 VDC

2 weather

Alignment:

A. Connect an RF signal generator or Communications Service Monitor to the

antenna connector.

B.Connect a SINAD meter and oscilloscope across the speaker terminals.

C.Set the output level of the RF signal generator for -47 dBm. The generator should

be set for +/- 3 KHz deviation of a 1 KHz tone.

D.Set the audio output level for 0.6 Vrms. by adjusting volume.

E: educe RF output level to equal or less than –119dBm with condition of SIND=12Db.

Inhaltsverzeichnis

Andere Cobra Transceiver Handbücher

Cobra

Cobra 29 LTD ST Bedienungsanleitung

Cobra

Cobra 29 LX LE Betriebsanleitung

Cobra

Cobra MR HH600W FLT GPS BT Bedienungsanleitung

Cobra

Cobra MR F77W GPS Bedienungsanleitung

Cobra

Cobra 29 LX LE Bedienungsanleitung

Cobra

Cobra MARINE MR HH330 FLT EU Bedienungsanleitung

Cobra

Cobra 29 LX LE Referenzhandbuch

Cobra

Cobra 19 MINI Bedienungsanleitung

Cobra

Cobra MR HH475 FLT BT Gebrauchsanweisung

Cobra

Cobra MR HH425 LI VP Gebrauchsanweisung

Cobra

Cobra MR HH325VP Bedienungsanleitung

Cobra

Cobra MR HH425LI VP Bedienungsanleitung

Cobra

Cobra MR HH475 FLT BT/EU Bedienungsanleitung

Cobra

Cobra MR HH500 FLT BT Bedienungsanleitung

Cobra

Cobra 29 LX LE Bedienungsanleitung

Cobra

Cobra 19 Ultra III Bedienungsanleitung

Cobra

Cobra 29 WX NW BT Betriebsanleitung

Cobra

Cobra 19 DX IV Bedienungsanleitung

Cobra

Cobra FRS.200 Bedienungsanleitung

Cobra

Cobra 19 DX IV Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung