Code Alarm PC 7500 Bedienungsanleitung

Owner's Manual

Remote Vehicle Control System

IMPORTANT NOTE:The operation of the Power Code as described in this

manual is applicable to most vehicles. However, due to the engine type

and configuration of some vehicles (i.e. diesel engines), some functions

AND/OR SAFETY PRECAUTIONS may not apply.Please see your

installing dealer for more information.

PC 7500

Car Start,Security and

Convenience System

101516-3

Table of Contents

Features and Benefits of the PowerCode PC 7500TM ..................... 4

Using Your Remote Transmitter .............................................. 5

Arming the Security System

Pre-arm Mode

Disarming the Security System

Attempted Intrusion Identification

Disabling the IT-sTM InteriorTheft Sensor ............................... 6

Two-Stage Door Unlock

Activating the Trunk Release Feature

Turning on the Vehicle Headlights

AUX 3

Using the Car Finder Feature

Personal Protection Alarm (Panic)

Remote Start / Stop Feature

Using Valet Mode

UsingYour Remote Starter ...................................................... 7

Starting Your Vehicle

If your vehicle stalls or does not start

Remote Start Safety Features

Entering the Vehicle While it is Running via Remote Start

Pre-Heating or Pre-Cooling the Interior of the Vehicle

Turning on the Rear-Window Defroster

Using the “Quick-stop” Feature

Automatic Convenience Options ............................................ 7

WhenYour Security System isTriggered ............................... 8

The Interior Status Indicator .................................................... 9

System Maintenance ................................................................ 9

Changing the Remote Control Battery

Adding Remote Controls to Your System

Deleting Lost or Stolen Remote Controls from Your System

BasicTroubleshooting ............................................................ 10

Emergency Disarm Procedure .......................................... 11

Emergency Disarm Button Location

Installer Programmed Options

Your Code-Systems,Inc.Limited LifetimeWarranty...................12

Code AlarmTheft Protection Plan .............................................13

Features and Benefits of the Power Elite PC 7500

Two Easy-to-Use Weather-Resistant Remote Controls

The remote controls included with the PowerCode PC 7500TM utilize

durable, moisture resistant cases and sealed rubber buttons for

reliability and long life. Rolling code technology prevents the

transmitter signals from being duplicated. The button functions are

clearly labeled to make the PowerCode PC 7500TM simple to operate.

All Entrances Protected

Opening any door or entrance protected by the security system

triggers the alarm’s 125db siren (or vehicle horn) and flashes the

vehicle parking lights.

Starter Disable

The PowerCode PC 7500TM protects your vehicle from theft by

disabling the starter when the system is armed.

IT-s

InteriorTheft Sensor

This patented sensor uses infra-red technology to reliably detect

vehicle impact associated with attempted intrusion. The IT-sTM

sensor guards against vehicle body damage, and theft of the

vehicle’s equipment (such as airbags) and personal belongings.

Remote Keyless Entry

The PowerCode PC 7500TM conveniently locks and unlocks vehicle

doors and opens the trunk or hatch by remote control.*

Personal Protection Features

Remote Panic Alarm, Headlight control, Illuminated Entry,

and Car Finder are among an array of features that enhance

personal safety.**May require additional components and/or charges.

Interior Status Indicator

The bright-red warning light is an effective visual deterrent to a

would-be thief.

Remote Start

The PowerCode PC 7500TM allows you to warm up your vehicle

and preheat or pre-cool the interior with the press of a button on

the remote control.

PowerRange

Antenna

This long-range antenna allows you to operate the PowerCode PC

7500TM from distances of up to1/8mile. Remote-start your vehicle

from the safety of your home, apartment or office building.

E-Code Coded Override System

If this feature is enabled, it will allow you to enter a personal 4-digit

code that only you will know. This will be used for overriding the

system in the case of an emergency or a lost transmitter.

* If vehicle is equipped with power door locks and they are connected to the alarm system by your installer.

Press to ARM the Security

System and Lock Doors

Press for Car Finder

Press and Hold for

Panic Alarm

Press to DISARM Security

System and Unlock Doors

Press TWICE for Two-Stage

Door Unlock*

PressandHoldto OpenTrunk

Press ARM, then press

START for 2 seconds

Press TWICE to turn on

Rear Defroster*

Arming the Security System

To arm the system, exit the vehicle, close all doors, then press* the

ARM button. The siren** will “chirp” twice†and the parking lights will

flash twice, indicating the system is armed. The doors will also lock at

this time (if equipped and connected). The status indicator (red

warning light on the dash) will blink steadily, once per second.

Pre-arm Mode

If the siren chirps and the parking lights flash only once, this indicates

that the vehicle courtesy light is on, or that an entrance is not closed

securely. Check to see that doors, hood, and trunk are properly

closed. Once all entrances are secured (and the courtesy light is off),

the system will chirp / flash again.The system is now fully armed.

(If the entrance is not secured within 5 minutes, the system will arm

and ignore the unsecured entrance until it is closed.)

Disarming the Security System

To disarm the system, press the DISARM button.The siren will chirp

and the parking lights will flash once, and the doors will unlock.

The courtesy light will turn on for 1 minute, or until the vehicle is started.

Attempted Intrusion Identification

If the siren chirps four times when disarming, this indicates that the

system was triggered in your absence. The status indicator will also

flash rapidly. Perform the following operation to determine the protected

zone that triggered the system:

After disarming, press the

emergency override button.

The siren will chirp to indicate

the cause of the alarm trigger:

1 chirp IT-sTM Interior Theft Sensor

2 chirps Door

3 chirps Hood

4 chirps Trunk/Optional Sensors

5 chirps Ignition was turned on

Using Your Remote Transmitter

Press for two-car

operation (SHIFT)

Pressand hold to turn

on headlights

Press to Activate

Auxiliary Function

* Throughoutthis manual, ‘press’ refers topressing

forless than 1second; ‘press and hold’ refersto pressing for morethan 1 second.

** ’Siren’ also refers to the vehicle horn if it is used as the alarm sounding device.*

†Ifyou have chosenthe Silent Arming Option, thesiren will notsound when arming or disarminguntil the

appropriatebutton ispressed asecond time.

Using Your Remote Transmitter

(cont.)

Disabling the IT-s

InteriorTheft Sensor

It may be necessary at times to disable the IT-sTM Interior Theft Sensor,

especially when parking in areas (like parking garages) where

extreme vibration may cause false alarms. Press the ARM button and

then press the FIND/PANIC button within two seconds of pressing

ARM to disable the interior theft sensor.The siren will chirp three times

to indicate that the sensor is disabled.The sensor will become

enabled again the next time the system is armed normally.

Two-Stage Door Unlock

If this feature is enabled on your system, pressing DISARM one time

will unlock only the driver’s door. Press DISARM again within 1 minute

to unlock all doors.

Activating theTrunk Release Feature

Press and hold TRUNK to open the vehicle trunk or hatch (if equipped

and connected). If this button is used to operate another accessory,

the accessory will stay active for as long as the button is held.

Turning on theVehicle Headlights

Press and hold the LIGHTS button to turn on the vehicle headlights.

(The alarm system will attempt to arm if not already armed, unless it is

in Valet mode.) The lights will stay on for 20 seconds, or until LIGHTS

is pressed again.

Using AUX 3

If this feature is enabled on your system, pressing AUX for 1 second

will activte the auxilliary function.

Using the Progressive Car Finder Feature

Press FIND on the remote control to locate your vehicle.The siren will

emit five short chirps at low volume, increasing in volume each of

three times the button is pressed.

Personal Protection Alarm (Panic)

Press and hold the PANIC button to activate the vehicle siren and

parking lights for 30 seconds. (If the vehicle horn is connected, the

horn will “pulse” for 30 seconds.) Press any remote control button to

turn off the Panic alarm.

Remote Start / Stop Feature

Press ARM, then press START within 2 seconds on the remote control.

If all safety parameters are correct, the engine will start within 5 seconds

(diesel engines will take longer.) Press and hold START again to turn

off the vehicle. (Turn to page 6 for more on remote start features.)

Using Second Car Mode

If this feature is enabled, one transmitter will control two vehicles

equipped with a PowerCodeTM system. To operate the second vehicle,

press the shift button, then within two seconds, press the desired

function button.

UsingValet Mode

If the Passive Arming feature is enabled on your system, Valet mode

temporarily prevents the alarm system from arming automatically.

This is useful when fueling or servicing your vehicle.

To enterValet Mode:

With the vehicle ignition on, press the ARM button. The red dashboard

warning light (status indicator) will turn on for one second, then turn

off.This indicates that the system is in Valet mode.Once the ignition is

turned off, the status indicator will emit a quick double-flash pattern.

Note: In Valet mode, all keyless entry, convenience and remote start

features operate normally.

To exitValet Mode:

With the vehicle ignition on, press the DISARM button. The red

dashboard warning light (status indicator) will turn on for one second,

then turn off.This indicates that the system has exited Valet mode.

Hint: To prevent your security system from automatically arming while

unloading or refueling your vehicle, without placing the system in

Valet mode, simply press the disarm button on your remote control

transmitter after turning the ignition key off. Doing so places your

system into a temporary or onetime Valet mode. Next time you exit

your vehicle the system will arm in the normal manner.

UsingYour Remote Starter

StartingYourVehicle

The remote start function is activated by pressing the ARM button,

then pressing the START button on the remote control within 2

seconds.The system will check the vehicle to ensure that it is safe to

start, and if all safety parameters are correct, the engine will start

within 5 seconds (diesel engines will take longer.) Press and hold

START again to turn off the vehicle.

If your vehicle stalls or does not start...

If the vehicle stalls or does not start, the Power Code PC 7500TM will

pause 5 seconds, then try 3 more times to start the vehicle (a total of

four attempts).The system pauses 5 seconds between each start

attempt. If the vehicle does not start after the fourth attempt, the Power

Code PC 7500TM will abort the start process.

Your vehicle can be started by remote control whether the alarm is

armed or disarmed. When the alarm is armed, the impact sensor turns

off when the vehicle is started to prevent the engine vibration from

setting off the alarm.

Using Your Remote Transmitter

(cont.)

UsingYour Remote Starter

(cont’d)

Remote Start Safety Features

For safety and security reasons, the PowerCode PC 7500TM will shut

off the vehicle during remote start if any of the following occur:

• The vehicle hood is opened

• The brake is pressed before the vehicle ignition is turned on

with the key

• The engine reaches 3 times its normal idle*

• The alarm is triggered

As a safety precaution, the vehicle will shut off if left unattended for 12

or 24 minutes, depending on the time preset by your installer.

Entering theVehicleWhile It is Running via Remote Start

1.Press DISARM to unlock the door(s) and turn off the alarm

system (if it is not already off).

2.Enter the vehicle. Do not press the brake pedal.

3.Insert the key into the ignition and turn to the ON position.

4.Press the brake pedal. The remote starter disengages and the

vehicle will operate normally.

Pre-Heating or Pre-Cooling the Interior of theVehicle

Before exiting the vehicle, set the temperature controls to the desired

setting and operation. After the Power CodeTM starts the vehicle, the

heater or air-conditioning will activate and heat or cool the interior to

your setting.

Turning on the Rear-Window Defroster (if connected)

While the vehicle is running via remote start, press DEFRST on the

remote control. The vehicle defroster will activate and run for 10

minutes, or for your vehicle’s preset time limit.

Using the“Quick-stop”Feature

If you want to make a short stop and leave your vehicle running (to keep

the interior warm or cool, for instance), the quick stop feature allows

you to do this while keeping your vehicle secure and your keys with you.

To engage quick stop:

1.Stop the vehicle and place the transmission in PARK.

2.With your foot off the brake pedal, press the press the START

button on the remote control within 2 seconds

The parking lights will turn on, indicating that the vehicle is now

running via remote start.

3.Remove the keys from the ignition and exit the vehicle. Press

ARM to arm the alarm system if desired.

Note: Do not leave children or animals unattended in the vehicle

when using the quick stop feature.

Automatic Convenience Options

The Power Code PC 7500TM performs a variety of automatic functions to

enhance security and comfort. Some of these features are programmable

at the time of installation. Please see your installer for further details.

Illuminated Entry

When the alarm system is disarmed, the vehicle courtesy lights will turn

on for 1 minute, or until the vehicle is started or the system is re-armed.

Illuminated Exit

When removing the key from the ignition, the vehicle courtesy lights

will turn on for 1 minute, or until the Power Code PC 7500TM is armed.

Automatic Arming

The Power Code PC 7500TM will arm automatically 1 minute after the

key is removed from the ignition. This feature can be temporarily

disabled by placing the system into Valet mode.

Ignition Lock

If all doors are closed and the vehicle is started with the key, the doors

will automatically lock.

Ignition Unlock

When removing the key from the ignition, the doors will automatically unlock.

WhenYour Security System is Triggered

The Power Code PC 7500TM will trigger if one of the following events

occurs while the system is armed:

• Any protected entrance is opened

• The vehicle ignition is turned on

• The vehicle is jolted hard enough to signal the impact detector

Once the alarm is triggered, the siren (or horn) sounds and the vehicle

parking lights flash for 30 seconds.The system will then re-arm, awaiting the

next intrusion attempt.To stop the siren while keeping the alarm armed

and doors locked, press the ARM button while the system is triggered.

The Interior Status Indicator

The Status Indicator is a high-intensity red light mounted in a visible

location on the vehicle dashboard.This red light gives a visual indication

of the alarm system’s state of operation. Note the chart below:

If the Status Indicator is... ....then the Security System

Flashing Green is disarmed

Flashing Slowly is armed

Flashing Very Quickly was triggered in your absence

(see Attempted Intrusion ID - page 4)

Flashing Intermittently is in Valet mode(LED is Green)

(2 flashes, off, 2 flashes)

On (not flashing) is in Pre-arm mode

System Maintenance

Changing the Remote Control Battery

The two 3-v lithium batteries (CR2016) supplied in your remote control

should last approximately one year, depending on usage. When the

battery begins to weaken, you will notice a decrease in range, or the

distance from your vehicle that your remote transmitter will operate.

Follow the instructions below to change the remote transmitter battery.

1.Insert the edge of a coin into the slot at the side of the remote

control.Twist the coin to pry the remote control halves apart.

2.Remove the old batteries and replace with new ones. Be sure

to observe the (+) and (-) signs in the battery compartment.

3.Carefully snap the case halves back together, then test the

remote control.

Adding Remote Controls toYour System

The Power Code PC 7500TMhas the ability to operate from up to eight

(8) remote controls. Follow these instructions to add a remote control

to your system.

1.Make sure the security system is disarmed and the ignition is off.

2.Open the driver’s door.

3.Turn vehicle ignition on.

4.Press and hold emergency override button.

After 15 seconds, the siren or horn will sound three (3) times.

This indicates that the unit has entered the remote control

programming mode.

5.Release the button.

6.Press the ARM button (button 1) on the remote control to be

programmed.

The siren or horn will sound once, indicating that the system

has “learned” that remote control.

7.Repeat step 6 for any additional remote controls.

8.Turn the vehicle ignition off to exit the programming mode.Test

all remote controls to ensure that they work properly.

Basic Troubleshooting

This section outlines some of the basic issues you may experience

while becoming used to the Power Elite PC 7500TM. If you have a

problem that is not covered by this section, please consult your installer.

motpmySmotpmySmotpmySmotpmySmotpmyS melborPmelborPmelborPmelborPmelborP noituloSnoituloSnoituloSnoituloSnoituloS

seodlortnocetomeRkrowton

yrettabdaedrokaeW

tonlortnocetomeR demmargorp

yrettabegnahC

etomermargorP )9egap(lortnoc

mratonlliwmetsyS

rehtororooD neposiecnartne

nosithgilysetruoC

telaVnisimetsyS

edom

ecnartneesolC

ffothgilysetruocnruT

edomtelaVffonruT)6egap(

tratstonlliwmetsyS neposidooH

desserpsiekarB

doohesolC

ekarbesaeleR

Deleting Lost or Stolen Remote Controls fromYour System

If one of your remote controls is lost or stolen, follow these instructions

IMMEDIATELY to remove the control code from your system.

1. Have all remaining remote controls available.

2. Enter the remote control programming mode by following

steps 1 - 5of

Adding Remote Controls toYour System

(page 8).

3a. If you have only one remaining remote control, press the

ARM button on that remote control eight (8) times, pausing

at least 1 second between each press. Make sure that the

siren chirps each time you press the ARM button.

3b. If you have two remaining remote controls, press the ARM

button on each remote control four (4) times, pausing at

least 1 second in between each press. Make sure that the

siren chirps each time you press the ARM button.

3c. If you have three remaining remote controls, press the

ARM button on the two remote controls three (3) times, then

press the ARM button on the remaining remote control twice.

Pause at least 1 seconds in between each press. Make sure

that the siren chirps each time you press the ARM button.

4. Turn the vehicle ignition off to exit the programming mode.

When you are finished, the lost or stolen remote control will

no longer operate your system.

System Maintenance

(cont.)

Inhaltsverzeichnis

Andere Code Alarm Fernstartsystem Handbücher

Code Alarm

Code Alarm ca5554 Professional series Bedienungsanleitung

Code Alarm

Code Alarm CSI-100 Bedienungsanleitung

Code Alarm

Code Alarm SRT 6700 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 5050 Bedienungsanleitung

Code Alarm

Code Alarm ca5154 professional Series Bedienungsanleitung

Code Alarm

Code Alarm CA-550 Bedienungsanleitung

Code Alarm

Code Alarm CA 5051MT Bedienungsanleitung

Code Alarm

Code Alarm CA-500 Bedienungsanleitung

Code Alarm

Code Alarm CA 5150 Bedienungsanleitung

Code Alarm

Code Alarm CA-520A Bedienungsanleitung

Code Alarm

Code Alarm CA611 Bedienungsanleitung

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 5050 Bedienungsanleitung

Code Alarm

Code Alarm CA-430 Bedienungsanleitung

Code Alarm

Code Alarm PC 4400 Bedienungsanleitung

Code Alarm

Code Alarm Professional Series CA 4050 Bedienungsanleitung

Code Alarm

Code Alarm CA 4051 Bedienungsanleitung

Code Alarm

Code Alarm ca 4552 Bedienungsanleitung

Code Alarm

Code Alarm professional series PROCOMP Bedienungsanleitung

Code Alarm

Code Alarm PROFESSIONAL SERIES Bedienungsanleitung

Code Alarm

Code Alarm ca 4552 Bedienungsanleitung

Code Alarm

Code Alarm CA 5051 Bedienungsanleitung

Code Alarm

Code Alarm CA-520 Bedienungsanleitung

Code Alarm

Code Alarm CA 5055 Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung