Code Code Reader 1000 Bedienungsanleitung
C005905_04_CR1000_User_Manual
C005905_04_CR1000_UserManual
User Manual
Code Reader™ 1000
Manual Version 04
Release Date: January 2013
C005905_04_CR1000_User_Manual
Statement of Agency Compliance
Code voids product warranty if the hard case has been opened or tampered with in any way.
In addion, a CB Test Cercate has been issued by the Naonal Cercaon Board (NCB) indicang CR1000
meets all safety and quality standards in accordance to IEC 60950-1:2001, First Edion.
The Code Reader™ 1000 (CR1000) has been tested for compliance with FCC regulaons and was found to be
compliant with all applicable FCC Rules and Regulaons.
IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this device must not be
co-located or operate in conjuncon with any other antenna or transmier.
CAUTION: Changes or modicaons not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
The Code Reader 1000 has been tested for compliance to CE standards and guidelines and was found to conform
to applicable CE standards, specically the EMC requirements EN 55024, ESD EN 61000-4-2, Radiated RF Immunity
EN 61000-4-3, ENV 50204, EFT EN 61000-4-4, Conducted RF Immunity EN 61000-4-6, EN 55022, Class B Radiated
Emissions, and Class B Conducted Emissions.
C005905_04_CR1000_User_Manual
Code Reader™ 1000 User Manual
Copyright © 2013 Code Corporaon.
All Rights Reserved.
The soware described in this manual may only be used in accordance with the terms of its license agreement.
No part of this publicaon may be reproduced in any form or by any means without wrien permission from Code Corporaon. This
includes electronic or mechanical means such as photocopying or recording in informaon storage and retrieval systems.
NO WARRANTY. This technical documentaon is provided AS-IS. Further, the documentaon does not represent a commitment
on the part of Code Corporaon. Code Corporaon does not warrant that it is accurate, complete or error free. Any use of the
technical documentaon is at the risk of the user. Code Corporaon reserves the right to make changes in specicaons and
other informaon contained in this document without prior noce, and the reader should in all cases consult Code Corporaon
to determine whether any such changes have been made. Code Corporaon shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequenal damages resulng from the furnishing, performance, or use of this
material. Code Corporaon does not assume any product liability arising out of or in connecon with the applicaon or use of any
product or applicaon described herein.
NO LICENSE. No license is granted, either by implicaon, estoppel, or otherwise under any intellectual property rights of Code
Corporaon. Any use of hardware, soware and/or technology of Code Corporaon is governed by its own agreement.
The following are trademarks or registered trademarks of Code Corporaon:
CodeXML®, Maker, QuickMaker, CodeXML® Maker, CodeXML® Maker Pro, CodeXML® Router, CodeXML® Client SDK, CodeXML®
Filter, HyperPage, CodeTrack, GoCard, GoWeb, ShortCode, GoCode®, Code Router, QuickConnect Codes, Rule Runner®, Cortex®,
CortexRM, CortexMobile, Code, Code Reader, CortexAG, CortexStudio, CortexTools, Anity®, and CortexDecoder.
All other product names menoned in this manual may be trademarks of their respecve companies and are hereby acknowledged.
The soware and/or products of Code Corporaon include invenons that are patented or that are the subject of patents pending.
U.S. Patents: 6997387, 6957769, 7428981, 6619547, 6736320, 7392933, 7014113, 7240831, 7353999, 7519239, 7204417, 6942152,
7070091, 7097099, 7621453, 8001550, 8011584
The Code Reader soware uses the Mozilla SpiderMonkey JavaScript engine, which is distributed under the terms of the Mozilla
Public License Version 1.1.
The Code Reader soware is based in part on the work of the Independent JPEG Group.
Code Corporaon, 14870 South Pony Express Road, Suite 200, Bludale, UT 84065
www.codecorp.com
C005905_04_CR1000_User_Manual
Table of Contents
1.0 - Unpacking............................................................................................................................................................... 1
2.0 - Aaching/Detaching a Cable................................................................................................................................... 1
3.0 - Powering the Reader On/O................................................................................................................................... 1
4.0 - Using a CR1000 Out of a Stand................................................................................................................................ 2
5.0 - Using a CR1000 in a Stand....................................................................................................................................... 2
6.0 - Reading Range ........................................................................................................................................................ 3
7.0 - Reader Feedback .................................................................................................................................................... 3
8.0 - Symbologies Defaulted On...................................................................................................................................... 4
9.0 - Symbologies Defaulted O...................................................................................................................................... 4
10.0 - Locang the Hardware Revision Number .............................................................................................................. 4
11.0 - Reader ID & Firmware Version .............................................................................................................................. 5
12.0 - Hole Mounng Paern.......................................................................................................................................... 6
13.0 - CR1000 Overall Dimensions .................................................................................................................................. 6
14.0 - USB Cable Example with Pinouts........................................................................................................................... 7
15.0 - RS232 Cable Example with Pinouts ....................................................................................................................... 7
16.0 - Reader Pinouts ..................................................................................................................................................... 8
17.0 - Maintenance.........................................................................................................................................................8
18.0 - Warranty .............................................................................................................................................................. 9
C005905_04_CR1000_User_Manual
3.0 - Aaching Cable and Powering On/O the Reader
1.0 - Unpacking
Remove the CR1000 from its packing and inspect it for damage. If the reader was damaged during shipping, please call Code at
(801) 495-2200.
Depending on the kit ordered, a USB or RS232 Anity® cable has been included with your reader.
USB Anity® Cable RS232 Anity® Cable
w/ Power Supply
For USB Cable: plug the USB end of the Anity® cable into a USB port on the host device. Aer several seconds, the reader will beep
twice, the LED will turn o and the CR1000 is ready for use.
For RS232 Cable: plug the power supply into the AC outlet, plug the power supply cord into the barrel jack of the cable, and connect
the RS232 connector to the appropriate serial port on the host device. Aer several seconds, the reader will beep twice, the LED will
turn o and the CR1000 is ready for use.
To aach a cable, plug the RJ-50 end of the Anity® cable into boom of the reader (Figure 1). Firmly push the connector into the
reader, unl a snap can be heard to indicate the cable is properly aached. To detach a cable, press a paper clip into the hole on the
back of the CR1000 (Figure 2), and gently pull the cable from the reader.
2.0 - Aaching and Detaching a Cable
1
Figure 1 Figure 2
C005905_04_CR1000_User_Manual
4.0 - Using a CR1000 Out of a Universal Stand
5.0 - Using a CR1000 in a Universal Stand
Revision 3 Hardware of the CR1000 has a stand detecon feature. By default, when the
CR1000 is placed in the stand, the reader will enter into moon detecon mode. When
in this mode, simply place a bar code in the scan eld to acvate the reader. The CR1000
will beep and ash a green LED to indicate a ‘good read’ has occurred.
When the CR1000 is removed from the stand, the reader switches to manual mode and
the buon must be pressed to read a bar code (refer to Secon 4.0).
Revisions 1 and 2 Hardware of the CR1000 do not have a stand detecon feature
to enable moon detecon reading when the CR1000 is in a stand. To congure
these hardware revisions for moon detecon scanning, please refer to the CR1000
Conguraon Guide, located at www.codecorp.com/les.php and scan the appropriate
code.
2
See Secon 10.0 to learn how to determine your CR1000
hardware revision number.
Press and hold the buon on the top of the CR1000, the two blue bars eming from the
reader are used for targeng. Center the blue bars in the middle of a bar code. The opmal
reading distance from reader to bar code is approximately 4.0” (10 cm).
Once the reader is at the opmal distance, the reader will read the bar code. The CR1000 will
beep and ash a green LED to indicate a ‘good read’ has occurred.
To modify any default sengs, download the CR1000 Conguraon Guide at
www.codecorp.com/les.php and scan the appropriate code.
C005905_04_CR1000_User_Manual
6.0 - Reading Ranges
Note: working ranges are a combinaon of both the wide and high density elds. All samples were high quality codes
and were read along a physical center line at a 10° angle. Default AGC sengs were used. Accuracy= +/- 10%.
3
7.0 - Reader Feedback
Scenario Top LED Light Sound
CR1000 Successfully
Powers Up Green LED Flashes 1 Beep
CR1000 Successfully
Enumerates with Host
(via cable)
Once Enumerated,
the Green LED turns O 1 Beep
Aempng to Decode Green LED Light is O None
Successful Decode and
Data Transfer via Cable Green LED Flashes 1 Beep
Conguraon Code Successfully
Decoded and Processed Green LED Flashes 2 Beep
Conguraon Code successfully
decoded but wasn’t
successfully processed
Green LED Flashes 4 Beeps
CR1000 Performance
Test Code Min Inches (mm) Max Inches (mm)
3 mil Code 39 3.1” (80 mm) 4.0” (102 mm)
7.5 mil Code 39 1.3” (33 mm) 7.2” (182 mm)
10.5 mil GS1 DataBar 0.8” (20 mm) 8.7” (220 mm)
13 mil UPC 1.1”(28 mm) 11.0” (280 mm)
4.2 mil Data Matrix 1.9” (48 mm) 4.3” (110 mm)
5 mil Data Matrix 1.7” (43 mm) 4.5” (115 mm)
6.3 mil Data Matrix 1.3” (33 mm) 5.9” (150 mm)
10 mil Data Matrix 0.8” (20 mm) 7.1” (180 mm)
20.8 mil Data Matrix 1.1” (28 mm) 13.5” (343 mm)
C005905_04_CR1000_User_Manual
8.0 - Symbologies Defaulted On
Aztec
Codabar
Code 39
Code 93
Code 128
Data Matrix
Data Matrix Rectangle
9.0 - Symbologies Defaulted O
Aztec Inverse
Code 11
Code 32
Code 39 Extended Full ASCII
Code 39 Checksum
Composite
Data Matrix Inverse
Han Xin
The following are symbologies that have a default of ON. To turn symbologies on or o, scan the symbology bar codes located in
the CR1000 Conguraon Guide located at website at hp://www.codecorp.com.
The following are symbologies that have a default of OFF. To turn symbologies on or o, scan the symbology bar codes located in the
CR1000 Conguraon Guide located at website at hp://www.codecorp.com.
4
All GS1 DataBar
Interleaved 2 of 5
PDF417
QR Code
UPC/EAN/JAN
Matrix 2 of 5
Micro PDF417
Micro QR
MSI Plessey
Plessey
QR Code Inverse
Straight 2 of 5
Triopc
UPC-E Expansion
UPC Supplemental
10.0 - Locang the Hardware Revision Number
Locate the serial label on the boom of the reader to idenfy the hardware revision number of the CR1000.
Serial #: 20000XXXX
MFG #: CR1011_03
Designed in USA.
Made in Malaysia.
The number aer the underscore
( _ ) represents the hardware
revision number.
C005905_04_CR1000_User_Manual
11.0 - Reader ID and Firmware Version
Reader ID and Firmware
iVVVVWWWWXXXXSSSSSSSSSSAOODYYYYHHIIIIJJJJKKKKLLLL<TAB>Z…Z
5
To nd out the Reader ID and rmware version, open a text editor program (i.e., Notepad, Microso Word, etc.) and read the
following code:
You will see a text string indicang your rmware version and CR1000 ID number (see below):
i indicates ‘I’ string output;
VVVV is the applicaon rmware version number;
WWWW is the core applicaon rmware version number;
XXXX is reserved for the radio rmware version number;
SSSSSSSSSS is the Reader’s serial number (ten digits);
A is the current execuon state:
OO is the OEM idener;
D is the display type:
YYYY is the ash le system version number. Reserved;
HH is the hardware revision;
IIII is the hardware type idener: 0007 indicates a CR1000
JJJJ is the boot applicaon version;
KKKK is the operang system kernel version;
LLLL is the root le-system version;
<TAB> is the ASCII TAB character;
Z…Z is the OEM decoder version: a null terminated string of printable ASCII characters. Without a decoder.ini le,
the order of the decoders listed here indicates the order of use.
Example:
Xap/i3000300006040010002363A06D-SD+SQ
Note: Code will periodically release new rmware for CR1000 readers. For informaon on latest rmware versions,
call Code at (801) 495-2200. To upgrade rmware, please visit our website at hp://www.codecorp.com/
codesupport.php and follow instrucons provided.
“0” or “N” is no display device
“D” is the standard Keypad/Display
“A” means core is running
“B” means undened
“C” means undened
C005905_04_CR1000_User_Manual
12.0 - CR1000 Hole Mounng Paern
13.0 - CR1000 Overall Dimensions
NOTE 1:
LOCATING HOLES ARE 2MM IN DIAMETER, HOLE DEPTH is 1.5 MM
NOTE 2:
MOUNTING INSERTS ARE M3-.5 INTERNAL THREAD, 3.8MM LENGTH
6
Andere Handbücher für Code Reader 1000
3
Inhaltsverzeichnis
Andere Code Barcode-Lesegerät Handbücher
Code
Code Code Reader CR3500 Bedienungsanleitung
Code
Code CR5200 Bedienungsanleitung
Code
Code CR900FD Bedienungsanleitung
Code
Code CR1500-K10 Series Bedienungsanleitung
Code
Code Code Reader CR3500 Bedienungsanleitung
Code
Code CR1100 Bedienungsanleitung
Code
Code CR950 Bedienungsanleitung
Code
Code Code Reader 1000 Bedienungsanleitung
Code
Code CORTEXJPOS CR2300 Bedienungsanleitung
Code
Code CR2700 Bedienungsanleitung
Code
Code CR1000 Bedienungsanleitung
Code
Code CORTEXJPOS CR5000 Bedienungsanleitung
Code
Code Code Reader 822 Series Kurzanleitung zur Einrichtung
Code
Code 2600 Kurzanleitung zur Einrichtung
Code
Code Code Reader 2.0 Bedienungsanleitung
Code
Code CORTEXJPOS CR6000 Bedienungsanleitung
Code
Code CORTEXJPOS CR5000 Bedienungsanleitung
Code
Code CORTEXJPOS CR2300 Bedienungsanleitung
Code
Code CORTEXJPOS CR2600 Bedienungsanleitung
Code
Code 2600 Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
