Cole Parmer IP-400 Series Bedienungsanleitung

Cole-Parmer®IP-400 Low-Temperature

Immersion Chillers with Flexible Cold

Finger Probe

USER OPERATION MANUAL

Table of Contents

Introduction........................................................................................................................................................... 2

General Information .............................................................................................................................................. 2

General Safety Information ......................................................................................................................... 2

Safety Recommendations............................................................................................................................ 3

Unpacking Your Immersion Probe Cooler ..................................................................................................... 3

Regulatory Compliance & Testing ................................................................................................................ 4

Contents .................................................................................................................................................... 4

Controls & Components......................................................................................................................................... 5

Quick-Start ............................................................................................................................................................ 6

Installation & Startup ............................................................................................................................................ 7

General Site Requirements.......................................................................................................................... 7

Positioning the Immersion Probe Assembly .................................................................................................. 7

Electrical Power.......................................................................................................................................... 8

Normal Operation.................................................................................................................................................. 8

Turning Your Immersion Probe Cooler ON .................................................................................................... 8

Main Operational Display............................................................................................................................ 9

Display Messages ....................................................................................................................................... 9

Loss of Power Restart ................................................................................................................................. 9

Routine Maintenance & Troubleshooting ............................................................................................................ 10

Cleaning Exterior Surfaces ......................................................................................................................... 10

Cleaning the Air Filter ............................................................................................................................... 10

Draining Residual Oil from the Immersion Probe Assembly .......................................................................... 10

Troubleshooting ....................................................................................................................................... 11

Technical Information.......................................................................................................................................... 12

Performance Specifications ....................................................................................................................... 12

Equipment Disposal (WEEE Directive).................................................................................................................. 13

Service & Technical Support ................................................................................................................................ 13

Warranty ............................................................................................................................................................. 14

Introduction

Your Immersion Probe Cooler can be used to achieve low-temperature capability with non-refrigerated circulating

baths or boost the cooling capacity of refrigerated circulators. It is also excellent for trapping and Dewar-type

applications, making it an economical alternative to dry ice or liquid nitrogen. A 6-ft. (1.83 m) flexible hose allows

convenient placement of the cooling probe.

It will take you very little time to get your Immersion Probe Cooler installed and running. This operator’s manual is

designed to guide you quickly through the process. We recommend that you read it thoroughly before you begin.

NOTE: The Immersion Probe Cooler operates at maximum cooling performance. Maximum temperature

stability will be achieved in an agitated fluid and with a constant heat load. Allow ample time to reach the

lowest achievable temperature.

General Information

General Safety Information

When installed, operated, and maintained according to the directions in this manual and common safety

procedures, your Immerson Probe Cooler should provide safe and reliable cooling. Please ensure that all

individuals involved in the installation, operation, or maintenance of this unit read this manual thoroughly prior to

working with the unit.

This symbol marks chapters and sections of this instruction manual that are particularly relevant to safety.

When attached to the unit, this symbol draws attention to the relevant section of the instruction manual.

This symbol advises you of danger from electricity or electric shock.

This symbol marks information that is particularly important.

This symbol indicates alternating current.

These symbols on the Power Switch / Circuit Breaker indicate that they place the main power supply ON /

OFF.

This symbol on the Power Key indicates that it places the unit in a standby mode. It DOES NOT fully

disconnect the unit from the power supply.

This symbol indicates a protective conductor terminal.

Read all instructions pertaining to safety, set-up, and operation.

Proper operation and maintenance is the user’s responsibility.

Safety Recommendations

To prevent injury to personnel and/or damage to property, always follow your workplace’s safety procedures

when operating this equipment. You should also comply with the following safety recommendations:

WARNING:

• Always connect the power cord on this unit to a grounded (3-prong) power outlet. Make certain that the

outlet is the same voltage and frequency as your unit.

• Never operate the unit with a damaged power cord.

• Always turn the unit OFF and disconnect Mains power before performing any maintenance or service.

WARNING:

• Never touch the immersion probe assembly while the unit is operating.

• Always allow the immersion probe to warm to ambient temperature before repositioning or working on the

unit.

• Do not move the immersion probe assembly while the unit is operating.

Unpacking Your Immersion Probe Cooler

Your Immersion Probe Cooler was packed in a special carton. You should keep the packaging, along with all packing

materials, until the unit has been installed and you are certain it is working properly.

CAUTION:Remove any loose packing material that may have clung to the base or wand assembly.

WARNING:Keep unit upright when moving. Be sure to follow your company’s procedures and practices

regarding the safe lifting and relocation of heavy objects.

In the unlikely event that the unit was damaged or does not operate properly, contact the company where your

Immersion Probe Cooler was purchased.

Regulatory Compliance & Testing

cCSAus (120V, 60Hz units)

UL 61010-1 (3rd Edition) - Safety Requirements for Electrical Equipment for Measurement, Control, and

Laboratory Use - Part 1: General Requirements

CAN/CSA-C22.2 No 61010-1-12 - Safety Requirements for Electrical Equipment for Measurement, Control, and

Laboratory Use - Part 1: General Requirements

Product meets CAN ICES-1/NMB-1 and FCC Part 15

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This

device may not cause harmful interference, and 2. This device must accept any interference received, including

interference that may cause undesired operation.

IEC/CE (230V, 50Hz units; 100V, 50/60Hz units)

Machinery Directive 2006/42/EC Annex I

IEC 61010-1:2010 - Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory

Use - Part 1: General Requirements

EN 61010-1:2010 - Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use

- Part 1: General Requirements

EMC Directive 2014/30/EU

EN 61326-1:2013 - Electrical Equipment for Measurement, Control and Laboratory Use - EMC Requirements -

Part 1: General Requirements

RoHS Directive 2011/65/EU

EN 50581:2012 - Technical Documentation for The Assessment of Electrical and Electronic Products With

Respect to The Restriction of Hazardous Substances

Highly Accelerated Life Test (HALT) and Vibration Tests per ASTM D4169-8 (All units)

Contents

The Following Items Have Been Included With Your Immersion Probe Cooler:

• Operator’s Manual

• IEC Electrical Cord

• Certificate of Compliance

Controls & Components

IMPORTANT: The temperature display is for reference only. The actual temperature of the immersion

probe will be colder than the displayed temperature.

Cold Finger Immersion Probe Flexible Immersion Probe 1.75” Rigid Coil Probe

Power Key

Temperature Display

Air Filter

Compartment

Power Switch /

Circuit Breaker

IEC Electrical Connection

Rigid Coil Immersion Probe

(3” rigid coil shown)

Identification Label

Immersion Probe

Assembly

Quick-Start

1 Position Immersion Probe

2 Connect power. See

Identification Label.

3 Turn main power ON.

Turn Standby power ON.

Allow approximately 10

minutes for the system to

begin the cooling process.

Allow approximately 1 hour

for system to reach

-80°C (IP-80) or

-90°C (IP-100).

(typical)

CAUTION: Moving Immersion Probe Cooler while unit is operating may result in damage.

Installation & Startup

Your Immersion Probe Cooler is designed to be simple to set-up and install. No tools are required.

General Site Requirements

Locate the unit on a level surface, free from drafts and out of direct sunlight. Do not place it where there are

corrosive fumes, excessive moisture, high room temperatures, or where excessive dust is present.

The unit must be a minimum of 6 inches / 15.24 cm away from walls or vertical surfaces so that airflow

around the unit is not restricted. It should not be placed in cabinets or where exiting warm air or warm air

from other devices will be drawn into the air intake on the front of the unit.

NOTE: It is recommended that your unit be run in ambient temperatures below 95°F / 35°C. While the

unit will operate at higher ambient temperatures, it may not be able to achieve maximum cooling

performance.

Positioning the Immersion Probe Assembly

When installing the unit, make sure that the Immersion Probe Assembly is properly positioned. It should not

be twisted. Incorrect positioning of the Wand Assembly will cause your Immersion Probe Cooler to perform

below specifications.

CAUTION: Moving the Immersion Probe Assembly while the unit is operating may result in damage.

Electrical Power

WARNING: IMPORTANT INFORMATION FOR 100V APPLICATIONS

On 100V 50Hz applications a step-up transformer IS NOT NEEDED and MUST NOT be used.

On 100V 60Hz applications a step-up transformer MUST be used.

WARNING: Make certain that the electrical outlet is the same voltage and frequency as your unit. The correct

voltage and frequency for your unit are indicated on the Identification Label on the back panel.

WARNING:The use of an extension cord is not recommended. If one is necessary, it must be properly

grounded and capable of handling the total wattage of the unit. The extension cord must not cause more than

a 10% drop in voltage to the unit.

Attach the 6-ft / 1.8 m power cord to the IEC electrical connector on the back of the unit and then plug the male

connector into the Mains electrical outlet.

Place the Power Switch / Circuit Breaker on the back of the Immersion Probe

Cooler in the ON position. Three decimal points will appear on the

Temperature Display. This indicates that the unit is in Standby mode.

Your Immersion Probe Cooler is now ready to begin normal operation.

Normal Operation

Turning Your Immersion Probe Cooler ON

Press the Power Key on the front panel. After a brief initialization message,

the probe temperature will appear on the Temperature Display. After five

minutes, the first stage compressor and fan will turn on to begin the cooling

process. During this start-up phase, the displayed temperature will remain

near or at ambient temperature.

After approximately 10 minutes, the second stage compressor will turn on,

refrigerant will begin circulating through the system, and the displayed

temperature will begin decreasing. It generally takes approximately 60 minutes from power up for the IP-80 to

reach -80°C or for the IP-100 to reach -90°C.

NOTE: The Immersion Probe Cooler operates at maximum cooling performance.

IMPORTANT: To protect its compressors from damage, the Immersion Probe Cooler incorporates a

special safety switch that delays compressor startup for 10 minutes whenever power is applied. This 10

minute delay will occur even when power is only momentarily disrupted.

Main Operational Display

The actual temperature of the immersion probe is displayed in degrees C on

the unit’s digital readout. Due to the location of the temperature sensor, this

temperature is a few degrees warmer than the surface temperature of the

immersion probe.

Display Messages

Temperature Display Description

Standby Mode — Indicates that the Power Switch / Circuit Breaker on the back

panel is in the ON position and unit is ready to operate.

Power On / Start-Up — Appears briefly when the Immersion Probe Cooler is

turned ON by pressing the Power Key on the front panel. The information

represents the firmware version.

Main Operational Display — Indicates unit is ON and operating. Displayed

temperature is in degrees C.

Note: Displayed temperature is to one tenth of a degree (X..X) until it reaches -

10°.

Warning Display — Indicates that the external temperature sensor is not

functioning properly. Unit will continue to cool.

Loss of Power Restart

In the event that electrical power is disrupted during operation, the unit will begin operating automatically when

power is restored. As with normal start-up, it will take approximately 60 minutes for the IP-80 to reach -80°C or the

IP-100 to reach -90°C.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cole Parmer Kühler Handbücher

Cole Parmer

Cole Parmer Polystat I Betriebsanleitung

Beliebte Kühler Handbücher anderer Marken

Aqua Optima

Aqua Optima Corona Bedienungsanleitung

York

York YGWH 115 Leitfaden

Galletti

Galletti PERFORMA MPE Series Bedienungsanleitung

SMC Networks

SMC Networks HRR Series Bedienungsanleitung

Daikin

Daikin EWAQ016CAW Bedienungsanleitung

Trane

Trane CVHE Betriebsanleitung

Moffat

Moffat Friginox TSR-11SC Bedienungsanleitung

Gree

Gree GWH07AGA-K6DNA1C Bedienungsanleitung

Denali

Denali M1 Bedienungsanleitung

MP Systems

MP Systems PURGE Series Bedienungsanleitung

AEC

AEC PCA SERIES Technisches Datenblatt

Carrier

Carrier AquaEdge 19XRV series Betriebsanleitung

Telemark

Telemark TVP-2000 Handbuch

TICA

TICA MINI VRF CHR Series Bedienungsanleitung

Penguin

Penguin COLD THERAPY CHILLER Bedienungsanleitung

MAXA

MAXA A68 Bedienungsanleitung

SABROE

SABROE ChillPAC Bedienungsanleitung

Daikin

Daikin EWWQ-AJYNN Bedienungsanleitung