11412133 (Pg. 2)
Two Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(16)
Three Main Control Knobs . . . . . . . . . . . . . . . . . . . . . .(32)
One Grease Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(48)
One Grease Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(49)
Three Heat Tents . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(61)
One Meat Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(57)
One Meat Probe Receptacle . . . . . . . . . . . . . . . . . . . . .(57a)
One Handle Assembly
One Literature Bag
One 6-lobe Screwdriver
Hardware bag(s)
Assorted assembly hardware - One Igniter Kit bag
Two Axle pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .(3)
CARTON A - MISCELLANEOUS PARTS
BEFORE
YOU
BEGIN
ASSEMBLING
YOUR
NEW
QUALITY
COLEMAN
GAS
BARBECUE
GRILL:
ÖFOR EASE OF ASSEMBLY, leave the grill on
the inside bottom foam packing tray until the
wheels have been attached. (See representative
example at right). Remove the outside foam from
the right and left sides of the frame base at this
time.
ÖRemoveallcartonslocatedontopofthebarbecue
grill base and set aside.
Engineering Co e
LG114333
Tools Needed
Ö#20 6-Lobe Screwdriver (Included)
Ö#2 Phillips Screwdriver
ÖAn adjustable wrench
Ö9-Volt Battery (Included)
Optional Tools
Ö7/16" and 5/16" Box End Wrenches
Ö7/16" Nut Driver
ÖElectric or Cordless Screwdriver
Ö#20 6-Lobe driver bit
Ö#2 Phillips driver bit
START THE COOKING GRIDS
SEASONING PROCESS BEFORE
ASSEMBLING YOUR GRILL!
CAST
IRON
GRIDS
ÖCast Iron grids are on select models only.
ÖYour cast iron grids may have some rusting.
This is normal. To remove the rust, scour the
rusty areas with steelwool, i.e. SOS pad, until
all traces of rust are gone. Wash, dry and
season grids.
SEASONING
CAST
IRON
GRIDS AND
GRIDDLE
SEASONING IS THE PROCESS OF ALLOWING OIL TO BE
ABSORBED INTO THE IRON, CREATING A NON-STICK,
RUSTPROOF FINISH. HERE’S HOW TO DO IT:
ÖPreheat Oven to 350ºF.
ÖWash with hot, soapy water and a stiff brush.
Rinse and dry completely.
ÖOil the grids (all surface top and bottom) with
MELTED solid vegetable shortening.
ÖTurn upside down on the top rack of a 350ºF
pre-heated oven.
ÖPut aluminum foil on the bottom rack to catch
any excess drippings.
ÖBake the grids for one hour at 350ºF.
ÖLet the grid cool slowly in the oven.
ÖStore, uncovered, in a dry place when cooled.
ONE CARTON - L.P.GAS CYLINDER
WARNING:
Combustion by-products produced when using
this product contain chemicals known to the State
of California to cause cancer, birth defects, or
other reproductive harm.
CARTON B - 2 SIDE TABLE
ASSEMBLIES
(FOR MODELS WITHOUT SIDE BURNER)
One pre-assembled right sidetable
One pre-assembled left sidetable
