Combi Smart Hold OKF11 Montageanleitung

Combi Vertical Diaper Changing Station “Smart Hold OKF11”

[To the person in charge of installation]

The inspection after the installation is the same as the daily

inspection. After installation is complete, inspect the product by

referring to 2 Daily Inspection on pages 3 to 4.

Save This Manual for Future Reference

Combi Vertical Diaper Changing Station

“Smart Hold OKF11”

Daily Inspection and

Periodical Inspection Manual

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual

1Part Name

Introduction

Table of Contents

1 Part Name ....................................... page 2

2 Daily Inspection ............................... page 3

3 Periodic Inspection .......................... page 5

4 Part Replacement ............................ page 8

5 Others ........................................... page 10

This manual describes the details of "Daily Inspections" and "Periodic Inspections" required for the

comfortable and safe use of Combi Vertical Diaper Changing Station " Smart Hold OKF11". Be sure to perform

daily or weekly inspection and annual periodic inspections in accordance with the contents of this manual.

Main Body Sticker

Bottom Cover

(Panel Base)

Hinge Cover

(Right)

Hinge Cover (Left)

Top Cover (Panel Top)

Instruction Sticker

Belt

Buckle

Baggage Hook Sticker

Head Cushion Seat Cushion

Table Panel (Head Lower)

Serial Sticker

(Sticker at far right)

Inspection Sticker

Baggage Mark Sticker

Side Guard

Table Panel

(Head Upper)

Baggage Hook

(left and right)

Product Life

The product life is 7 years in normal use. The product must be replaced at the end of the product life.

The storage period for repair parts is 5 years after the nal production.

①

No scratches, cracks or rattling on the buckle.

②

No fray or damage on the belt.

③Insert the buckle until it clicks, and pull the

belt to make sure the bukkle is not relrased.

Daily inspections are carried out daily or weekly basis by visual and touch. No tools are used.

①The parts should not be missing or the

seat cushion or head cushion are not

loose.

② Close the main body and conrm that the

table panel does not rattle by shaking.

①

Open the main body and conrm that the

table panel does not rattle by swinging it

from side to side.

②Opening and closing of the table panel

should be smooth.

③No scratches or cracks.

Checking

Buckle

Confirmation

of releasing

the buckle

⑤The belt shall be free from twisting and it

can be stored smoothly.

If any malfunctions are found during the inspection, immediately discontinue the usage and contact

sales agent to request service.

❷Released

❶Press

Buckle Holder

* Replace the belt (with retractor) if the belt is

broken, frayed, or severely soiled. Refer to 4 Parts

Replacement, "Belt Replacement Procedure" on

page 8.

Buckle

2Daily Inspection

Checking belts and buckles

Checking external appearance

Checking the open/close operation of the table panel

④The buckle can be fastened an released

reliably.

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual

The sticker should be properly affixed and contents are readable. (No scratches, tears, missing,

or discoloration)

The contents should be readable. (dirt mark, graffiti, etc.)

* The sticker contains warnings and cautions for safety use.

Guide Sticker

Attached to the entrance of the toilet,

or to the door of the toilet booth, etc.

Warning Sticker

Attach to a position near the

product and easy to see

Main Body Sticker

Front of the table panel

Instruction Sticker

Front of the top cover

when the table is open.

Baggage Mark Sticker

(2 pcs)

Both sides of the table panel

Warning Sticker

Main Body Sticker

Instruction Sticker

Baggage Hook Stickers (2 pcs)

Serial Sticker

Upper right of the upper cover

(Lot No in lower column)

Baggage Hook Stickers

(2 pcs)

Both sides of the side guard

Inspection Sticker

Upper cover, lower right

Baggage Mark Sticker (2 pcs)

Serial Sticker

Inspection Sticker

Toilet Entrance Toilet Booth

Place of Application

Checking stickers

● Periodic inspections are conducted periodically about

once a year.

● In the periodic inspection, check the daily inspection

points and remove each part according to the following

and check the condition of each part.

If any issues are found during inspection,

immediately discontinue the usage and contact

sales agent to request service.

The screws (3 locations) on the back of the

buckle should not be missing or loose.

Remove the head cushion and check the

upper cover xing screws and washers (2

locations) are not missing or loose, and

then remove the screws.

After checking the lower cover xing screws

[2 locations ] are not loose, and then

remove the screws.

Philips screwdriver, wrenches, etc. Caution

Be sure to tighten the screws by hand.

The plastic part may be damaged if power tools

are used.

Check the screws used for each part for damage of the

cross-recess, deformation of the screws, and rust. If any

abnormality is found, replace the screws with new ones.

Remove the top cover from the frame.

Buckle

Head Cushion

Top Cover

3Periodic Inspection

Required Tool

①Check the screws on the buckle ② Check the upper cover xing screws

③ Check the lower cover xing screws

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual

Check the 3 anchor bolts for fixing the leg

frame are not missing or loose.

Leg Frame

Anchor Bolt

Remove ❶the bottom cover and ❷hinge

covers from the frame in this order.

❶

❷

Lower Cover

Hinge Cover

It is xed to the large hole.

❸

❶❷

❹

Check that the anchor bolts (6

locations) are not missing or

loose.

Check no rust on the main body

frame

When the table panel is closed the

tools can be used for the lower 2

holes, ❺and ❻from the front.

④ Checking the xing anchor bolts for the leg frame

⑤ Check the rust on screws to x to the wall and the main body frame

For concrete and ALC

❻➡

Right Side

❺➡

Secure the lower cover

with the screws.

When the table panel is closed the tools

can be used for the lower 2 holes, ❻and

❼from the front.

It is xed in the small holes.

❸

❶❷

❹

Check the screws (7 locations) are not

missing or loose.

Check the main frame for rust. ❺

Put

❶

hinge cover,

❷

lower

cover on the frame in this

order.

❶

❷

Secure the

top cover to

the frame with

screws and

install the head

cushion.

❶

❷

❸

Hinge Cover Top Cover

Head Cushion

①Retractor operates smoothly and it locks.

②The buckle clicks on the buckle receiver and locks.

⑦Check the operation of the retractor and buckle.

⑤ Check for rust on wall xing screws and main body frame

⑥Assembly

For partitions, gypsum boards

❼➡

Right Side

❻➡

Insert at back

side of upper

cover (left and

right)

Lower Cover

Insert into the holes of the

frame by pushing 2 locations. Insert at lower

side of upper

cover (left and

right)

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual

Belt Replacement

If broken, frayed, or severely soiled belt is found during daily inspections. It is recommended to

purchase "Belt Retractor Replacement Set" and replace it in the following procedure.

Remove buckle

Remove the metal rod and drop the belt into the belt hole.

Remove the seat cushion and head cushion. Remove the xing screws and washers

(2 locations) and remove the top cover.

Remove the table panel (top).

Remove the table

panel xing screws

(13 locations).

Remove the baggage

mark stickers (2

locations).

Buckle Metal Rod

Top Cover

Caution

The sticker may damaged, use

enclosed new baggage mark

sticker (2 pcs).

* Included in replacement sets.

❶ ❷

❸ ❻

❼ ❽

󱢳󱢴󱢵

❹ ❺

❾ 󱢶

Table Panel

(Upper)

Belt

Seat Cushion

Head Cushion

* Replace the belt with a retractor.

* It can be removed without tools.

4Part Replacement

Remove the 4 fixing screws and replace the

belt including the retractor.

Extract the belt from the retractor and pass through

the belt hole in the table panel (upper side).

Secure the table panel (inside) with screws (13 locations).

Secure the buckles with the screws (2 locations).

Refer to 5for the position of the screw.

Affix new baggage

mark stickers (2

locations).

Belt

Table Panel

(Upper)

If a metal bar is

passed through the

belt, it will not fall

into the belt hole.

Metal Rod

Secure the top cover with the screws and washers (2 locations).

Attach the seat cushion and the head cushion. Check the belt and buckle.

Top Cover

①No scratches, cracks or rattling on the buckle.

②No fray or damage on the belt.

③Insert the buckle until it clicks, and make sure it is

fastened by pulling the belt.

④The buckle can be locked and unlocked reliably.

⑤The belt shall be free from twisting and shall be

stored smoothly.

(See page 3 for the inspection method.)

Seat Cushion

Head Cushion

Retractor

Press the two area of the connecting

tape by hand securely.

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual

Refer to Belt Replacement 1to 5for the disassemble of the table panel.

Turn the table panel over and remove the screws. Replace the buckle holder and x it with screws.

For the assembly of the table panel, see "Belt Replacement" on 7to 󱫒on page 9.

(Be sure to inspect the belt and buckle after replacement.)

5Others

After periodic inspection, enter

the inspection date on the

<Inspection Sticker> attached to

the upper cover (lower right).

Inspection sticker are available

for purchase.

Inspection

Sticker

Inspection Sticker

Recording inspection dates

To ensure safety use of the product, the warning

stickers are enclosed as an accessory to the

product. Additional sticker are available for purchase. Warning

Sticker

Warning Sticker

Procedure of replacing buckle holder

● This product is a dedicated for changing diaper for

children. Clean regularly to keep immaculate after

installation.

● When cleaning, use diluted neutral detergent to

wipe, then wipe it with wet cloth, then wipe with

dry cloth to take off moisture.

Cleaning

Caution

Do not use detergents other than neutral

detergents. Deterioration, fade, or crack may

occur on plastic and they cause damage.

Inhaltsverzeichnis

Andere Combi Baby- und Kleinkindmöbel Handbücher

Combi

Combi Activity Rocker Select Bedienungsanleitung

Combi

Combi Deluxe Activity Rocker 9725 Series Bedienungsanleitung

Combi

Combi Travel Solutions Play Yard Bedienungsanleitung

Combi

Combi F72 Montageanleitung

Combi

Combi Nemulila Winnie The Pooh Bedienungsanleitung

Combi

Combi Activity Rocker Pedestal 9790 Series Bedienungsanleitung

Combi

Combi Activity Rocker 9720 Bedienungsanleitung

Combi

Combi Pod Bouncer Bedienungsanleitung

Combi

Combi OK21F Montageanleitung

Beliebte Baby- und Kleinkindmöbel Handbücher anderer Marken

Mocka

Mocka Learning Tower Bedienungsanleitung

VERTBAUDET

VERTBAUDET 62003-2789 Bedienungsanleitung

Summer

Summer MY FUN POTTY Bedienungsanleitung

Grotime

Grotime Changeover Bedienungsanleitung

Fillikid

Fillikid 1221 Bedienungsanleitung

Relita

Relita loft bed ALEX Bedienungsanleitung

Joovy

Joovy Qool Bedienungsanleitung

KidKraft

KidKraft Step n Store Bedienungsanleitung

Fisher-Price

Fisher-Price L4889 Bedienungsanleitung

Germania

Germania Moon 4048.101 Bedienungsanleitung

BabyGo

BabyGo Amila Bedienungsanleitung

Fisher-Price

Fisher-Price CBV06 Bedienungsanleitung

Fisher-Price

Fisher-Price H4790 Bedienungsanleitung

Graco

Graco Dream Suite Bedienungsanleitung

Delta Childrens Products

Delta Childrens Products BB87116CR Bedienungsanleitung

Costway

Costway BB5591 Bedienungsanleitung

SAUTHON

SAUTHON UP CHENE DORE UI101A Bedienungsanleitung

Delta Children

Delta Children Classic Bedienungsanleitung