Comdial DSU II Series Bedienungsanleitung
Industry Standard Telephone (IST)
Station User’s Guide
DXP, DXP Plus, and FX Digital Telephone Systems
Comdial strives to design the features in our communications systems
to be fully interactive with one another. However, this is not always
possible, as the combinations of accessories and features are too
varied and extensive to insure total feature compatibility. Accord-
ingly, some features identified in this publication will not operate if
some other feature is activated.
Comdial disclaims all liability relating to feature non-compatibility or
associated in any way with problems which may be encountered by
incompatible features. Notwithstanding, anything contained in this
publication to the contrary, Comdial makes no representation herein
as to the compatibility of features.
Issued: 08/02
This user’s guide applies to industry standard
single-line telephones such as the model
2500-** when used with the DXIST-** or
FXIST*-** industry standard telephone inter-
face circuit board.
Contact your Comdial dealer for updates of
this as well as other Comdial publications as
your needs require.
September, 02 Comdial i
Industry Standard Telephone User’s Guide
1. INTRODUCTION...........................................................1
2. FLASHING THE HOOKSWITCH ..............................1
3. ANSWERING CALLS ...................................................2
3.1 Answering A Call......................................................2
3.2 Using Call Pickup......................................................2
3.3 Using Night Mode.....................................................2
4. MAKING CALLS...........................................................3
4.1 Using Prime Line Preference ....................................3
4.2 Using Prime Intercom ...............................................3
4.3 Using Last Number Redial........................................5
4.4 Using Speed Dialing..................................................6
5. HOLDING CALLS.........................................................9
5.1 Using Call Park .......................................................10
6. TRANSFERRING OUTSIDE CALLS .......................11
6.1 Using Screened Transfer .........................................11
6.2 Using Unscreened Transfer .....................................11
7. CONFERENCING STATIONS...................................13
7.1 Using Broker’s Call.................................................14
8. USING THE MESSAGING FEATURE.....................15
8.1 Using LCD Messaging ............................................16
9. USING RECALL/FLASH............................................17
Contents
ii Comdial September, 02
10. MAKING A PAGING ANNOUNCEMENT ..............18
10.1 Using External Paging...........................................18
10.2 Using All-Call and Zone Paging ...........................18
10.3 Using Meet-Me Page.............................................19
11. FORWARDING CALLS .............................................20
11.1 Call Forward Outside System (CFOS).................21
12. USING THE TRACKER PAGING SYSTEM ...........23
12.1 Responding To Tracker Pager Calls......................24
13. CAMPING ON AT A STATION.................................26
13.1 Camping On To An Idle Station............................26
13.2 Camping On To a Busy Station .............................27
13.3 Initiate Call Waiting At A Busy Station................28
13.4 Line Call Waiting ..................................................29
14. QUICK REFERENCE GUIDE ...................................31
15. GLOSSARY ..................................................................33
Industry Standard Telephone User’s Guide
September, 02 Comdial 1
1. INTRODUCTION
This manual serves as a helpful guide for using all the functions of
your new telephone and as a quick reference guide.
You may have your telephone programmed to provide an intercom
dial tone when you lift the handset. This arrangement is known as
“prime intercom.” You may, however, have your telephone pro-
grammed to provide outside line dial tone instead. This arrangement
is known as “prime line automatic” or “idle line preference.” Unless
otherwise noted, the following instructions are for telephones with
prime intercom, which means that you can dial system feature codes
as soon as you lift the handset. If your telephone has a different
arrangement, you must obtain intercom dial tone before you can dial
the various feature codes. To do this, press and release the hookswitch
after you hear the outside line dial tone. This action places the outside
line on hold and causes intercom dial tone to return to your telephone.
2. FLASHING THE HOOKSWITCH
Pressing and releasing the hookswitch is commonly known as
“flashing” the hookswitch or performing a FLASH. If your telephone
has a TAP button, we recommend that you press TAP instead of
flashing the hookswitch, since you can inadvertently disconnect the
line by pressing and releasing the hookswitch.
If your system has the internal flash feature enabled, you can obtain
intercom dial tone while on an outside line by flashing the hook-
switch. However, to generate a hookflash signal on the outside line,
you must flash for intercom and dial Ã08. With the internal flash
feature disabled, you can flash the hookswitch while on an outside
line to generate a flash on an outside line. However, you cannot flash
the hookswitch to obtain intercom dial tone.
Answering Calls
2 Comdial September, 02
3. ANSWERING CALLS
3.1 Answering A Call
• To answer a call that is ringing at your telephone,
–lift handset.
3.2 Using Call Pickup
• To answer a call that is ringing at another station in your
group
1. Lift handset.
2. Dial # 4. (you must have the ringing station programmed into
your call pickup group).
• To answer a call that is ringing at any station
1. Lift handset.
2. Dial * 4 plus station number of ringing telephone
3.3 Using Night Mode
• To answer a call that is ringing the night bell or night
transfer station (LAFAS-Line Answer From Any Station)
1. Lift handset.
2. Dial zone code 65–68 to select the ringing zone (1–4) at the
location of the bell, or dial zone code 69 to answer any ringing
zone.
3. Answer call.
Industry Standard Telephone User’s Guide
September, 02 Comdial 3
4. MAKING CALLS
4.1 Using Prime Line Preference
The following instructions apply to telephones programmed for prime
line automatic or idle line preference.
• To make a call
1. Lift handset and listen for outside dial tone.
2. Dial the outside number.
• To access an intercom line
1. Lift handset.
2. FLASH the hookswitch.
3. Listen for intercom dial tone.
4. Dial station number or intercom feature code.
5. Complete intercom call.
6. Hang up handset.
4.2 Using Prime Intercom
The following instructions apply to telephones programmed for prime
intercom.
• To make a call
1. Lift handset and listen for intercom dial tone.
2. Dial station number or intercom feature code, or use the redial
or speed dial feature.
Making Calls
4 Comdial September, 02
• To access outside line using line group feature
1. Lift handset and listen for intercom dial tone.
2. Dial the line group access code:
Line Group Access Codes
9 = line group 1,
80–89 = line groups 2 through 11,
60–64 = line groups 12 through 16,
3. Listen for outside dial tone.
4. Dial number or use the redial or speed dial feature.
• To queue for a busy line group
1. Lift handset and listen for intercom dial tone.
2. Dial line group access code (9, 80–89, 60–64).
3. Hear busy tone.
4. Dial * 6.
5. Hang up.
• To answer queuing ring-back
—Lift handset and hear dial tone for outside line.
• To cancel queuing
1. Lift handset and hear dial tone.
2. Dial # 6.
3. Hang up.
Industry Standard Telephone User’s Guide
September, 02 Comdial 5
4.3 Using Last Number Redial
• To redial the last number that you dialed at your telephone
1. Lift handset and listen for intercom dial tone.
2. FLASH the hookswitch and press #. The system makes the call
over the last line that you used.
• To redial the last number that you dialed at your telephone
(if the last line you have used is busy)
1. Dial line group access code (9, 80–89, 60–64).
2. FLASH the hookswitch,
3. Dial * 01 #.
Making Calls
6 Comdial September, 02
4.4 Using Speed Dialing
• To program personal speed dial numbers
1. Lift handset and listen for intercom dial tone.
2. Dial * * 1.
3. Dial memory location (1–0), then dial 00 for prime/last line -or-
01–16 for line groups 1–16.
4. Dial the number sequence you want to store (up to 16 digits
that can include # and *).
5. If necessary, press and release the hookswitch to store a hook-
flash.
6. Hang up the handset.
7. Repeat the above procedure for each speed dial number you
wish to program.
)
To prevent the possibility of storing an incomplete speed dial
number, hang up your handset and lift it again between each
number you are programming. The dual tone multi frequency
(DTMF) receiver times out in 20 seconds (default), or the
installer can set it for any value between 5 and 45 seconds.
Hanging up your handset between each programming entry
causes the DTMF receiver timer to restart before you begin
programming the next number.
Andere Handbücher für DSU II Series
3
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
Andere Comdial Telefon Handbücher
Comdial
Comdial GCA70-33 Bedienungsanleitung
Comdial
Comdial Executech 2232 Bedienungsanleitung
Comdial
Comdial Quick Q Bedienungsanleitung
Comdial
Comdial 7OlOS Bedienungsanleitung
Comdial
Comdial GCA70-248 Bedienungsanleitung
Comdial
Comdial Impact 8012S Series Bedienungsanleitung
Comdial
Comdial DSU Series Bedienungsanleitung
Comdial
Comdial Solo II 5531S Bedienungsanleitung
Comdial
Comdial GCA70-313 Bedienungsanleitung
Comdial
Comdial Hot Desking Bedienungsanleitung
Comdial
Comdial Impact Concierge 8312S Series Bedienungsanleitung
Comdial
Comdial FX Series Bedienungsanleitung
Comdial
Comdial X34PT Bedienungsanleitung
Comdial
Comdial DigiTech 7700S Series Bedienungsanleitung
Comdial
Comdial 1432B Bedienungsanleitung
Comdial
Comdial DXP Digital Communications System Bedienungsanleitung
Comdial
Comdial Quick Q Bedienungsanleitung
Comdial
Comdial 8412F Bedienungsanleitung
Comdial
Comdial Quick Q Bedienungsanleitung
Comdial
Comdial DSU and DSU II Bedienungsanleitung
