Comet SP015 Bedienungsanleitung

Specification are subject to change without notice ie-wfs-SP015-02

SP015

Batteries holder with connection adapter

DESCRIPTION AND APPLICATION

The SP015 Batteries holder is designed to be used as an accessory for battery powered transducers

with radio output to Sigfox net (from Wx8xx series*). It allows you to power the transducer from one or

two 3.6V lithium batteries, size "C", thus extending up to six times the operating time compared to the

standard life of size "AA" internal battery. It is equipped with a connection adapter that is mounted in

place of the transducer's internal battery. The SP015 Batteries holder is suitable for applications

where the life of the transducer's internal battery is insufficient and the mains power supply (with

optional accessories) cannot be used.

*) Applicable to W0810, W0811, W0832, W0850, W3810, W3811, W7810 models.

SAFETY NOTICE

use only recommended batteries in the device

never mix different manufacturers' batteries or new ones with those already in use

do not short circuit output of the device, the batteries will be destroyed

always insert batteries with the correct polarity, never with the reversed polarity

do not exceed the specified operating temperatures

device contains electronic parts that must be disposed of in accordance with local

and currently valid legal conditions

POWER SUPPLY BATTERIES

SP015 Batteries holder is supplied separately, without batteries. It is designed for primary lithium

batteries 3.6V, size "C". We recommend using Tadiran SL2770/S batteries (order code A4206). One

or two batteries can be fitted. If you choose to use two batteries, always use batteries the same type

and manufacturer, origin from same delivery, ie. same age. Always use new, unused batteries. It is

forbidden to combine batteries from different manufacturers or to mix new batteries with those already

in use.

Battery life values table for operating temperatures up to + 35 ° C:

sending interval:

10 min

20 min

30 min

1 h

3 h

6 h

12 h

24 h

1 pc battery

1 year

2 years

3 years

5 years

10 years

> 10

2 pc batteries

2 years

4 years

6 years

10 years

> 10

Use two batteries only in applications where the transducer will be set to shorter sending intervals

(from 10 min to 1 h). For long sending intervals (3 h or longer), you can achieve a life of 10 years or

more at normal operating temperatures, even with one battery. Battery life of more than 10 years is

rather theoretical, because at such a long time the effect of batteries self-discharge may be higher

than the power consumption of the device.

- 2 -

At continuous operating temperatures above 35 °C, the battery life may drop by a third or half. In

accordance with the transducer manual, the battery life values apply when extraordinary alarm

messages are not used or only exceptionally.

PUTTING DEVICE INTO OPERATION

1) Mounting the connection adapter on the transducer

unscrew the four screws at the corners of the

transducer case and remove the cover

if you have a new transducer, install it according to the

transducer manual (keep it working from the supplied

battery). After the adapter is mounted, the

Configuration button inside the device will not be

accessible - therefore, before continuing, make sure

that the device is turned on and that you do not

require accelerated transducer parameter settings.

remove the battery by pulling on its handle from the

ready transducer

insert one SP015 connection adapter contact into the

Wx8xx transducer battery contact field. Then insert

the second contact into the other the transducer

battery contact field and close the cover. The contacts

of the two devices must fit exactly together.

verify that the connection adapter is flush with the

transducer housing circuit. If not, remove the adapter

and repeat the assembly procedure. Under no

circumstances should you attempt to force the adapter

and transducer into the correct position.

if the adapter is in the correct position, screw it with

the original screws

keep the original cover and battery for case the

adapter is will removed

- 3 -

2) Battery installation

unscrew the four screws at the corners

of the Batteries holder case and

remove the cover

depending on the required life (see

table above), insert into the Batteries

holder one or two a 3.6V lithium

batteries (of the same type and

manufacturer) with polarity as shown

on figure. Push the battery against

the spring of negative contact and then

release it. Display of the transducer

must light up within 10 seconds and

the transducer will start working.

screw the batteries holder cover. Make sure that the contact surfaces of gasket are free of dirt.

3) Assembly and fixing of the assembly

screw the transducer onto the holder

posts (1) with the supplied M4 screws

screw all the assembly on the selected

measuring place (2). Observe the

installation instructions and location

rules in the transducer manual.

Depending on the type of material on

which the entire assembly will be

mounted, use two suitable 4 mm

diameter screws.

if, for space reasons, it is preferable to

arrange both devices side by side,

remove the metal posts and montage

plate from the batteries holder and

screw the holder to the left side of the

intended transducer position.

Depending on the type of material on

which the entire assembly will be

mounted, use four suitable 4 mm

diameter screws.

- 4 -

BATTERY REPLACEMENT

If it is necessary to replace the batteries in the

Batteries holder directly at the installation site, first

unscrew the transducer from the holder posts (2

M4 screws) and move it to the right of the Batteries

holder. Temporarily attach the transducer with only

one screw to the right post of the Batteries holder

as shown. Do not let the transducer hang by the

power cord. Remove the four screws at the corners

of case the Batteries holder and remove the cover.

Replace the batteries with new ones and

reassemble all the assembly in reverse.

TECHNICAL PARAMETERS

recommended batteries: Tadiran SL2770/S, lithium, 3.6 V, size "C"

output voltage: 3.6 V DC

continuous output current: max. 200 mA

short circuit protection of output: no (recommended batteries are not dangerous in the event of a short circuit)

power output: connection adapter for transducers Wx8xx

working position: vertically, cable gland down

IP class: IP65 (after mounting the connection adapter to the Wx8xx sensor)

operating temperature: -30 to +60 °C

weight without batteries: 200 g (including connection adapter)

maximum dimensions: 120 x 93 x 43 mm

DEVICE DIMENSIONS

Inhaltsverzeichnis

Andere Comet Rack & Stand Handbücher

Comet

Comet SP015M Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung