Comet T8148 Bedienungsanleitung

T8148

Programmable indoor transmitter of temperature

and CO2concentration with 4-20mA output

T8248

Programmable indoor transmitter of temperature

and CO2concentration with 0-10V output

Instruction Manual

2 IE-SNC-T81(2)xx-01

General description

The transmitters are designed for online measurement of carbon dioxide concentration and

temperature of air in a building interiors.

device type

construction type

output

T8148

ambient air

4 –20mA

T8248

ambient air

0 - 10V

Principle of CO2concentration measurement is based on Non-Dispersive Infrared Technology

(NDIR). It is maintenance free because of the patented autocalibration feature, compensating for the

effects of aging and therefore a guarantee for outstanding long-term stability. If the device is in

operation permanently, an auto-adjustment will start automatically after 24 hours operation each.

Measured values can be read in „SLOW mode“ (filtered, averaged) or in „FAST mode“ (current

values without averaging). SLOW mode has advantages in applications like climate control because

of filtering short time peaks. As an example exhaled air from an employee passing the sensor could

affect the climate control negatively with a short response time because the control would trigger a

change of the ventilation based on this one-time measurement. On the contrary in „FAST mode“ no

software filter is used for calculating the output value. This fact adds a noise of typ. ±30ppm which

has to be considered in terms of accuracy. Of principle measurement is the measured value of CO2

concentration depends on the value of air pressure - altitude at the installation site. For this reason, it

is suitable for accurate measurement to set the altitude of the installation site by TSensor software -

see below.

Measured values are displayed on dual line LCD display. The visual indication of CO2

concentration is provided by three-color LED.

After power up of the device starts internal test. During this time (about 20s) LCD display shows

(----) instead of CO2concentration value.

Devices with 4-20 mA outputs can be connected to circuitry by means of galvanically isolated or

galvanically non-isolated current loop. Outputs 0 - 10V are galvanically non-isolated.

All transmitter setting is performed by means of the PC connected via the optional SP003

communication cable (not included in delivery). Program TSensor for transmitter setting is

available to download free www.cometsystem.cz/products/reg-TSensor.

Models marked TxxxxZare non-standard versions of the transmitters. Description is not

included in this manual.

Please read instruction manual before the first device connection.

IE-SNC-T81(2)xx-01 3

Device setting from the manufacturer

output 1: T8148 - range 4 to 20 mA corresponds 0 to 2000 ppm

T8248 - range 0 to 10 V corresponds 0 to 2000 ppm

output 2: T8148 - range 4 to 20 mA corresponds 0 to 50ºC

T8248 - range 0 to 10 V corresponds 0 to 50ºC

measurement mode: SLOW

display: switched on

LED indication: up to 1000 ppm lights green LED, between 1000 and 1200 ppm lights

yellow LED and over 1200 ppm lights red LED

altitude: 300 m above see level at the installation site

Modification of the setting is possible to do by means of the PC and TSensor program.

Installation of the transmitter

Devices are designed for indoor applications. It is recommended to mount them on universal

wiring box (common installation box KU68) with using two enclosed mounting screws. For correct

function there is necessary to find proper device place. It shouldn’t be placed at places where it can

be affected by sunshine, near radiators, heating elements and other heat sources, air handlers,

windows, doors, into racks and shelves and similar places. For buildings with less thermal

insulation there is not suitable to place them on external walls of building. If there are

communication conductors placed into conduit, there is strongly recommended make it caulk, to

restrict air flow around device.

For transmitter connection it is recommended to use a shielded cable. Maximum cable lenght of

the current loop is 1200 m, maximum voltage output cable lenght is 15 m. The cable should not be

led in parallel along power cabling. Safety distance is up to 0.5 m otherwise undesirable induction

of interference signals can appear.

Firstly mount the rear part of the device on the wiring box with two screws. Connect cables to

terminals (terminals are self-clamping and can be opened by a suitable screwdriver). By jumpers J1

and J2 select galvanically or non-galvanically isolated current output (T8148), see „Typical

application wiring”. Finish the installation by inserting the front part of the unit.

Installation and electrical wiring should be performed by qualified personal only.

4 IE-SNC-T81(2)xx-01

Device demounting

If there is necessary demount the device, insert flat bladed screwdriver max. 3.5 mm wide from

top side into middle device’s air hole. There is fastening member placed, insert screwdriver beyond

the fastening member about 2 cm deep. Then slightly move screwdriver in arrow direction, it unlock

fastening member and the device is partially opened. Remove the screwdriver and take front part of

device at top.Pull front part with pendulum motion and remove front cover. If there is necessary

remove rear part of the device, please disconnect cables and unscrew two holding screws.

Dimensions

IE-SNC-T81(2)xx-01 5

Typical application wiring

Outputs 4-20 galvanically isolated Outputs 4-20mA galvanically non-isolated

Outputs 0-10V Range of supply voltages and resistor values

Uss . . . . .9 to 30Vdc

Uss1 . . . .9 to 30Vdc

Uss2 . . . .9 to 30Vdc

R1max[Ω] = 50 * Uss1[V] - 450

R2max[Ω] = 50 * Uss2[V] - 450

Rmax[Ω] = 50 * Uss[V] - 450

Rzmin . . 20 kΩ

LCD Info mode

The output range settings can be verified without a use of the computer by

pressing the button on the left side of the device (button is placed behind

small hole - see picture). For button pressing use thin instrument, for example

paper clip.

Upper line of the LCD display shows value of CO2

concentration corresponding to output current 4mA

(output voltage 0V).

Press the button again and upper line of the LCD

display shows value of CO2 concentration

corresponding to output current 20mA (output

voltage 10V).

T8148

T8248

T8148

T8248

6 IE-SNC-T81(2)xx-01

Press the button again to get value of temperature

corresponding to output current 4mA (output voltage

0V).

After next pressing of the button LCD shows value

of temperature corresponding to output current

20mA (output voltage 10V).

Press button again to end info mode and display actual measured value.

Notice: during info mode no measurement and no output current (output voltage) generation

proceed. The transmitter stays at info mode 15 s, and then automatically goes back to measuring

cycle.

Procedure of modification of transmitter adjustment:

Device adjustment is performed by means of the optional SP003 communication cable,

connected to USB port of the PC.

It is necessary to have installed configuration program TSensor on the PC. It is free to

download at www.cometsystem.cz/products/reg-TSensor.

During installation please take care about installation of driver for USB communication cable.

Connect SP003 communication cable to the PC. Installed USB driver detect connected cable

and create virtual COM port inside the PC.

Unscrew four screws of the device lid a remove the lid. If device is already installed to

measuring system, disconnect leads from terminals.

Connect SP003 communication cable to the device. Display must light up, or at least must light

up all symbols for one second (if LCD was switched OFF by program before).

Run installed TSensor program and select corresponding communication COM port (as

described above).

When new setting is saved and finished disconnect the cable from the device and place the lid

back to the device.

Error States of the device

Device continuously checks its state during operation. In case error is found LCD displays

corresponding error code:

Error 0 - first line of LCD displays „Err0“. Check sum error of stored setting inside device’s

memory. This error appears if incorrect writing procedure to device’s memory occurred or if

damage of calibration data appeared. At this state device does not measure and calculate

values. It is a serious error, contact distributor of the device to fix.

T8148

T8248

T8148

T8248

IE-SNC-T81(2)xx-01 7

Error 2 - there is a reading „Err2“ on LCD display. The CO2 concentration measurement error

or temperature error occurred.

Error 3 - there is a reading „Err3“ on LCD display upper line. Error of internal A/D converter

appeared (converter does not respond, probably damage of A/D converter). At this state

device does not measure temperature and relative humidity. This error does not affect CO2

concentration measurement. It is a serious error, contact distributor of the device.

Error 4 - there is a reading „Err4“ on LCD display. It is internal device error during

initialization of CO2sensor. Under this condition device does not measure concentration of

CO2. Value read from device is -9999. CO2sensor is probably damaged. It is a serious error,

contact distributor of the device. This error message is displayed also in case, when the device

is connected to the PC via the optional SP003 communication cable and external power

supply is not used.

Technical parameters

T8148 –temperature and CO2concentration transmitter

Output: 4 to 20 mA

Power voltage: 9 to 30 V

Power consumption: 1W during normal operation

max. 4W for 50 ms with 15 s period

Output in case of error: <3.8 mA or >24 mA

Temperature:

Accuracy: ± 0,5 °C

Range: 0 to +50 ºC

Resolution: 0,1 °C

Response time: t90 < 12 min (air flow approximately 0,3 m/s)

t90 < 25 min (no air flow)

Concentration of CO2:

Accuracy: ± (50 ppm + 2 % of measuring value) at 25°C (77°F) and 1013 hPa

Range: 0 to 2000 ppm

Temp. dependence: typ. 2 ppm CO2/ ºC in the range 0 to 50 ºC (32 to 122°F)

Long term stability: typ. 20 ppm / year

Resolution: 1 ppm

Response time: t90 < 195 s in „SLOW“ measurement mode

t90 < 75 s in „FAST“ measurement mode

T8248 –temperature and CO2concentration transmitter

Output: 0 to 10 V

Power voltage: 15 to 30 V

Power consumption: 0,5W during normal operation

max. 3W for 50 ms with 15 s period

Output in case of error: <-0.1V or >10.5V

8 IE-SNC-T81(2)xx-01

Temperature:

Accuracy: ± 0,5 °C

Range: 0 to +50 ºC

Resolution: 0,1 °C

Response time: t90 < 12 min (air flow approximately 0,3 m/s)

t90 < 25 min (no air flow)

Concentration of CO2:

Accuracy: ± (50 ppm + 2 % of measuring value) at 25°C (77°F) and 1013 hPa

Range: 0 to 2000 ppm

Temp. dependence: typ. 2 ppm CO2/ ºC in the range 0 to 50 ºC (32 to 122°F)

Long term stability: typ. 20 ppm / year

Resolution: 1 ppm

Response time: t90 < 195 s in „SLOW“ measurement mode

t90 < 75 s in „FAST“ measurement mode

Operating conditions

Operating temperature range: 0 to +50°C

Operating humidity range: 5 to 95 %RH (no condensation)

Operating pressure range: 850 to 1100 hPa

Recommended interval of calibration: 5 year (CO2), 2 years (temperature)

Protection: IP20

EMC: EN 61326-1, EN 55011

Storage temperature range: -40 to +60 °C

Storage relative humidity range: 5 to 95 % RH (no condensation)

Storage atmospheric pressure: 700 až 1100 hPa

Dimensions: see dimensional drawings

Weight: approximately 150 g

Material of the case with electronics: ABS

End of operation

Device itself (after its life) is necessary to liquidate ecologically!

Technical support and service

Technical support and service is provided by distributor. For contact see warranty certificate.

You can use discussion forum at web address www.forum.cometsystem.cz.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Comet Sender Handbücher

Comet

Comet T3411 Bedienungsanleitung

Comet

Comet P3116 Bedienungsanleitung

Comet

Comet T5410 Bedienungsanleitung

Comet

Comet T3110 Bedienungsanleitung

Comet

Comet Continental 419F Stücklistenhandbuch

Comet

Comet W0832P Bedienungsanleitung

Comet

Comet W0810P Gebrauchsanweisung

Comet

Comet T3110 Bedienungsanleitung

Comet

Comet W0854P Bedienungsanleitung

Comet

Comet T0213D Bedienungsanleitung

Comet

Comet T0211 Bedienungsanleitung

Comet

Comet T3117 Bedienungsanleitung

Comet

Comet T3319 Bedienungsanleitung

Comet

Comet T 64 Series Gebrauchsanweisung

Comet

Comet IoT Sensor plus W0841 Bedienungsanleitung

Comet

Comet T0310 Bedienungsanleitung

Comet

Comet T3110Ex Betriebsanleitung

Comet

Comet T3113 Bedienungsanleitung

Comet

Comet W0810P Bedienungsanleitung

Comet

Comet T8348 Bedienungsanleitung

Comet

Comet P3116 Gebrauchsanweisung

Comet

Comet T0213 Bedienungsanleitung

Comet

Comet T3311 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung