Comeup ATV-3000 Bedienungsanleitung

ATV/UTV WINCH

Thank you for purchasing a . This manual covers operation and maintenance of

the winch. All information in this publication is based on the latest production information

available at the time of printing.

I. General Safety Precautions

WARNING: FAILURE TO READ AND FOLLOW THE SAFETY INSTRUCTIONS IN

THIS OWNER’S MANUAL BEFORE INSTALLING OR USING YOUR ELECTRIC

WINCH COULD RESULT IN DAMAGE TO YOUR WINCH AND SERIOUS OR FATAL

INJURY!!

Check all safety and environmental conditions prior and during use.

Before use, ensure that you are familiar with all winching performance and operation such as

speed & direction.

A wire rope should be replaced if it shows signs of excessive wear, broken wires, corrosion or any

other defects.

The winches duty rating is S3 (intermittent – periodic)

If the winch fails to pull a load under normal conditions, stop the operation within 30 seconds

otherwise motor damage may occur.

Ensure that the winch is connected to the correct voltage of 12VDC only.

Check that the freespool shifter is in the “Engaged” position during and after use.

Remove the remote control from the winch when not in use.

Do not wrap the wire rope around the load and back onto it self. Always use a strap to ensure that

the wire rope does not fray or kink.

Keep hands and clothes away from the winch, wire rope, and fairlead during operation..

Never unplug the remote control and battery leads when winching a load.

To avoid insufficient power when winching a load, the vehicle should be running and in neutral.

When winching a heavy load, lay a heavy blanket or jacket over the wire rope near to the hook end

If excessive noise or vibration occurs when running, stop the winch immediately and return it for

repair.

If a freespool can’t be properly locked in the “Engaged” position, rotate the drum to have the

freespool coupled to the gear train.

The winch is rated for intermittent

periodic duty.

2.The winch is not to be used to lift, support or otherwise transport personnel.

3.A minimum of five (5) wraps of rope around the drum are necessary to support the

rated load.

4.The rated line pull of the winch must be powerful enough to overcome the added

resistance caused by whatever the vehicle is stuck in.

5.Never operate the winch under water.

6.Operate the winch cable in and cable out at no load after a winch was ingressed by

water.

WARNING

II. Performance Data

Specifications Line Pull and Rope Capacity

Model ATV-3000 UTV-4000 Model ATV-3000

UTV-4000

Line Pull

(first layer) 1,360 kg / 3,000 lb

1,814 kg / 4,000 lb

Line pull ( kg / lb) 1,363 / 3,000

1,814 / 4,000

Line speed (mpm / fpm)

2.6 / 8.5 2.6 / 8.5

Line Speed

(first layer, no load)

7.6 mpm / 24.9 fpm

6.0 mpm / 19.7 fpm

1st layer

Rope cap. ( m / ft ) 2.6 / 8.5 3.3 / 10.8

Amp.

Draw

12V 230A 230A Line pull ( kg / lb ) 1,170 / 2,590

1,694 / 3,735

Line speed (mpm / fpm)

2.9 / 9.5 3.0 / 9.8

Type Permanent magnet

2nd layer

Rope cap. ( m / ft ) 5.7 / 18.7 7.2 / 23.6

Line pull ( kg / lb ) 1,030 / 2,270

1,446 / 3,188

Motor

Input

12V

800 w / 1.0 hp 800 w / 1.0 hp

Line speed (mpm / fpm)

3.3/10.8 3.5 / 11.5

Type 3 stage planetary

3rd layer

Rope cap. ( m / ft ) 9.2 / 30.2 11.9 / 39.0

Gear

Train

Ratio 145:1 184:1 Line pull ( kg / lb ) 920 / 2,030

1,261 / 2,780

Freespool Sliding shaft gear Line speed (mpm / fpm)

3.8 4.0 / 13.1

Brake Dynamic and mechanical

4th layer

Rope cap. ( m / ft ) 13.1/ 43 15.2 / 50

Line pull ( kg / lb ) 830 / 1,830

＊

Control Remote switch &

trigger switch Remote switch

Line speed (mpm / fpm)

4.2 ＊

Type A7 x 19 aircraft galvanized

5th layer

Rope cap. ( m / ft ) 15.2 /50 ＊

Length 15.2 m / 50 ft 15.2 m / 50 ft

Wire

Rope

Size 4.8 mm / 3/16 in 5.5 mm / 7/32 in

Drum size 55mm×75mm 55mm×119mm

Line Speed and Amp. Draw

(First layer of wire rope on the drum)

Model ATV-3000 UTV-4000

Line Pull Line Speed Amp. Line Speed Amp.

kg lb mpm fpm 12V mpm fpm 12V

0 0 7.6 24.9 15 6.0 19.7 20

230 500 6.3 20.7 40 3.9 12.8 45

450 1,000 4.9 16.1 70 3.4 11.2 70

680 1,500 4.3 14.1 100 3.1 10.2 90

900 2,000 3.7 12.1 140 2.9 9.5 120

1,140 2,500 3.1 10.2 180 2.7 8.9 150

1,363 3,000 2.5 8.2 230 2.4 7.9 180

1,588 3,500 ＊＊＊2.2 7.2 210

1,814 4,000 ＊＊＊2.0 6.6 230

Your winch will pull your ATV/UTV up or down in a ramp, it also help another ATV/UTV

or a load if it is anchored in a stationary position.

Main Components

Ⅲ

ⅢⅢ

Ⅲ. Installation





Complete kit installation

To install the complete kit, you need to amount the winch, roller fairlead, solenoid, remote socket

and trigger switch. Read and understand the following instruction to choose the proper mounting

locations.

1: Winch Ass'y with Wire Rope

2: Remote Control

3: Trigger Switch Ass'y (ATV-3000 only)

4: Remote Socket

5: Solenoid CES-2012

6: 6 Gauge Battery Lead

7: 4 Way Roller Fairlead

8-1 Mounting Plate (for ATV-3000)

8-2 Mounting Plate (for UTV-4000)

9-1 Snatch Block (for ATV-3000)

9-2 Snatch Block (for UTV-4000)

10: Handlebar Hardware (ATV-3000 only)

11: Mounting Hardware





Winch & Roller Fairlead Mounting

1. It is very important that the winch shall be

mounted on a flat hard surface in order to make

sure the motor, drum and gearbox housing are

aligned correctly.

2. If a different mounting plate is used, the thickness

shall be 5 mm (3/16”). If different hardware

is used, it must be SAE grade 8 minimum.

3. Four (4) included M8x 25L Grade 8.8 High

Tensile Steel Bolts must be used for

securing the

winch on the mounting plate in order to sustain the loads imposed on the winch mounting.

4. Two (2) included M8 x 20L Grade 8.8 High Tensile Steel Bolts must be

used for

securing the roller fairlead on the mounting plate.





Solenoid Mounting

1. It disconnects your winch from the power source when the vehicles is not in use

2. It should be mounted close to the battery and keep the location from all metal structures.





Remote Socket Mounting

1.Determine the mounting location for the remote socket.

2.Drill three holes on a plate and install.

ATV-3000 UTV-4000





Trigger Switch Mounting (ATV-3000 only)

Handlebar mounted trigger switch can be operated without removing your hand from the grip.





wiring Diagram

Ⅳ

ⅣⅣ

Ⅳ. Operation





Cable In and Out

1). To determine “ Cable Out “, trigger to the “Out” position

2). To determine “ Cable In “, trigger to the “In” position

3). To stop winching, release the trigger level

Freespool Function

The freespool allows rapid pay-out of the wire rope for hooking onto a load or anchor points and is

operated by a freespool shifter located on the end of the winch.

1). To engage the freespool, turn the freespool shifter counter-clockwise to the “Engaged” position.

The winch is now ready for pulling.

2). To disengage the freespool, turn the freespool shifter clockwise to the “Disengaged” position.

Wire rope can now be free spooled off the drum.

Ⅴ

ⅤⅤ

Ⅴ. Maintenance





Wire Rope Replacement

Before installing a new wire rope, wrap the end of the wire rope with tape to prevent fraying. Wind

the wire rope on the drum by pull a force to keep the tension constant. Never use a wire rope of a

different size or material and only use aircraft grade wire ropes.

1). Disengage the freespool.

2). Spool the old wire rope, and then remove it from the drum.

3). Have horizontal roller and bolts apart from the roller fairlead, then place the replacement wire rope

through the roller fairlead throat, pass below the drum, and insert it into the hole on the drum core.

4). Use a hex wrench to tighten the screw downwards to secure the wire rope.

5). Tighten the horizontal roller and bolt of roller fairlead

6). Wear leather gloves and use a strap when guiding the wire rope off the drum.

7). It is very important that the winch shall be mounted on a flat surface , with the wire rope feeding

form the bottom of the drum.

8). To rewind wire rope on the drum correctly , it is necessary to keep a slight load on the wire rope

while cable in.

(Disengaged)

(Engaged) (Disengaged)





Lubrication

All moving parts in the winch are permanently lubricated at the time of assembly. Under normal

conditions factory lubrication will suffice. If re-lubrication is necessary after repair or disassembly

use a marine type grease.





Maintenance Schedule

Carry out all inspections listed below on schedule and inspections are divided into Daily, Monthly

and 3 Monthly. Clean all connections because corrosion on electrical connections will reduce

performance or may cause a short.

Classification of check

Periodical

Daily

One

month

Three

month

Item Checking method Checking reference

Complete winch Operate the winch in and out

Minimum corrosion of the

internal motor components

Installation

Mounting bolts & alignment.

Bolts tension & wear. Tightened and aligned

Working Manual Reasonable actuation



Remote

control

Wearing in contact points Visual. Free of wear or damage.

Broken strands Visual, measuring (monthly)

Less than 10%

Decrease in rope diameter Visual, measuring (monthly)

7% of nominal diameter max



Wire rope

Deforming or corrosion and

fastening condition of end

Visual No existence of abnormalities

Freespool Wear in spring Visual evidence of wear Free of wear or damage.

Motor Staining, damage Visual evidence of wear No existence of abnormalities

Wearing of lining Visual evidence of wear Free of wear or damage.



Brake

Performance Visual Reasonable actuation

Gear train Damage, wearing Visual evidence of wear Free of wear or damage and

distortion.

Ⅵ

ⅥⅥ

Ⅵ. Trouble Shooting

When the winch fails to operate after several attempts, or if there is any fault operation while

winching, check followings.

Symptom Possible Cause Remedy

Cut circuit or loosing Check battery cable.

Weak battery or insufficient power Recharge or replace battery

Damaged over load protector Replace over load protector

Loose connection of wirings Checking all wirings

Damaged or stuck solenoid Replace solenoid

Defective remote control Check winch operation with an

auxiliary switch

Winch will not operate

Damaged motor or worn carbon brush Replace motor or carbon brush

Broken wiring or bad connection Reconnect or replace wiring

Damaged or stuck solenoid Replace solenoid

Switch inoperative Replace switch

Motor runs in one

direction.

Dropt or lost wiring Replace wiring and tighten.

Freespool not disengaged Engaged freespool

Damaged brake or freespool ass’y Replace brake or freespool ass’y

Damaged drum bushing Replace drum bushing

Drum will not free

spool.

Damaged gear box Replace gear box

Damaged or inoperative pressed spring

Replace pressed spring

Disengaged freespool Engaged

Damaged output shaft Replace output shaft

No brake

Damaged 1st shaft Replace 1st shaft

Brake distance is too

long Worn or damaged brake Replace or adjust brake

Motor leads crossed Reverse electrical connections to

motor

Solenoid control crossed Reverse black and red wires on the

solenoid

Winch runs opposite

direction

Remote control or trigger switch crossed

Reverse electrical connections

Long period of operation Stop operation to have it cooled

Over-load Reduce load

Motor runs extremely

hot

Damaged or inoperative brake Replace or repair brake

Ⅶ

ⅦⅦ

Ⅶ. Replacement Parts List





ATV-3000

No.

Description No.

Description

1 Motor 1

Freespool block 1

Wire rope 1

2 Motor support rack 1

Friction block 1

Roller fairlead 1

3 Gearbox support rack 1

Tie bar 2

Snatch block 1

4 Drum bushing 2

Plain washer 1

Remote control 1

5 Drum 1

Anti-leakage packing 2

Solenoid 1

6 Connector A 1

Bearing 1

Remote socket 1

7 Connector B 1

Dented retaining ring 1

Battery lead 1

8 Brake spring 1

Dented retaining ring 1

Battery lead 1

9 1st shaft 1

Hex bolt 4

Battery lead 1

Pressed spring 1

Hex bolt 3

Battery lead 1

2nd stage carrier 1

Spring washer 4

Mounting hardware 1

1st stage carrier 1

Screw 1

Cable tie 10

Ring gear 1

Foot print 1

Handlebar hardware 1

Freespool base 1

Base plate 1

Trigger switch 1

Freespool shifter 1

1st pinion 1

Spring Packing 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Comeup Winde Handbücher

Comeup

Comeup CWS-230 Bedienungsanleitung

Comeup

Comeup DV-6s Bedienungsanleitung

Comeup

Comeup DV-2500i Bedienungsanleitung

Comeup

Comeup Seal Gen2 16.5s Bedienungsanleitung

Comeup

Comeup CEP-1000-14M Bedienungsanleitung

Comeup

Comeup Rhino 12 Bedienungsanleitung

Comeup

Comeup Walrus 20.0 Bedienungsanleitung

Comeup

Comeup CHAMPIONSHIP WINCH Bedienungsanleitung

Comeup

Comeup DV-9 Bedienungsanleitung

Comeup

Comeup Rhino 15 Pro Bedienungsanleitung

Comeup

Comeup DV-3500i Bedienungsanleitung

Comeup

Comeup DS-9.5i Bedienungsanleitung

Comeup

Comeup Seal Gen2 12.5rs Handbuch

Comeup

Comeup CWG-10077 Bedienungsanleitung

Comeup

Comeup CWG-30375 Bedienungsanleitung

Comeup

Comeup CP-500 Bedienungsanleitung

Comeup

Comeup CP-300 Bedienungsanleitung

Comeup

Comeup DH-300 Bedienungsanleitung

Comeup

Comeup Seal Gen2 12.5rs Bedienungsanleitung

Comeup

Comeup CWG-31500 Bedienungsanleitung

Comeup

Comeup DV-9 Bedienungsanleitung

Comeup

Comeup CP-250 Bedienungsanleitung

Comeup

Comeup CWL-301 Bedienungsanleitung

Comeup

Comeup WT-180 Bedienungsanleitung

Beliebte Winde Handbücher anderer Marken

WARRIOR

WARRIOR Trojan 40PUS12 Kurzanleitung

SVERO

SVERO 16 Bedienungsanleitung

Warrior Winches

Warrior Winches C10000NH Bedienungsanleitung

Badland Winches

Badland Winches 68146 Bedienungsanleitung

Bush

Bush II Series Bedienungsanleitung

Badland

Badland APEX 5500 Bedienungsanleitung

Quadratec

Quadratec Q9000 Synthetic Handbuch

C-Max

C-Max VIGO Bedienungsanleitung

Orvea

Orvea Italwinch 805 Bedienungsanleitung

Prowinch

Prowinch PWJTHF300 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LD2000-A Bedienungsanleitung

Topex

Topex 97X080 Bedienungsanleitung

Eastbound

Eastbound MotoWinch 1707001 Bedienungsanleitung

Runva

Runva EWD8000 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Installationsanleitung

Granit

Granit 11157675 Bedienungsanleitung

TREX

TREX TB75 Bedienungsanleitung

Badland

Badland ZXR 2500 Bedienungsanleitung