Commodore Amiga A500 Produkthandbuch

Commodore®Amiga®

A500/A2000

Technical Reference

Manual

This document may not, in whole or part, be copied, photocopied, reproduced,

translated or transferred to any electronic medium or machine readable form

without prior consent, in writing, from Commodore-Amiga, Inc.

Amiga is a registered trademark of Commodore-Amiga, Inc.

Commodore and CBM are registered trademarks of Commodore Electronics Limited.

Hayes is a registered trademark of Hayes Microcomputer Products, Inc.

IBM is a registered trademark of International Business Machines Corporation,

Macintosh is a trademark of Apple Computer, Inc.

DISCLAIMER

THE INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED

OR IMPLIED. THE ENTIRE RISK AS TO THE ACCURACY OF THE INFORMATION HEREIN IS

ASSUMED BY YOU. COMMODORE-AMIGA DOES NOT WARRANT, GUARANTEE. OR MAKE ANY

REPRESENTATIONS REGARDING THE USE OF. OR THE RESULTS OF THE USE OF, THE

INFORMATION IN TERMS OF CORRECTNESS, ACCURACY, RELIABILITY, CURRENTNESS. OR

OTHERWISE. IN NO EVENT WILL COMMODORE-AMIGA, INC. BE LIABLE FOR DIRECT, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY DEFECT IN THE

INFORMATION EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME

LAWS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES OR LIABILITIES

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION OR EXCLUSION MAY

NOT APPLY.

Schematics represent current machine which is subject to change without notice.

Credits

The material for this manual was produced by Engineering. Documentation,

and Technical Support staff at Commodore West Chester, Commodore

Braunschweig, and Commodore-Amiga. Individuals contributing major por-

tions of information and input are Dave Haynie, Jeff Porter, Phil Lindsay,

Carolyn Scheppner, Lisa Siracusa. George Robbins. Andy Finkel. Eric

Cotton, Jeff Boyer, Steve Ahlbom, Steve Beats, Dieter Preiss, Bernd

Assmann, and Torsten Burgdorf.

This manual was compiled and edited by Steve Finkel.

Manual design by Jo-Ellen Temple and Wilson Harp.

A2000/A500 Technical Reference Manual

Table of Contents

Section 1 Summary of Differences

Section 2 System Block Diagrams

Section 3 Amiga Expansion

3.1 Designing hardware for the Amiga Expansion

Architecture

3.2 Driver Documentation

3.3 Software for Amiga Expansion

3.4 Amiga Expansion Connectors

100 Pin

86 Pin

Video Slot

101

Section 4 PC Bridgeboard

4.1 Description of the PC/XT emulator for the Amiga 2000

109

4.2 BIOS entry points

121

4.3 Janus library

131

Section 5 Amiga Hard Disk/SCSI Controller

159

Section 6 Custom Chips

Fat Agnus Chip

187

8520 Chip

213

Section 7 Miscellaneous Hardware Information

223

7.1 Clock/calendar registers

225

7.2 Power budgets

229

7.3 A2000 PAL equations

235

7.4 B2000 Jumpers

Appendix A. Diagrams

A-1 Backplane Example

A-1

A-2 PIC Example

A-2

A-3 A500 Exterior (86-pin expansion connector)

A-3

A-4 Amiga 2000 Expansion Board Layout

A-4

A-5 Amiga 2000 Form Factor

A-5

A-6 Amiga 2000 Video Card

A-6

A-7 86-Pin Slot Expansion Board

A-7

A-8 A2000/B2000 Keyboard Connector Pinout

A-8

A-9 Amiga 500/2000 Mouse Diagram and Pinout

A-9

Appendix B. Schematics

A2000 Schematics

A2000-1

B2000 Schematics

B2000-1

A500 Schematics

A500-1

Section 1

Summary of Differences

KICKSTART IN ROM

This manual presents technical documentation for three different

Amiga models, comparing them to the original Amiga, referred to as

model A1000. Technical information included in this manual is rel-

evant for the following Commodore Amiga models:

●the Amiga 500 (A500), a low-cost version of the origi-

nal Amiga computer, software-compatible with the

A1000. Unlike the A1000, the A500 has an integrated

keyboard, provision for internal memory expansion up

to 1 megabyte, new-style hardware connectors, and

Kickstart code in ROM.

Two versions of the Amiga 2000:

●the A2000 is software-compatible with the A1000 and

has internal slots, real time clock/calendar and new-

style hardware connectors.

●the B2000, the cost-reduced version of the Amiga

2000, features some different custom chips, but is

otherwise similar to the A2000.

The B2000 is still under development, and the information present-

ed in this document is subject to change. The information included

on the B2000 is intended to aid developers in designing software

and peripherals that are applicable for both the current and

upcoming version of the Amiga 2000.

Unless differences are specifically noted, information presented for

the A2000 also holds true for the B2000. The differences between

the two Amiga 2000 models are mainly hardware differences which

will affect peripheral design, but not the way the computers function

with software. Section 2 contains system block diagrams for all

three new Amiga models.

Both the Amiga 2000 and the Amiga 500 feature version 1.2 of

Kickstart built into ROM. Kickstart 1.2 (currently version 33.180)

boots automatically when the Amiga is turned on.

EXTRA KEYS ON THE

KEYBOARD

RAW KEY CODES ON

THE KEYBOARD

Both the Amiga 2000 and 500 feature 94-key keyboards, as com-

pared to the A1000's 89-key keyboard. (The European versions of

the keyboards have 96 keys.) The new keys are all located on the

numeric keypad, and include:

KEY SCAN CODE

Left parentheses ( $5A

Right parentheses ) $5B

Slash / $5C

Asterisk * $5D

Plus + $5E

In PC mode on the Amiga 2000 (using a Bridgeboard), these keys

assume typical PC functions, including Number lock (left parenthe-

sis), Print screen (asterisk) and Scroll lock (right parenthesis).

On some keyboards, the left Amiga key has been replaced by the

Commodore key. This key performs identically in either case.

Keyboard Layout Showing Raw Key Codes

45 50 51 52 53 54 55 56 57 58 59

3F 4A

3D 3E

14 15 16 17 18 19 1A 1B42 10 11 12 13

0D 41 46 5F 5B 5C 5D

05 06 07 08 09 0A 0B 0C00 01 02 03 04

67 654064 66

1D 1E

2E 2F 5E

0F 3C

4C63 28 29 2A 2B

20 21 22 23 24 25 26 2762

3A 61 4F 4D 4E33 34 35 36 37 38 3960 30 31 32

Figure 1.1 Key Codes

Note: On the U.S. keyboard, the keys with codes 44 and 60 are

extended to include the European keys with codes 2B and 30,

respectively. Also note that England uses the U.S. rather than

the European keyboard, but not the U.S. keymap.

See Table 1-1 at the end of this section for a table of the raw key

codes.

EXTERNAL SYSTEM I/O

RS232 and MIDI Port

12345678910111213

141516171819202122232425

This section describes each I/O interface in detail, and some of the

tradeoffs made with respect to A1000 compatibility.

The Amiga 2000 and Amiga 500 have differences in the serial and

parallel ports from the Amiga 1000, the main difference being

changes in the sex of each port (changing the serial to female and

the parallel to male), which allows the new Amigas to use standard

interface cables.

The RS232 connector on the A500 and A2000 is form fit and

function identical to a Commodore PC-10/20 with a few

exceptions. This is the OPPOSITE sex connector from the

A1000. The connector is a shielded male DB25P connector. The

A1000 supplies various non-standard RS232 signals on the DB25

connector. These non-standard signals were removed wherever

possible. The RS232 connector is NOT physically compatible with

some MIDI interfaces but is compatible with the Amiga

Modem/1200 RS {model 1680). Below is a comparison chart

between the RS232 standard, a Hayes Smart-modem standard, the

A1000 RS232, and the new Amiga 500/2000 RS232 connector.

PIN RS232 A1000

A500/

A2000 PC10 HAYES® DESCRIPTION

1 GND GND GND GND GND Frame

round

2 TxD TxD TxD TxD TxD Transmit Data

3 RxD RxD RxD RxD RxD Receive Data

4 RTS RTS RTS RTS

—

uest to send

5 CTS CTS CTS CTS CTS Clear to send

6 DSR DSR DSR DSR DSR Data set read

7 GND GND GND GND GND Si

nal

round

8 DCD DCD DCD DCD DCD Carrier detec

9—

—

+ 12v + 12v

—

+ 12 volt

ower

10 —

—

- 12v - 12v

—

- 12 volt

ower

11 —

—

UDO

—

udio out

12 S.SD

—

SI S

eed Indicate

13 S.CTS

—

14 S.TxD -5Vdc —

—

- 5 volt

ower

15 TxC

UDO —

—

udio out

16 S.RxD

UDI —

—

udio in

17 RxC EB —

—

Port clock 716KHz

18 — INT2*

UDI

—

Interru

t line/Audio in

19 S.RTS

—

20 DTR DTR DTR DTR DTR Data terminal read

21 S

D+5Vdc—

—

+ 5 volt

ower

22 RI

—

RI RI RI Rin

indicator

23 SS + 12Vdc —

—

+ 12 volt

ower

24 TxC1 C2* —

—

3.58MHz clock

25 — RESB* —

—

Buffered s

stem

Centronics Port

12 34567891011 12 13

14 15 16 17 18 19 20 21 22 23 24 25

Video Output

As you will notice, the A500 and 2000 deletes clocks and interrupt

lines from the A1000. The +/-5Vdc and reset lines are also deleted.

The +/- 12Vdc lines are identical to a PC10/20.

The following signals (formerly on the RS232 connector) can be

found on other connectors:

ResB = parallel connector

C2 = video connector

The Centronics port also has some non-standard signals. Below is a

table comparing the A1000 Centronics port with the A500/A2000

Centronics port. Again, this is the opposite sex from the A1000

and the same sex connector as an IBM®-PC (i.e., a female DB25

connector).

PIN A1000 A500/A2000 PC10

1 DRDY* STROBE* STROBE*

2 Data O Data O Data O

3 Data 1 Data 1 Data 1

4 Data 2 Data 2 Data 2

5 Data 3 Data 3 Data 3

6 Data 4 Data 4 Data 4

7 Data 5 Data 5 Data 5

8 Data 6 Data 6 Data 6

9 Data 7 Data 7 Data 7

CK*

11 BUSY

(

data

)

BUS

12 POUT

(

clk

)

POUT POUT

13 SEL SEL SEL

14 GND + 5v

ullu

UTOFDXT*

15 GND NC ERROR*

16 GND RESET* INIT*

17 GND GND SLCT IN*

18-22 GND GND GND

23 + 5v GND GND

24 NC GND GND

25 Reset* GND GND

The A500 and A2000, like the A1000, use a DB23 video connector.

This 23 pin connector contains all the signals necessary to work with

a Genlock, but the current Genlock will need to be redesigned in or-

der to meet the physical requirements of the A500 and A2000, in

Mouse and Joystick

Ports

A500 Expansion Port

A500 RAM Expansion

A500 Power Supply

Connector

stead of the A1000. An A500 genlock will also have to supply its

own power. Power will not be provided for the Genlock. All signals

on the 23 pin connector are the same except for the power.

In addition to the 23 pin video connector, the A500/B2000 provides

a monochrome composite video output, unlike the A1000. This pro-

vides the capability of using a low-cost, high persistence mono-

chrome monitor with the A500 for viewing 640 x 400 interlaced

video without as much flickering.

Power is provided for the A520 modulator and composite video

adapter.

The mouse and joystick ports of the A500 and A2000 are identical

to the A1000, except that the current limiting protection circuitry

has been eliminated. The A500 and A2000 use a different mouse

than the one the A1000 uses. A diagram and information on this

mouse is included in Appendix A of this manual.

The expansion port is electrically compatible with the A1000, but

because of its physical location, it cannot accept any A1000

expansion peripherals without some further adapter. Power is

supplied to this connector, but only enough for a ROM cartridge.

The exact pinout of this 86 pin edge connector appears later in this

document,in the section of Amiga expansion. The A500 diagram in

Appendix A shows the new positioning of this port (relative to

A1000) and the pin numbers.

Associated with the built-in 512KB of RAM is a header socket to al-

low an additional 512KB of RAM and a battery backed-up real time

clock board to be added. This small PCB (the A501 RAM Expansion

Cartridge) can easily be installed by the user. The clock in this unit

functions the same as that built into the A2000, which is reviewed

in Section 7-1.

The A500 power supply connector is similar to that of the C128.

The pinout of the square 5 pin DIN connector is as follows:

PIN SIGNAL

1 + 5Vdc @ 4.3A

2 Shield Ground

3 + 12Vdc@ 1.0A

4 Signal Ground

5 -12Vdc @ .1A

External Disk Interface

Connector

The 23 pin D-type connector with sockets (DB23S) at the rear of the

Amiga is nominally used to interface to MFM devices.

The second disk drive port is similar to the A1000, and is therefore

compatible with the 1010 or the 1020 disk drive. The CPU will

power one external 1010 disk drive.

External Disk Connector Pin Assignment

Pin Name Dir Notes

1 RDY* I/O If motor on, indicates disk

installed and up to speed.

If motor not on, Identification

mode. See below.

2 DKRD* I MFM input data to Amiga.

3GND

4GND

5GND

6GND

7GND

8 MTRXD* OC Motor on data, clocked into

drive's motor on flip flops by the

active transistion of SELxB*.

Guaranteed setup time is 1.4

μsec

Guaranteed hold time is 1.4

μsec.

9 SEL2B*/SEL3B

0C A500:Select drive 2/A2000:

Select drive 3.

10 DRESB* OC Amiga system reset. Drives

should reset their motor on flip

flops and set their write protect

flip flops.

11 CHNG* I/0 Note: Nominally used as an open

collector input. Drive's change

flop is set at power-up or when

no disk is installed. Flop is reset

when drive is selected and the

head stepped, but only if a disk is

installed.

12 5V 270 ma maximum; 410 ma

surge.

When below 3.75V, drives are

required to reset their motor on

flops, and set their write protect

on flops.

13 SIDEB* 0 Side 1 if active, side 0 if inactive.

14 WPR0* I/O Asserted by selected, write

protected disk.

15 TKO* I/0 Asserted by selected drive

when read/write head is

positioned over track 0.

16 DKWEB* OC Write gate (enable) to drive.

17 DKWDB* OC MFM output data from

Amiga.

18 STEPB* OC Selected drive steps one

cylinder in the direction

indicated by DIRB.

19 DIRB OC Direction to step the head.

Inactive to step towards

center of disk (higher

numbered tracks).

20 SEL3B*/

Not Used

OC A500: Select drive 3/A2000:

Not used.

21 SEL1B/SEL2B OC A500: Select drive 1/A2000:

Select drive 2.

22 INDEX* I/O Index is pulse generated once

per disk revolution, between

the end and beginning of

cylinders. The 8520 can be

programmed to conditionally

generate a level 6 interrupt to

the 68000 whenever the

INDEX* input goes active.

23 + 12V 160 ma maximum; 540 ma

surge.

Note: * in signal name denotes active low signal.

External Disk Connector Identification Mode

An identification mode is provided for reading a 32 bit serial identifi-

cation data stream from an external device. To initialize this mode,

the motor must be turned on then off. See pin 8, MTRXD* for a

discussion of how to turn the motor on and off. The transition from

motor on to motor off reinitializes the serial shift register.

After initialization, the SELxB* signal should be left in the inactive

state.

Now enter a loop where SELxB* is driven active, read serial input

data on RDY* (pin 1), and drive SELxB* inactive. Repeat this loop a

total of 32 times to read in 32 bits of data. The most significant bit

is received first.

Andere Handbücher für Amiga A500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Commodore Desktop Handbücher

Commodore

Commodore Plus/4 Bedienungsanleitung

Commodore

Commodore Plus/4 Bedienungsanleitung

Commodore

Commodore Amiga Referenzhandbuch

Commodore

Commodore VIC-20 Betriebsanleitung

Commodore

Commodore PC 10-1 Bedienungsanleitung

Commodore

Commodore 8000 Series Bedienungsanleitung

Commodore

Commodore COLT 286 Bedienungsanleitung

Commodore

Commodore Plus 4 Bedienungsanleitung

Commodore

Commodore C-NET 128 v7.0 Bedienungsanleitung

Commodore

Commodore Amiga 1200 Bedienungsanleitung

Commodore

Commodore VIC-20 Bedienungsanleitung

Commodore

Commodore C16 Bedienungsanleitung

Commodore

Commodore 64 Bedienungsanleitung

Commodore

Commodore C16 Bedienungsanleitung

Commodore

Commodore 4016 Bedienungsanleitung

Commodore

Commodore AMIGA 2500 Referenzhandbuch

Commodore

Commodore 128 Bedienungsanleitung

Commodore

Commodore Amiga A1000 Bedienungs- und Wartungshandbuch

Commodore

Commodore C16 Bedienungsanleitung

Commodore

Commodore AMIGA 1060 SIDECAR Bedienungsanleitung

Commodore

Commodore PC 10-1 Bedienungsanleitung

Commodore

Commodore SX-64 Bedienungsanleitung

Commodore

Commodore 16 Bedienungsanleitung

Commodore

Commodore 64 Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung