CommScope BUDI-M-TH Bedienungsanleitung

BUDI-M-TH

INSTALLATION INSTRUCTION

Building distributor

Box

• SC/APC adapters (100 pieces)

• = SC/APC 2 m pigtails (96 pieces)

• Foam (1 mm)

• Hook and loop fastener (6 pieces)

Suitable for FTTH applications where easily pre-connectorized splitters

modules can be built-in. The box is designed to accommodate both

spliced and connectorized riser cable solutions, while maximizing the

box’s capacity.

Looped cable accessories

Seals

Wrap-around cable seals

Sealblock 6 x 10 mm

Cable diameter (mm) Foam (± 5 mm)

3 95

4 90

5 80

6 75

7 70

8 60

9 50

10 40

Sealblock 6 x 15 mm

Cable diameter (mm) Foam (± 5 mm)

9 125

10 115

11 105

12 95

13 85

14 70

15 60

Sealblock 3 x 20 mm

Cable diameter (mm) Foam (± 5 mm)

14 155

15 140

16 125

17 110

18 95

19 85

20 75

Sealblock 24 x 7 mm

Cable range A 1.8 – 5 mm

B 5 – 7 mm

Inline seal 1 x 18

To use in ports S6-S7 only

Cable range 3 – 18 mm

Standard gland

PG 16

PG 21

PG 29

PG 29 (PTS 24)

2 Kit content

1. Introduction

TC-1242-IP

Rev A, Apr 2017

www.commscope.com

3.1 Install adapters into top 4 trays. The bottom tray is used for the

loose tube to be spliced to the splitter inputs.

3 Installation of feeder cable

3.2 Use the two guiding pins found on the inside of the box cover

to open the ports. Cut out the plastic.

3.3 Make a window cut of 2.7 m.

3.4 Prepare the two cable brackets as shown.

3.5 Apply the hook and loop fastener.

3.6 Cut strength members to the length of 5.5 cm and secure them

under the two metal plates.

3.7 Secure the looped cable with the two hose clamps.

3.8 Apply the foam around the looped cable.

3.9 Install the looped cable into the ports and close the seal.

3.10 Install the second cable bracket and secure together with two

pins (slide through holes).

3.11 Install the edge protection.

3.12 Take out one loose tube.

3.13 Use a wedge to support the trays. Store the loop on the looped

bracket below the trays and secure the loop with two tie-wraps.

4 Installation of OCM6 splitter

3.15 Apply the foam and secure the loose tubes together with the

two tie wraps. Select the fibers to be spliced to the inputs of the OCM6

splitters and cut them off (do not cut the feeder side).

3.14 Mark the loose tube at marked position and shave the tube

(make sure that the unshaved part of the tube is long enough to be

able lift the tray).

3.16 Store the unused fibers into the tray as shown.

4.1 Install the OCM6 splitter. Up to the three OCM6 splitters can

be installed.

4.2 Guide the input of the OCM6 splitter under the base plate

towards to the bottom tray.

4.3 Strip the OCM6 splitter input at the marked position, apply the

foam and secure with the tie wrap.

Splice the fibers and store the overlength into the tray.

4.4 Install the cover and secure with the two screws.

4.5 Guide the outputs of the OCM6 splitters through the wire

saddle.

4.6 Connect the outputs of the OCM6 splitter to the designated

adapters.

4.7 The unused outputs of the OCM6 splitter can be parked at the

bottom of the box in the parking lots. Use the hook and loop fastener for

better fiber arrangement.

5 Installation of riser cable

5.1 Prepare the seal port.

5.2 Prepare the riser cable to be installed into the box.

5.3 Install the riser cable into the box on the metal bracket and

secure with the two tie-wraps.

5.4 Close the seal.

5.5 Install the 900 µm pigtails into the tray.

5.6 Secure the riser cable fibers into the tray with the foam and two

tie-wraps.

5.7 Strip the pigtails at the marked position.

5.8 Splice all the fibers and store the overlength into the tray.

5.9 Install the cover onto the tray and secure with the two screws.

All trademarks identiﬁed by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc.

This document is for planning purposes only and is not intended to modify or supplement any speciﬁcations or warranties relating to

CommScope products or services.

This product is covered by one or more U.S. patents or their foreign equivalents. For patents, see:

www.commscope.com/ProductPatent/ProductPatent.aspx.

To ﬁnd out more about CommScope® products, visit us on the

web at www.commscope.com

For technical assistance, customer service, or to report any

missing/damaged parts, visit us at:

http://www.commscope.com/SupportCenter

Andere CommScope Kabelbox Handbücher

CommScope

CommScope Rapid Fiber 1RU Bedienungsanleitung

Beliebte Kabelbox Handbücher anderer Marken

FBS

FBS C01 Bedienungsanleitung

peerless-AV

peerless-AV IBA2 Leitfaden

Extron electronics

Extron electronics Cable Cubby 1202 Bedienungsanleitung

peerless-AV

peerless-AV IBA3AC Leitfaden

Channel Vision

Channel Vision AFFINITY P-0328 Bedienungsanleitung

Minebea Intec

Minebea Intec IE11357 Bedienungsanleitung

StarTech.com

StarTech.com BOX4CABLE Bedienungsanleitung

Commercial Electric

Commercial Electric 5053-WH Bedienungsanleitung

Motorola

Motorola DCT6412 DUAL-TUNER DVR AND HD SET-TOP - MICROSOFT... Montageanleitung

Renkforce

Renkforce 1395556 Bedienungsanleitung

Huawei

Huawei FAT9102SD-32G Bedienungsanleitung

VISSEM Electronics

VISSEM Electronics Opticube VSOF-OTB-E Bedienungsanleitung

Beta

Beta 1844 15-H05/SCK Bedienungsanleitung

FSR

FSR FL-1550 Bedienungsanleitung

Renkforce

Renkforce 1674559 Bedienungsanleitung

Minebea Intec

Minebea Intec PR 6130/64Sa Bedienungsanleitung

KS Tools

KS Tools efuturo Wallbox Bedienungsanleitung

Chatsworth Products

Chatsworth Products Evolution Bedienungsanleitung