Comnet FVT801 Bedienungsanleitung

Mechanical Installation Instructions

Figure 1– Dimensions are for a standard ComNet™ one slot module.

Rack Module:

The unit is designed to be installed in the ComNet 19-inch (483-mm) EIA standard card-cage rack, the C1-US,

C1-EU, or the C1-CH. Follow these guidelines to install rack cards after performing module setup procedures.

C1-US, C1-EU, or the C1-CH Card Cage Racks

CAUTION: Although the units are hot-swappable and may be installed without turning power off to the rack, ComNet

recommends that the power supply be turned off and that the rack power supply is disconnected from any power

source. Note: Remove electrical connector before installing in card cage rack.

1. Make sure that the card is oriented right side up, and slide it into the card guides in the rack until the edge

connector at the back of the card seats in the corresponding slot in the rack’s connector panel. Seating may

require thumb pressure on the top and bottom of the card’s front panel.

CAUTION: Take care not to press on any of the LEDs.

2. Tighten the two thumb screws on the card until the front panel of the card is seated against the front of the rack.

FVT/FVR801

Installation Considerations

This fiber-optic link is supplied as a

Standalone/Rack module. Units should be

installed in dry locations protected from

extremes of temperature and humidity.

Standalone Module:

The unit is provided with a mounting

plate with holes for two No. 6 pan head

screws (3-mm or 3.55-mm).

Attach the module to a solid piece of

wood using two No. 6 pan head wood

screws with a minimum penetration

into the wood of 3/4 inch. (Screws not

supplied) See figure 1.

1. Determine where the module will

be installed, and ensure that there

is adequate space at both ends for

making the various cable connections

and for reading the diagnostic LEDs.

2. Attach the module to a flat surface

using two mounting screws.

INS_FVT/FVR801_REV–

08/19/09

Page 1

For Technical Support, Contact Your Nearest Communication Networks Office:

3 Corporate Drive • Danbury, CT 06810 • USA • Tel: 203-796-5300 • Toll Free: 1-888-678-9427 • www.comnet.net

8 Turnberry Park Road • Gildersome • Morley • Leeds, UK LS27 7LE • Tel: +44 (0)113 307 6400 • Fax: +44 (0)113 253 7462

.156 [3.96 mm]

INS_FVT/FVR801_REV–

08/19/09

Page 2

INSTALLATION INSTRUCTIONS

WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12 VDC @ 1A.

WARNING: This unit should be installed in a restricted access location; available through the use of a lock and key or other means of security.

Access should be limited to service personnel who have been instructed about the reasons for the restrictions to the location. Any and all pre-

cautions should be taken and controlled by the authority responsible for the location.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environ-

ment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible

with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the

equipment is not compromised.

FVT801

8-CHANNEL 10-BIT DIGITAL VIDEO TRANSMITTER

For Technical Support, Contact Your Nearest Communication Networks Office:

3 Corporate Drive • Danbury, CT 06810 • USA • Tel: 203-796-5300 • Toll Free: 1-888-678-9427 • www.comnet.net

8 Turnberry Park Road • Gildersome • Morley • Leeds, UK LS27 7LE • Tel: +44 (0)113 307 6400 • Fax: +44 (0)113 253 7462

BLACK WITH WHITE STRIPE

BLACK

MULTIMODE OR

SINGLE MODE

OPTICAL FIBER

NOTE: Remove Electrical Connector for Rack Mount Units

INS_FVT/FVR801_REV–

08/19/09

Page 3

INSTALLATION INSTRUCTIONS

WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated 9-12 VDC @ 1A.

WARNING: This unit should be installed in a restricted access location; available through the use of a lock and key or other means of security.

Access should be limited to service personnel who have been instructed about the reasons for the restrictions to the location. Any and all pre-

cautions should be taken and controlled by the authority responsible for the location.

IMPORTANT SAFEGUARDS:

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environ-

ment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible

with the maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the

equipment is not compromised.

FVR801

8-CHANNEL 10-BIT DIGITAL VIDEO RECEIVER

For Technical Support, Contact Your Nearest Communication Networks Office:

3 Corporate Drive • Danbury, CT 06810 • USA • Tel: 203-796-5300 • Toll Free: 1-888-678-9427 • www.comnet.net

8 Turnberry Park Road • Gildersome • Morley • Leeds, UK LS27 7LE • Tel: +44 (0)113 307 6400 • Fax: +44 (0)113 253 7462

MULTIMODE OR

SINGLE MODE

OPTICAL FIBER

BLACK WITH WHITE STRIPE

BLACK

NOTE: Remove Electrical Connector for Rack Mount Units

INS_FVT/FVR801_REV–

08/19/09

Page 4

FVT/FVR801

8-CHANNEL 10-BIT DIGITAL VIDEO

For Technical Support, Contact Your Nearest Communication Networks Office:

3 Corporate Drive • Danbury, CT 06810 • USA • Tel: 203-796-5300 • Toll Free: 1-888-678-9427 • www.comnet.net

8 Turnberry Park Road • Gildersome • Morley • Leeds, UK LS27 7LE • Tel: +44 (0)113 307 6400 • Fax: +44 (0)113 253 7462

LED INDICATORS

LINK VIDEO POWER

GREEN Communication link has An active video signal is Unit powered up

been established over present on the BNC

optical fiber connector.

RED Communication link has No video signal –

not been established.

OFF Not powered up correctly – Unit powered down

Dieses Handbuch passt für folgende Modelle

Andere Comnet Sender Handbücher

Comnet

Comnet FVT10C1(M,S)1/M Series Bedienungsanleitung

Comnet

Comnet FVT80D8SFP Bedienungsanleitung

Comnet

Comnet FVR1031 series Betriebsanleitung

Comnet

Comnet FVR1031S1 Bedienungsanleitung

Comnet

Comnet netwave NWKED Bedienungsanleitung

Comnet

Comnet FVR1021 Series Bedienungsanleitung

Comnet

Comnet FVT1031 Bedienungsanleitung

Comnet

Comnet FDC8ISOT1 Bedienungsanleitung

Comnet

Comnet FVT4014 Bedienungsanleitung

Comnet

Comnet FVTR1D1A2C1M1 Bedienungsanleitung

Comnet

Comnet FVT8014 Bedienungsanleitung

Comnet

Comnet FVT1C1BM1-M Bedienungsanleitung

Comnet

Comnet FVT40SFP Series Bedienungsanleitung

Comnet

Comnet FVT4014SHR Bedienungsanleitung

Comnet

Comnet FVT11MAC Bedienungsanleitung

Comnet

Comnet FVT20 Bedienungsanleitung

Comnet

Comnet FVTR Bedienungsanleitung

Comnet

Comnet FVT80D4SFP Bedienungsanleitung

Comnet

Comnet FVT10 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung