Compaq Presario 6600 - Desktop PC Bedienungsanleitung
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 1 of 100 Printed: 03/06/03 02:02 PM
Installing the Wireless Keyboard and Mouse Set
Installation de l’ensemble clavier/souris sans fil
Instalación del set de teclado y ratón inalámbricos
Installazione della tastiera e del mouse senza fili
De draadloze muis- en toetsenbordset installeren
Installere settet med trådløst tastatur og trådløs mus
Installera det trådlösa tangentbordet och den trådlösa musen
Installieren des kabellosen Tastatur/Maus-Sets
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 2 of 100 Printed: 03/06/03 02:02 PM
Installing the Wireless Keyboard and Mouse Set 1
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 1 of 100 Printed: 03/06/03 02:02 PM
English
Installing the Wireless
Keyboard and Mouse Set
The wireless keyboard and mouse set consists
of a receiver (D) that plugs into the computer,
a wireless keyboard (K) and a wireless
mouse (M).
Note: This wireless set is compatible with
your model PC and not intended
for use with other computers.
D
K
M
Note: You can replace the batteries in the mouse
and keyboard without turning off the
computer. The computer must be on to
change the ID setting on the three units.
2Installing the Wireless Keyboard and Mouse Set
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 2 of 100 Printed: 03/06/03 02:02 PM
Getting the Mouse Ready
M2 M1
M3
Note: Do not use rechargeable batteries
in the mouse. Alkaline batteries are
recommended.
Install the two AA alkaline batteries (provided)
in the wireless mouse:
1 Push in at M1, and lift the battery cover (M2)
from the bottom of the mouse.
2 Insert the batteries into the compartment.
Note the battery images on the inside of the
compartment, and make sure batteries are
placed in the correct direction.
3 Replace the cover.
Note: The red light (M3) turns on when the
batteries are installed correctly.
Installing the Wireless Keyboard and Mouse Set 3
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 3 of 100 Printed: 03/06/03 02:02 PM
English
Getting the Keyboard Ready
K1 K3
K3 K2
K
Note: Do not use rechargeable batteries in
the keyboard. Alkaline batteries are
recommended.
Install the two AA alkaline batteries (provided) in
the wireless keyboard:
1 Place the keyboard (K) upside down with the
battery compartment (K2) away from you, as
shown in the illustration.
2 Remove the cover (K1) from the bottom of the
keyboard.
3 Insert a battery into the compartment (K2),
and slide the battery to the right. Insert the
second battery. Note the battery images on the
inside of the compartment, and make sure
batteries are placed in the correct direction.
4 Replace the cover.
5 Adjust the keyboard height by lifting the
adjustment legs (K3).
4Installing the Wireless Keyboard and Mouse Set
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 4 of 100 Printed: 03/06/03 02:02 PM
Getting the Receiver Ready
The receiver (D) must be placed flat on a surface,
and positioned properly to avoid interference
from other electrical equipment.
1 Turn off your computer.
2 Connect the receiver cable (D1) to a USB
connector on the front or the back of the
computer.
D1
D
3 Set the receiver flat on a surface, and follow
these guidelines:
■ A: Minimum 20 cm (8 inches) clearance
between the receiver and other electronic
devices.
■ B: Maximum 1.5 m (59 inches) distance
between the receiver and wireless mouse or
wireless keyboard.
Installing the Wireless Keyboard and Mouse Set 5
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 5 of 100 Printed: 03/06/03 02:02 PM
English
■ C: Minimum 20 cm (8 inches) clearance between the receiver and the monitor.
■ Place no electronic device between the receiver and wireless mouse or wireless keyboard.
A
B
B
C
Note: This is one example of the setup. Other setup positions are also possible.
Warning: To avoid causing interference, keep the receiver at least 20 cm (8 inches) away from
the monitor.
6Installing the Wireless Keyboard and Mouse Set
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 6 of 100 Printed: 03/06/03 02:02 PM
Setting Up the Wireless Set
The mouse and keyboard have 255 IDs that are
randomly selected when you press the ID button.
This helps protect against interference from other
wireless devices in the same area.
Important: The word CONNECT is the label for
the ID button on the bottom of the mouse
and keyboard. To press the ID button, use
a blunt pointed object, like the tip of a
ballpoint pen.
Important: Whenever you want to set the IDs of
both the keyboard and the mouse, you must
first set the receiver ID and mouse ID, and
then set the receiver ID and keyboard ID,
as described in this procedure.
1 Turn on the computer.
Important: If the ID button is pressed more than
one time during the setup, you must start
over with step 2.
2 On the front of the receiver (D), press the
ID button (E) once.
The blue activity light (J) on the receiver starts
flashing, and continues flashing until the next
step is completed, or until 30 seconds pass.
E
D
F
G
H
J
Important: If 30 seconds pass before you
complete step 3, you must repeat steps
2 and 3 to set the mouse ID. If the ID button
is pressed more than one time during the
mouse setup (step 3), you must start over
with step 2 and set the receiver ID.
Installing the Wireless Keyboard and Mouse Set 7
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: JimL
Revision #: 105 Page: 7 of 100 Printed: 03/06/03 02:30 PM
English
3 On the bottom of the mouse, press the
ID button (N) once with a blunt pointed object.
The mouse sends a new ID, and flashes the
mouse sensor light (M3) three times. The
receiver flashes the blue activity light (J) three
times and then stops to show it has accepted
the new ID for the mouse.
N
M3
Note: At this time, when you move the mouse
across a surface, the blue activity light (J)
on the receiver will go on and off indicating
the mouse and the receiver are working
together.
Important: The mouse goes into a sleep or
suspend mode after 20 minutes of inactivity.
Click a button on the mouse to wake it.
(Moving the mouse does not wake it.)
4 On the front of the receiver, press the ID button
(E) once.
The activity light (J) on the receiver starts
flashing, and continues flashing until the next
step is completed or until, 30 seconds pass.
E
D
F
G
H
J
Important: If 30 seconds pass before you
complete step 5, you must repeat steps
4 and 5 to set the keyboard ID. If the ID
button is pressed more than one time during
the keyboard setup (step 5), you must start
over with step 4 and set the receiver ID.
8Installing the Wireless Keyboard and Mouse Set
Filename: s3adwlpEU.doc Title: HP-Print2k.dot
Template: HP-Print2K.dot Author: kimt Last Saved By: kimt
Revision #: 103 Page: 8 of 100 Printed: 03/06/03 02:02 PM
5 On the bottom of the keyboard, press the
ID button (L) once with a blunt pointed object.
The keyboard sends a new ID, and the blue
activity light (J) on the receiver flashes three
times, and then stops to show it has accepted
the new ID for the keyboard.
L
K
Note: At this time, when you press a key on the
keyboard or adjust the keyboard volume
knob, the blue activity light (J) on the
receiver goes on and off indicating the
keyboard and the receiver are working
together.
Note: After the receiver, mouse, and keyboard
are working, you can separately reset the
ID button for the mouse (N) or the keyboard
(L) after pressing the receiver ID button (E).
Resetting ID Buttons When
Replacing Batteries
When the batteries are replaced in the mouse or
the keyboard, reset the ID buttons on the receiver
and the unit. You must press the receiver ID
button first, and then press the mouse or the
keyboard ID button. Refer to the steps in the
section “Setting Up the Wireless Set.”
Note: You can replace the batteries in the mouse
and keyboard without turning off the
computer. The computer must be on when
you change the ID setting on the three units.
Andere Handbücher für Presario 6600 - Desktop PC
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Sprachen:
Andere Compaq Computerzubehör Handbücher
