Compex SPE1016E8 Bedienungsanleitung

Quick Install Guide

16-Port 10/100Mbps Ethernet Web Smart Switch

with 8-Port PoE

SPE1016E8

Contents

1: Introduction ..................................................................................1

Features................................................................................................... 1

Packaging Content............................................................................... 2

2: Let’s Get Going-Hardware Setup ...............................................3

Installation ............................................................................................... 3

Rack Mounting......................................................................................... 4

Connecting Network Cable...................................................................... 5

AC Power................................................................................................. 5

3: Accessing to web-based interface ...........................................6

4: Panel Views and Descriptions.....................................................8

Front Panel............................................................................................... 8

Rear Panel ............................................................................................... 9

5: Technical Specifications ...........................................................10

Warranty Registration Card..............................................................26

1: Introduction

This chapter describes the features of the 16-Port 10/100Mbps Ethernet Web

Smart Switch with 8-Port PoE.

Features

 16×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with 8-port PoE

function (port-1 ~ port-8)

 Compliant with IEEE 802.3af specification

 Supports PoE power maximum 15.4W for each PoE ports

 Supports PoE Powered Device (PD) classification identify

 Each port supports auto MDI/MDIX, so there is no need to use cross-over

cables or an up-link port

 Full/half duplex transfer mode for each port

 Wire speed reception and transmission

 Store-and-Forward switching scheme capability to support rate adaptation

and ensure data integrity

 Up to 4K unicast addresses entities per device, self-learning, and table

aging

 512KBytes packet buffer

 Supports IEEE 802.3x flow control for full-duplex mode ports

 Supports Back-pressure flow control for half-duplex mode ports

 Supports 802.1Q VLAN

 Supports Port based QoS and IEEE 802.1p based QoS

 Supports Port based Trunking

 Supports Port-mirroring

 Supports Port-setting for Speed/Disable, Flow control

 Support Port based bandwidth rate control (Ingress rate and Egress rate)

 Easy configuration via WEB Browser

 Easy setting via Web Management Utility

 Standard 19” Rack-mount size

Packaging Content

Open the shipping cartons of the Switch and carefully unpacks its contents.

The carton should contain the following items:

 One 16-Port 10/100Mbps Ethernet Web Smart Switch with 8-Port PoE

 One AC power cord, suitable for your area’s electrical power

connections

 Four rubber feet to be used for shock cushioning

 Screws and two mounting brackets

 CD-Rom with Web Management Utility and User’s Guide

If any item is found missing or damaged, please contact your local reseller for

replacement.

2: Let’s Get Going-Hardware Setup

This chapter provides installation information for the Switch.

Installation

The site where you install the hub stack may greatly affect its performance.

When installing, consider the following pointers:

Install the Switch in a fairly cool and dry place. See Technical Specifications for

the acceptable temperature and humidity operating ranges.

Install the Switch in a site free from strong electromagnetic field generators

(such as motors), vibration, dust, and direct exposure to sunlight.

Leave at least 10cm of space at the front and rear of the hub for ventilation.

Install the Switch on a sturdy, level surface that can support its weight, or in an

EIA standard-size equipment rack. For information on rack installation, see the

next section, Rack Mounting.

When installing the Switch on a level surface, attach the rubber feet to the

bottom of each device. The rubber feet cushion the hub and protect the hub

case from scratching.

Rack Mounting

The switch can be mounted in an EIA standard-size, 19-inch rack, which can be

placed in a wiring closet with other equipment. Attach the mounting brackets

at the switch’s front panel (one on each side), and secure them with the

provided screws.

Figure 1. Combine the Switch with the provided screws

Then, use screws provided with the equipment rack to mount each switch in

the rack.

Figure 2. Mount the Switch in the rack

Connecting Network Cable

The Switch support 16 10/100M Ethernet ports and Port 1 ~ port 8 are PoE Enable

ports, these PoE port will automatically activated when a compatible terminal is

identified, the Switch will supply power through the Ethernet port to the

connected PoE device.

For the Legacy devices that are not yet compatible, the PoE port will not offer

the power to this device. This feature allows users to freely and safely mix

legacy and Power over LAN compatible devices on their network.

The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and it runs both

in half and full duplex mode using two pair of Category 5 cable.

These RJ45 ports are Auto-MDI type port. The Switch can auto transform to MDI-

II or MDI-X type, so you can just make an easy connection that without worrying

if you are using a standard or crossover RJ45 cable.

AC Power

The Switch used the AC power supply 100-240V AC, 50-60 Hz. The power switch

is located at the rear of the unit adjacent to the AC power connector and the

system fan. The switch’s power supply will adjust to the local power source

automatically and may be turned on without having any or all LAN segment ca

3: Accessing to web-based interface

Before you configure this device, note that when the Web Smart Switch is

configured through an Ethernet connection, make sure the manager PC must

be set on same the IP network. For example, when the default network address

of the default IP address of the Web Smart Switch is 192.168.0.1, then the

manager PC should be set at 192.168.0.x (where x is a number between 2 and

254), and the default subnet mask is 255.255.255.0.

Open Internet Explorer 5.0 or above Web browser.

Enter IP address http://192.168.0.1 (the factory-default IP address setting) to the

address location.

Figure 12.

Or through the Web Management Utility, you do not need to remember the IP

Address, select the device shown in the Monitor List of the Web Management

Utility to settle the device on the Web Browser.

When the following dialog page appears, remain enter the default password

"admin" and press Login to enter the main configuration window.

Figure 13.

After entering the password, the main page comes up, the screen will display

the device status.

Figure 14. Device Status

4: Panel Views and Descriptions

This chapter describes the front panel, rear panel, and LED indicators of the

Switch.

Front Panel

The figure below shows the front panels of the Switch.

Figure 3. Front panel of 16-port Gigabit Ethernet Switch with 8-port PoE

LED Indicator:

Comprehensive LED indicators display the status of the switch and the network

(see the LED Indicators chapter in User Manual).

PoE Ports (Port 1~8):

These ports are PoE Enable ports, the PoE port will automatically activated

when a compatible terminal is identified, the Switch will supply power through

the Ethernet port to the connected PoE device.

For the Legacy devices that are not yet compatible, the PoE port will not offer

the power to this device. This feature allows users to freely and safely mix

legacy and Power over LAN compatible devices on their network.

These ports support network speeds of either 10Mbps or 100Mbps, and can

operate in half- and full- duplex transfer modes. These ports also supports

automatic MDI/MDIX crossover detection function gives true “plug and play”

capability, just need to plug-in the network cable to the hub directly and don’t

care if the end node is NIC (Network Interface Card) or switch and hub.

Inhaltsverzeichnis

Andere Compex Netzwerk-Router Handbücher

Compex

Compex readylink CGX3224 Bedienungsanleitung

Compex

Compex SDS1224 Bedienungsanleitung

Compex

Compex ReadyLINK PS2208B-SS Bedienungsanleitung

Compex

Compex PS2216 1D Bedienungsanleitung

Compex

Compex SAS2224B Bedienungsanleitung

Compex

Compex NETPASSAGE NP25G Bedienungsanleitung

Compex

Compex NetPassage 15-C Bedienungsanleitung

Compex

Compex DSR2216 Bedienungsanleitung

Compex

Compex SDS1224 2a Bedienungsanleitung

Compex

Compex GSC2024WM 1A Bedienungsanleitung

Compex

Compex MRL21E Bedienungsanleitung

Compex

Compex READYLINK SDS1224 Bedienungsanleitung

Compex

Compex DSG1008 Bedienungsanleitung

Compex

Compex ReadyLink 8 Port 10/100/1000Mbps Ethernet Switch... Bedienungsanleitung

Compex

Compex GigaSwitch gsc2008wm Bedienungsanleitung

Compex

Compex NetPassage 18A Bedienungsanleitung

Compex

Compex GSM8308 Bedienungsanleitung

Compex

Compex NetPassage 18A Bedienungsanleitung

Compex

Compex ReadyLink PS2208B Bedienungsanleitung

Compex

Compex MicroHub /6 TP1006C Bedienungsanleitung

Compex

Compex PASSAGE Bedienungsanleitung

Compex

Compex Pocket Switch PS2216 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise