Component Playgrounds PH45 Bedienungsanleitung
NAME: __________________________________
INV #: __________________________________
DATE: ___________________________________
BOX PULLED BY: __________________________
STAGED BY: ______________________________
SHIPPING PIECES: 24
WEIGHT: 721 lbs
MODEL PH45
_____ 1 - 11’7” top rail, one drill
_____ 1 - triple end with socket
_____ 1 - 4’ x 4’ Deck package
_____ 4 - 9’ 6” Playhouse legs
_____ 1- 5’6” Top rail with insert
_____ 1 - Side Barriers
_____ 1 - Entrance Barrier
_____ 2 - Exit Barrier
_____ 2 - 8’ 4 rung ladder with adj. sleeves
_____ 1 - 12’6” horizontal ladder
_____ 2 - 8’ A-frame legs
_____ 1 - 5’6” x 2⅜” top rail
_____ 1 - 10’ Plastic Rail Slide __________
_____ 2 - PH Canopy Arches
_____ 1 - CH/PH Wild Climber
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
_____ 4 - 5” swing seats _________________
_____ 1 - trapeze bar _________________
_____ 10 -2 ⅜” Brass Bushing Hangers
_____ 2 - 3½’ chains _________________
_____ 8 - 5½’ chains _________________
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
_____ 1 - Steering wheel _____________
_____ 1 - Steering wheel hardware pkg
_____ 1 - Telescope _______________
_____ 1 - Telescope hardware pkg
_____ 1 - PH Canopy Tarp _________________
■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
_____ 1- HL Bolt Pack
_____ 1 -MT Bolt Pack
_____ 1 - Playhouse bolt pack
_____ 1 - Spring Clip 16 Pack
_____ 2 - 1⅜” Plugs
_____ 4 - Panel Clamps (2 pair)
_____ 2 - ⅜” x 2” Carriage Bolts
_____ 2 - ⅜” Hex Nuts
_____ 4 - Spring Clips
_____ 2 - ⅜” nyloc nuts
_____ 4 - ⅜” x ⅜” set screws
_____ 2 - 2 ⅜” plastic plugs
_____ 1 - Can of ____________ touch up paint
_____ 1 - Set of Instructions
Last Modied: 6/1/2009
Pipe Clamp
Clevis with Key
SwingSetPartsIdentificationPage
The Small Parts
LocWasher
Flat Washer CarriageBolt
HexBolt
TapBolt
SetScrewwith
AllenWrench
NylocNut
HexNut
T-Nut GrabberScrew
LagScrew
#14SheetMetalScrew
#14TrussScrew
Plug Panel Clamp
BraceBand Carabineer/
Spring Clip
Noteverymodelwillhaveeverycomponentorswingpart.Picturesarenottoscale.Thepurposeofthissheetis
togiveyouageneralideaoftheshapeandnamesofthepartsofyourswingset.
©2008 Swings & Things Inc.
BoltLength
:?
12?
2?
22?
2:?
3?
32?
23?
3:?
4?
42?
EXAMPLE
InstallationInstructions
PH45
Wheelbarrow
Shovel
Digging Bar or Pick
Allen Wrench (provided)
Hammer or Mallet
Marker Pen
Ladder
Tape Measure
Level
Open end or box wrench’s:
5/8”, 9/16”, 3/4”, 1/2”
Ratchet Handle & Sockets:
5/8”, 9/16”, 3/4”, 1/2”
Cordless or electric drill w/bits as Follows:
Phillips, 3/8” drill bit
1. Select an area in your yard that is reasonably level and meets the space requirements for your equipment. Ground
space: 17’ x 32’. Play space: 21’ x 41’.
2. Please refer to the outrigger assembly sheet and assemble your outrigger as instructed.
3. Position the horizontal ladder in your yard where you want the unit to nally stand. Measure and be certain that all
necessary clearances for the deck and swinging space are available in this position.
4. Using a tape measure and marker, mark location of the Ladder and swing hangers along the 5’ top rail. See the detail
on the front page of your installation instructions. Set aside.
5. With the horizontal ladder in position on the ground, locate and mark the holes for the two upright ladders. Move
the horizontal ladder out of the way and dig the holes for the upright ladders. (See #1: Hole size for upright ladder)
6. Lay each vertical ladder on the ground near the hole where it will eventually stand. Make a mark 15” from the top
of the ladder onto each ladder rail. Move the adjustable sleeves to these marks and position them to receive the hori-
zontal ladder by turning them to point at a 90 degree angle (towards what will become the inside of the structure)
away from the upright ladder. Secure the set screws.
7. Place the 8’ vertical ladder that will be used to access the Playhouse deck into its hole. The ladder rungs should be
positioned to allow for access into the Playhouse.
8. Place the outrigger out of your way and about 10’ away from where the unit will nally stand.
9. Using a tape measure and marker, mark the locations on the outrigger for the swing hangers and the ladder.
10. Assemble swing hangers as shown on the swing hanger assembly sheet and attach to the out rigger as instructed.
(Hint: Do not attach the swing hangers at the end of the out rigger until after it is inserted into the ladder top sleeve).
11. Turn the outrigger upside down on the ground. Install the legs into the triple end as shown in: #3 A-Frame Leg As-
sembly.
12. Lay the vertical ladder onto the ground with the bottom of the ladder just over the hole where it will eventually stand.
13. Slide the out rigger into the ladder top sleeve. Using two strong adults, stand the unit up and allow the ladder to fall
into the hole previously dug. Check to make sure that the outrigger is still in its proper place inside the ladder top
sleeve. Adjust as necessary by holding onto the ladder securely and pushing or pulling the “A” frame section caus-
ing the outrigger to slide inside the top sleeve of the ladder. When you are satised that the outrigger is in its proper
position, securely tighten the set screws in the top sleeve of the ladder. The unit will not be level at this point. Adjust
and straighten the unit in the play space as desired.
14. Mark the holes for the A-frame legs. Hint: Keep most of the hole to the inside of the leg.
15. Dig the holes and place the legs in the holes.
16. Using two strong adults, lift the horizontal ladder and slide it onto the adjustable sleeves of the ladder that is away
from the Playhouse end of the structure. Secure the set screws.
17. Bring the other vertical ladder up to the horizontal ladder and insert the adjustable sleeves as before. Secure the set
screws. See #4 horizontal ladder connection to upright ladder. Hint: Do not push the overhead ladder tight against
the vertical ladders. Leave a ½” to 1” gap between the vertical ladder rails and the overhead ladder. This will allow
for easier adjustment of the overhead ladder in the future.
18. Insert the 5’ top rail into the top sleeve of the vertical ladder that will be used to access the Playhouse deck.
19. Refer to: Playhouse Assembly and Installation Instructions. Assemble the Playhouse deck and structure, and position
the deck as shown.
20. Attach the slide as shown on the slide assembly sheet.
21. Attach any additional climbers as may be necessary.
22. Using a hammer, install the 2-3/8” plugs into the open ends of the top rails.
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING
*Beforedigging,Pleaseobeylocallawsbynotifyingyourlocalutilitiesmarkingorganization*
RequiredTools
23. Measure the height of the top rail to insure proper swing height.
24. Check the level of the entire structure and adjust as necessary.
25. When you are satised that the structure is level, mix and pour the concrete according to the package directions. You
will use approximately seven 80# bags in the ladder hole and 1 ½ bags in each of the leg holes.
26. Allow the concrete to cure completely before using your swing set. (3-5 days).
27. Attach chains and swinging items and enjoy your Component Playground.
OUTRIGGER ASSEMBLY
Step 1: Slide the end of the drilled Top Rail into the Sleeve of the
Triple End.
Step 2: Align the hole in the Top Rail with hole in the Sleeve of the
Triple End and join together using a 7/16” x 3 1/2” Hex Bolt and
7/16” Nyloc Nut.
Step 3: Insert and tighten (4) 3/8” x 3/8” set screws into the Triple
End Sleeve using Allen Wrench provided.
GROUND SPACE 18’ X 32’
RESIDENTIAL
PLAY SPACE 22’ X 41’
ModelPH45
ModelPH45Continued
Holes 18” x 12”
(approx. 1½ 80 lb. bags
concrete mix per hole)
(C) PH
Legs
3/8” x 2 3/4”
Hex Bolt with
3/8” Nyloc Nut
(1 each per leg)
3/8” x 3/8”
Set Screw
(1 each per leg)
Slide in Leg, bolt in
place and secure
with set screw
#2 A-Frame Leg Assembly
Ladder
Top Rail
Slide Ladder in
place on Top Rail
and secure with
two 3/8” x 3/8”
set screws.
#3LaddertoTopRailAssembly
Set Screw
Top Rail
Upright Ladder
Adjustable Sleeve
Horizontal Ladder
Set
Screws
Set Screws
#4HorizontalLaddertoUprightLadderAssembly
#1HoleSizesforCementingintheSet
28”
24”
20”
Hole 28”x20”x24”
(approximately 7 80 lb. bags
of concrete mix per hole)
(A) Upright
Ladder
DO NOT USE POSTMIX USE GOOD QUALITY CONCRETE MIX!
Triple End
A-Frame
Leg
Holes 18” x 12”
(approx. 1½ 80 lb. bags
concrete mix per hole)
(B) A-Frame
Legs
Hole 12” x 12”
(approx. one 80 lb. bag
concrete mix per hole)
(D) Wild
Climber
©January 1, 2010 Swings & Things Inc.
5’ Playhouse Assembly and Installation Instructions
1.Assemble the platform.
a. Mark the support plates as shown in Side View.
b. Drill 3/8” pilot holes at each mark.
c. Assemble des supports as shown in Deck Support View.
d. Attach boards A and B fi rst. Evenly space the remaining boards (about ¾” apart) and attach to the support plates using
the 2 ½” grabber screw. Refer to Top View.
e. The platform should just square its self up as it is assembled. However, you should verify that the platform is square
before continuing on with the assembly.
e1. How to determine if your platform is square: Use a tape measure. Determine the diagonal corner to corner measure-
ment. Verify that measurement with the opposite diagonal corner to corner measurement. Within a small margin of error,
these two measurements should be the same.
Inhaltsverzeichnis
Andere Component Playgrounds Spielgeräte und Spielplatzausstattung Handbücher
Component Playgrounds
Component Playgrounds Super Swing w/ Slide Bedienungsanleitung
Component Playgrounds
Component Playgrounds HL55 Bedienungsanleitung
Component Playgrounds
Component Playgrounds CH35 Bedienungsanleitung
Component Playgrounds
Component Playgrounds PH52 Bedienungsanleitung
Component Playgrounds
Component Playgrounds HL50 Bedienungsanleitung
Component Playgrounds
Component Playgrounds MT40 Bedienungsanleitung
Component Playgrounds
Component Playgrounds Swing Set PH35-10 Bedienungsanleitung
Component Playgrounds
Component Playgrounds PH35-10 Bedienungsanleitung
Component Playgrounds
Component Playgrounds AR40-10 Bedienungsanleitung
Component Playgrounds
Component Playgrounds ST30 Bedienungsanleitung
Component Playgrounds
Component Playgrounds AR20 Bedienungsanleitung
Component Playgrounds
Component Playgrounds Super Swing w/ Slide and Buoy Ball Bedienungsanleitung
Component Playgrounds
Component Playgrounds ST20 Bedienungsanleitung
Component Playgrounds
Component Playgrounds CP-PS36-8 Bedienungsanleitung
Component Playgrounds
Component Playgrounds SS47-10 Bedienungsanleitung
Component Playgrounds
Component Playgrounds SS38-10 Bedienungsanleitung
Component Playgrounds
Component Playgrounds HL50-10 Bedienungsanleitung
Component Playgrounds
Component Playgrounds AR20-10 Bedienungsanleitung
Component Playgrounds
Component Playgrounds Super Swing w/ Tire Bedienungsanleitung
Component Playgrounds
Component Playgrounds A-Frame Junior Bedienungsanleitung
Beliebte Spielgeräte und Spielplatzausstattung Handbücher anderer Marken
Ledon
Ledon 302040 Bedienungsanleitung
FUNormous
FUNormous Disney Junior MICKEY MOUSE Bedienungsanleitung
b4Adventure
b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Bedienungsanleitung
PoolMaster
PoolMaster 72775 Bedienungsanleitung
Palmako
Palmako 4743142009857 Installationshandbuch
BOERPLAY
BOERPLAY PSTE000.019 Bedienungsanleitung
