Comtech EF Data Digicast CMR-6000 Bedienungsanleitung

CMR-6000

Quick Start Guide

CMR-6000 Digicast Media Router

Part Number MN-CMR6000-QSG REV. 1

Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA, (480) 333-2200, FAX: (480) 333-2161.

MN-CMR6000-QSG

Quick Start Guide

CMR-6000 Digicast Media Router

Contact the Comtech EF Data Customer Support Department for:

•Product support or training

•Reporting comments or suggestions concerning manuals

•Information on upgrading or returning a product

A Customer Support representative may be reached at:

Comtech EF Data

Attention: Customer Support Department

2114 West 7th Street

Tempe, Arizona 85281 USA

480.333.2200 (Main Comtech EF Data Number)

480.333.4357 (Customer Support Desk)

480.333.2161 FAX

To return a Comtech EF Data product (in-warranty and out-of-warranty) for repair or

replacement:

•Contact the Comtech EF Data Customer Support Department. Be prepared to supply the

Customer Support representative with the model number, serial number, and a description

of the problem.

•Request a Return Material Authorization (RMA) number from the Comtech EF Data

Customer Support representative.

•Pack the product in its original shipping carton/packaging to ensure that the product is not

damaged during shipping.

•Ship the product back to Comtech EF Data (Shipping charges should be prepaid).

For Online Customer Support:

An RMA number request can be requested electronically by contacting the Customer Support

Department at www.comtechefdata.com/service.asp:

•Click on the “RMA Request Form” hyperlink, then fill out the form completely before

sending.

•Send e-mail to the Customer Support Department at [email protected] .

For information regarding this product’s warranty policy, refer to the Warranty Policy.

IMPORTANT NOTE: The information contained in this document supersedes all

previously published information regarding this product. Product specifications are

subject to change without prior notice.

Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA.

MN-CMR6000-QSG REV 1

Major Assembly

The Comtech EF Data Digicast Media Router CMR-6000 is available in a standalone configuration. The

following table lists the components provided with a standard configuration. In the event any listed item

is missing, please contact Comtech EF Data Customer Support.

Quantity Description

1 CMR-6000 [CMR-6000]

1 IEC Power Cable

1 CA-TERMINAL Terminal Cable

1 Quick Start sheet

Installation

The CMR-6000 is designed for ease of installation and configuration. Once the unit has been removed

from the packing container, please follow these instructions:

Step Procedure

1 Place the unit on a flat surface with free airflow, where the LEDs can be clearly observed

and with unrestricted access to the rear panel of the unit.

2 Until the unit has been fully configured, the coaxial connection to the Low Noise Block

(LNB) should NOT be connected to the unit. If the unit will not be powering the LNB, it is

recommended that 'Polarity' (on the 'Tuner' configuration page) be set to 'Off'.

3 Connect the power cable to the back of the unit.

4 Connect an RJ-45 Ethernet cable (patch cord) to the port labeled ETHERNET and to an

Ethernet concentrator (hub) or switch.

5 Connect a terminal cable P/N CA-TERMINAL (supplied) to the port labeled TERM and to

a PC’s serial port (DB-9), to initially configure the CMR-6000.

6 Connect the AC power cord to a standard wall outlet and the unit.

7 Upon startup, the LEDs on the front panel may illuminate as follows:

Colo

Label Description

Green/Red STATUS Red indicates error status, green indicates status ok

Green LOCK Solid green indicates the tuner is locked

Green E-LINK LED illuminates if the Ethernet connection to the Hub/Switch

is operational

Green REDUN Redundancy indicator. Solid green unit is redundant online

and flashing green is redundant offline (backup)

Amber ASI-TX Solid when ASI is enabled

Amber ASI-RX Solid when ASI input is connected

Ambe

E-ACT Flashes when there is Ethernet activity

Solid when management connection (web or Telnet)

Amber MGT

Initial Configuration

The initial configuration requires setting up the IP parameters via the terminal cable. Once the IP

parameters have been configured, the terminal cable can be removed. Store the terminal cable in a known

location, because it may be needed in the future. The front panel may also be used for initial configuration

of the IP parameters.

Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA.

MN-CMR6000-QSG REV 1

Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA.

To configure the IP parameters via the terminal cable:

Step Procedure

1 Using a terminal emulator on a PC such as HyperTerminal™ or TeraTerm™, set up the

communication port as follows:

• 38,400 BAUD

• 8 Data Bits

• 1 Stop Bit

• No Parity

• No Flow Control

2 Press the <ENTER> key on the PC – the login prompt should be displayed.

3 The default user is comtech and the default password is comtech. After logging in, the CMR-

6000’s menu should be displayed.

4 Press “N” for Network Menu.

5 Press “I” for the IP Address, Enter the IP Address and press <ENTER>.

6 Press “M” for the Subnet Mask. Enter the Subnet Mask and press <ENTER>.

7 Press “G” for the Default Gateway IP Address. Enter the Default Gateway Address and press

<ENTER>.

8 Press “S” to save the parameters.

9 Press “Y” to confirm the saving of parameters.

10 Press “X” to exit to the main menu.

To configure the IP parameters via the front panel:

Step Procedure

1 Use the keypad to navigate the Vacuum Fluorescent Display (VFD) menu display

2 Select the Config menu option

3 Select the Ethernet menu option

4 Select the IP Address option and enter the IP address (in dotted decimal format ) and

subnet mask (in CIDR format)

5 Select Gateway and enter the IP address of the default gateway

6 Select Link and enter the appropriate speed/duplex setting. Auto is the default and

recommended configuration of the LAN interface

After completing the final step in either of these procedures, the unit has been configured for full IP

operation. The tuner settings may also be configured via the front panel, although additional

configuration and management is best performed using the web interface (refer to Chapter 4, Device

Management via User Interfaces, in the installation and operation manual).

Once fully configured, the coaxial connection to the Low Noise Block (LNB) may be safely attached to

the L-Band input port. Read Section 2.5, Connect External Cables, in the installation and operation

manual for more information about the LNB connection.

Download Product Documentation

Full product documentation, including the installation and operation manual, is available for

download from

www.comtechefdata.com/ProductDigicast.asp

MN-CMR6000-QSG REV 1

2114 WEST 7TH STREET TEMPE ARIZONA 85281 USA

480 •333 •2200 PHONE

480 •333 •2161 FAX

Warranty Policy

Comtech EF Data products are warranted against defects in material and workmanship for a period of two years

from the date of shipment. During the warranty period, Comtech EF Data will, at its option, repair or replace

products that prove to be defective.

For equipment under warranty, the owner is responsible for freight to Comtech EF Data and all related customs,

taxes, tariffs, insurance, etc. Comtech EF Data is responsible for the freight charges only for return of the

equipment from the factory to the owner. Comtech EF Data will return the equipment by the same method (i.e.,

Air, Express, Surface) as the equipment was sent to Comtech EF Data.

All equipment returned for warranty repair must have a valid RMA number issued prior to return and be marked

clearly on the return packaging. Comtech EF Data strongly recommends all equipment be returned in its original

packaging.

Comtech EF Data Corporation’s obligations under this warranty are limited to repair or replacement of failed

parts, and the return shipment to the buyer of the repaired or replaced parts.

Limitations of Warranty

The warranty does not apply to any part of a product that has been installed, altered, repaired, or misused in any

way that, in the opinion of Comtech EF Data Corporation, would affect the reliability or detracts from the

performance of any part of the product, or is damaged as the result of use in a way or with equipment that had not

been previously approved by Comtech EF Data Corporation.

The warranty does not apply to any product or parts thereof where the serial number or the serial number of any

of its parts has been altered, defaced, or removed.

The warranty does not cover damage or loss incurred in transportation of the product.

The warranty does not cover replacement or repair necessitated by loss or damage from any cause beyond the

control of Comtech EF Data Corporation, such as lightning or other natural and weather related events or wartime

environments.

The warranty does not cover any labor involved in the removal and or reinstallation of warranted equipment or

parts on site, or any labor required to diagnose the necessity for repair or replacement.

The warranty excludes any responsibility by Comtech EF Data Corporation for incidental or consequential

damages arising from the use of the equipment or products, or for any inability to use them either separate from or

in combination with any other equipment or products.

A fixed charge established for each product will be imposed for all equipment returned for warranty repair where

Comtech EF Data Corporation cannot identify the cause of the reported failure.

Exclusive Remedies

Comtech EF Data Corporation’s warranty, as stated is in lieu of all other warranties, expressed, implied, or

statutory, including those of merchantability and fitness for a particular purpose. The buyer shall pass on to any

purchaser, lessee, or other user of Comtech EF Data Corporation’s products, the aforementioned warranty, and

shall indemnify and hold harmless Comtech EF Data Corporation from any claims or liability of such purchaser,

lessee, or user based upon allegations that the buyer, its agents, or employees have made additional warranties or

representations as to product preference or use.

The remedies provided herein are the buyer’s sole and exclusive remedies. Comtech EF Data shall not be liable

for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any other

legal theory.

Inhaltsverzeichnis

Andere Comtech EF Data Netzwerk-Router Handbücher

Comtech EF Data

Comtech EF Data CMR-5995 Bedienungsanleitung

Comtech EF Data

Comtech EF Data Vipersat 564L Bedienungsanleitung

Comtech EF Data

Comtech EF Data Vipersat CDD-562L Bedienungsanleitung

Comtech EF Data

Comtech EF Data Vipersat SLM-5650A Bedienungsanleitung

Comtech EF Data

Comtech EF Data CDM-800 Bedienungsanleitung

Comtech EF Data

Comtech EF Data CMR-5995 Bedienungsanleitung

Comtech EF Data

Comtech EF Data CDM-840 Bedienungsanleitung

Comtech EF Data

Comtech EF Data Vipersat CDM-570 Bedienungsanleitung

Comtech EF Data

Comtech EF Data Vipersat CDM-570 Bedienungsanleitung

Comtech EF Data

Comtech EF Data CDD-880 Bedienungsanleitung

Comtech EF Data

Comtech EF Data CDD-880 Bedienungsanleitung

Comtech EF Data

Comtech EF Data Vipersat CDM-570 Bedienungsanleitung

Comtech EF Data

Comtech EF Data CMR-5975 Bedienungsanleitung

Comtech EF Data

Comtech EF Data Vipersat CDD-562L Bedienungsanleitung

Comtech EF Data

Comtech EF Data CDM-800 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise