Comtrend Corporation NexusLink 3120 Bedienungsanleitung

For General Information,

Visit Our Website at www.nexicom.net

To Contact Us for Technical Support

and General Inquiries:

On the Phone: 705-775-6394 or 1-888-639-4266

Monday–Friday, 8 am–10 pm,

Saturday 8 am–5 pm, Sunday 9 am–5 pm.

By Email: suppor[email protected]

Through our Knowledge Base: https://kb.nexicom.net

Comtrend NexusLink 3120

High Speed DSL

Setup Guide

More than you expect

Comtrend NexusLink 3120 – Wireless Gateway 3

345

Welcome to Nexicom High Speed DSL

Congratulations, now that you are connected to Nexicom’s High Speed DSL

service you will have the freedom to take full advantage of all the Internet has

to offer. Your DSL connection will change the way you surf. You will now be

exposed to a whole new fast-paced online world.

Nexicom provides you with outstanding customer service and experienced

technicians who are available to answer your questions.

As a Nexicom Internet subscriber you will experience many extended services;

Email Anti-Virus Scanning and Anti-Spam help to protect your computer

system. Nexicom also provides Unlimited Monthly Usage so whether you’re

downloading, uploading or just plain surfing there are no worries about how

much you use.

The Comtrend NexusLink 3120 is a high-quality dual band WiFi router with a

DSL modem built in. Integrated 5 Gigabit Ethernet ports support WLAN 802.11n

2.4GHz and 802.11ac 5GHz frequency bands. The Nexus Link 3120 is designed

for high speed applications and is suitable for triple play services.

NexusLink 3120 has a USB 3.0 host port which provides high speed access for

USB devices such as printer servers, 3G dongle, HDDs, and supports DLNA and

Samba accessibility.

What’s included in the box?

1. Comtrend NexusLink 3120 – Wireless Gateway

2. AC Power Adapter

3. Ethernet Cable

4. Phone Cable

5. Filters

STEP 1

Connecting the Phone Filters

The filters included with your Nexicom High Speed installation kit are to be

used with any type of equipment that utilizes a telephone jack. This includes

telephones, fax machines, answering machines, alarm systems and satellite

receivers. Start by unplugging the phone cable for your existing phone

equipment from the telephone jack and plug it into the end of the filter that

says “PHONE” then plug the short phone cable end of the filter back into the

phone jack.

Note: If you want to plug BOTH your Comtrend NexusLink 3120 and a phone

into the same jack, please use a splitter filter. If you are ONLY plugging your

Comtrend NexusLink 3120 into the jack no filter is needed.

Phone + DSL Splitter Filter

Line: Connect the short phone

cable to this port and connect the

other end to an active wall jack.

Phone: Connect a phone cord

from this port to your phone or

wireless phone’s base unit.

DSL: Connect a phone cord from

this port to the DSL port on your

Comtrend NexusLink 3120.

Comtrend NexusLink 3120 – Wireless Gateway

Comtrend NexusLink 3120 – Wireless Gateway 5

STEP 2

Power ON

Press the Power button to the OFF position (OUT). Connect the power adapter

to the power port. Attach the power adapter to a wall outlet or other AC

source. Press the Power button to the ON position (IN). If the Power LED

displays as expected (Red then Green) then the device is ready for setup.

Caution: If the device fails to power up, or it malfunctions, first verify that

the power cords are connected securely and then power it on again. If the

problem persists, contact the Nexicom Helpdesk at 1-888-639-4266.

4 Ethernet (LAN) Ports

Use 1000-BASE-T RJ-45 cables to connect up to four network devices to a

Gigabit LAN, or 10/100BASE-T RJ-45 cables for standard network usage.

USB Host Port (Type A)

This port can be used to connect the Comtrend NexusLink 3120 to a printer,

or supported USB device.

STEP 3

Connecting Nexicom’s Wireless Gateway

1. Take the grey telephone cable that has come with the kit and plug it

into the grey port on the Comtrend NexusLink 3120 that reads DSL. Next,

connect the other end of the telephone cable into an available telephone

jack. (Note: Do not put a phone filter on the Comtrend NexusLink 3120 and

please use the supplied phone cable. Phone cables longer than 7’ can cause

problems and are not recommended.)

2. Connect the yellow Ethernet cable into the yellow port marked as Ethernet

Port 1 on the back of the Comtrend NexusLink 3120. Next take the other

end of the yellow Ethernet cable and plug it into the Ethernet port on the

back of your computer.

3. Take the black power cable and plug it into the port on the back of the

Comtrend NexusLink 3120 that says Power. Next take the other end of the

power cable and plug it into a power source such as a wall receptacle or

power bar. Press the Power button to the ON position (IN).

4. At this point you should start to see green lights on the front of the

Comtrend NexusLink 3120. Please proceed to the next page. (If you have no

lights, please see FAQ article #6 at the back of manual).

Power On/Off

Toggle Switch

DSL Port Ethernet LAN

Ports (x4)

USB Host Port

Power

Adapter Port

Comtrend NexusLink 3120 – Wireless Gateway 7

STEP 4

Check for DSL Link

When the Comtrend NexusLink 3120 is on and waiting for a connection, focus

on the following 2 lights:

Power: Should be Solid Green.

INTERNET: After about 30 – 90 seconds this light should come on and either

be Solid Green or Blinking Green.

If either of these lights fail to light up green please call the Nexicom Helpdesk

at 1-888-639-4266 for assistance.

If both the Power and the INTERNET light are green you should be able to surf

the Internet if you used a hard-wired connection from one of the 4 Ethernet

LAN ports. If you did not use a hard-wired connection and you wish to set-up

your devices through WiFi please proceed to step 5.

STEP 5

WiFi Set-up

The Comtrend NexusLink 3120 has dual band Wireless capabilities to provide

unprecedented WiFi coverage. The device also has 4 ports marked Eth 1

through Eth 4 for multiple wired connections.

The broadcast SSID name you will look for on your wireless capable devices will

be in the format of the word “Nexicom” then the 4 last digits of the MAC Address

of the Comtrend NexusLink 3120 and either 2.4GHz or 5GHz. It is recommended

to set up both frequencies for any given device, if it is capable, and let the device

choose the best signal depending on your location in the home.

Note: WiFi/WPS buttons are disabled on the 3120 for security reasons.

Your password for the Wireless Network will be on the Comtrend’s label

(located on the bottom of the device) and referred to as the WiFi Key.

To connect your Wireless Smart phone, Tablet or Media device do the following:

1. Navigate to the WiFi settings screen on your smart phone or tablet and

select the SSID (network) for your Comtrend NexusLink 3120, which will be

in the form of NEXICOM- (series of 4 numbers or letters) and either 2.4GHz

or 5GHz.

2. Enter the password into your device from the label on the bottom of your

Comtrend NexusLink 3120 referred to as the WiFi Key. The WiFi Password is

also located on the back of this guide.

3. Be sure to enter capital letters and lowercase appropriately as the

password is case-sensitive.

LED Status Lights

The front panel LED lights are shown below and explained in the following table.

This information can be used to check the status of the device and its connections.

LED Colour Mode Function

POWER

GREEN On The device is powered up.

Off The device is powered down.

RED On

POST (Power On Self Test) failure or other malfunction. A malfunction

is any error of internal sequence or state that will prevent the device

from connecting to the DSLAM or passing customer data.

ETH WAN

GREEN

On WAN is connected at 1000 Mbps.

Off Ethernet WAN is not connected.

Blink In TX/RX over 1000 Mbps.

ORANGE

On Ethernet is connected at 10/100 Mbps.

Off Ethernet WAN is not connected.

Blink In TX/RX over 10/100 Mbps.

ETH 4 to 1

GREEN

On Ethernet is connected at 1000 Mbps.

Off Ethernet is not connected.

Blink In TX/RX over 1000 Mbps.

ORANGE

On Ethernet is connected at 10/100 Mbps.

Off Ethernet is not connected.

Blink In TX/RX over 10/100 Mbps.

WiFi 2.4G GREEN

On The wireless module is ready. (i.e. installed and enabled).

Off The wireless module is not ready. (i.e. either not installed or disabled).

Blink Data transmitting or receiving over WLAN.

WiFi 5G GREEN

On The wireless module is ready. (i.e. installed and enabled).

Off The wireless module is not ready. (i.e. either not installed or disabled).

Blink Data transmitting or receiving over WLAN.

DSL 1 GREEN

On DSL link is established.

Off The device is powered down.

Blink The DSL link is training or some traffic is passing through DSL.

DSL 2 GREEN

On DSL link is established.

Off The device is powered down.

Blink The DSL link is training or some traffic is passing through DSL.

INTERNET

GREEN

IP connected and no traffic detected. If an IP or PPPoE session is

dropped due to an idle timeout, the light will remain green if a DSL

connection is still present.

Off

Modem power off, modem in bridged mode or DSL connection not

present. In addition, if an IP or PPPoE session is dropped for any

reason, other than an idle timeout, the light is turned off.

Blink IP connected and IP traffic is passing through the device (either direction).

RED On

Device attempted to become IP connected and failed (no DHCP

response, no PPPoE response, PPPoE authentication failed, no IP

address from IPCP, etc.)

Comtrend NexusLink 3120 – Wireless Gateway 9

Frequently Asked Questions?

1. What is DSL?

• DSL stands for Digital Subscriber Line. DSL is a high speed Internet access

product for homes and businesses that uses existing copper telephone lines.

2. Can a DSL line be shared among multiple users?

• Yes, multiple computers can be connected through WiFi or by Ethernet cable

using one of the additional yellow ports on the back of the modem. This

is perfect for businesses that need to connect an entire office to one DSL

connection.

3. What are phone filters and what do they do?

• The phone filters are to be placed inline with all the phones in your home

(not on the modem) to prevent the digital signal from interfering with your

telephones as well as preventing the phones from interfering with your

high speed modem. These filters must be inline with all phones in the home

or business for the high speed modem to work correctly.

4. If I move can I take my equipment with me to my new house and have it work?

• Yes, first you must confirm with us if DSL service is available at your new

location. If so, you must inform us to transfer the service as there is

hardware that must be provisioned on the phone line at the new location

for the system to work. There is a charge for this service.

5. Should I have filters on all my phone lines?

• Only on phone jacks that are connected to a phone, fax machine or Audio

Visual equipment. The jack that has a line going into the modem should

NOT have a small single line filter, but you can use the larger DSL splitter

filter using the “DSL” port only for the modem.

6. My Modem has no lights!

• Verify that the power button at the back of the device is in the “ON”

position. Verify that the modem’s power source is plugged into a working

power outlet or power bar. Next, take the modem to another power source

and verify if you get the power light. For further assistance regarding this

error, please call the Nexicom Helpdesk.

7. The filter supplied does not fit with my wall mount phone. What do I do?”

• Don’t worry we have a solution. A wall mount filter can be obtained by

calling Nexicom, we will be happy to make arrangements to provide you

with one of these special filters.

8. What should I do if I change my phone provider?

• Please contact Nexicom prior to making any changes as this will affect

your DSL service and could incur service charges.

9. What should I do if I cannot surf?

• Try turning off the power switch on the back of the Comtrend NexusLink

3120 and wait 30 seconds. Close your browser. Turn the power back on

and wait 4 minutes, open your browser and see if you can surf now.

10. Are the Wireless radios on by Default?

• Yes

11. Is the Wireless Security on by Default?

• Yes, the unit is set up with “WPA2” WiFi security. Login/Password

credentials are printed on the product label affixed to the bottom

of the device.

12. Why is my WiFi signal strength lower than I expected?

• A wireless signal degrades with distance, obstructions and sources of

WiFi noise. Common signal impairments include walls, ceilings, metal,

cinder blocks, fluorescent lights, microwaves, furniture or even a

close neighbour’s WiFi signal. The Comtrend NexusLink 3120 has been

optimized to provide wireless coverage for most situations however it is

best to try to locate it as close to your devices as possible, but this is only

practical if you have one main area where you tend to use your devices.

Otherwise, you should place your router near the center of your home.

Troubleshooting

If your Internet service stops working, do the following:

1. Use the On/Off switch on the back of the Comtrend NexusLink 3120 to turn

OFF the device.

2. Wait for 30 seconds and turn ON the Comtrend NexusLink 3120.

3. Wait for 4 minutes until both the DSL 1 and INTERNET LED lights are GREEN.

4. Test your Internet again.

If you have any questions during or after the setup process, please contact our

friendly Helpdesk staff.

They can be reached by phone at 705-775-6394 or 1-888-639-4266, or by email

at [email protected]. The Helpdesk is available Monday through Friday from

8 am to 10 pm, Saturdays from 8 am to 5 pm and Sundays from 9 am to 5 pm.

Andere Handbücher für NexusLink 3120

Inhaltsverzeichnis

Andere Comtrend Corporation WLAN-Router Handbücher

Comtrend Corporation

Comtrend Corporation CT-535 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-5365 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WR-5881 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WR-6895 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-5361T Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-5365 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation VR-3030 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-5365 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WR-5882 Montage- und Wartungsanleitung

Comtrend Corporation

Comtrend Corporation VR-303 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation Wireless-N Broadband Router Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-535 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-6382T Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation VG-8050 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation AC 1200 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WR-5887 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WAP-5813n Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-5361 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation WR-5882 Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-5372E Bedienungsanleitung

Comtrend Corporation

Comtrend Corporation CT-536+ Bedienungsanleitung

Beliebte WLAN-Router Handbücher anderer Marken

Airlogic

Airlogic AirSync Class 1 Betriebsanleitung

Samsung

Samsung WCH730B Bedienungsanleitung

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Bedienungsanleitung

Askey

Askey RAC2V1K Bedienungsanleitung

Alloy

Alloy WLF2454AP-S Bedienungsanleitung

TELEFONICA

TELEFONICA USB Adapter Bedienungsanleitung

TP-Link

TP-Link TL-WR542G Bedienungsanleitung

Hama

Hama 53120 Bedienungsanleitung

Intellinet

Intellinet 524582 Bedienungsanleitung

Asus

Asus RT-N10P Bedienungsanleitung

D-Link

D-Link DIR-506L Bedienungsanleitung

Sapido

Sapido GR297n Bedienungsanleitung

Asus

Asus DSL-N55U Bedienungsanleitung

AMTC

AMTC WR7502 Bedienungsanleitung

Compaq

Compaq CP-2W - iPAQ Connection Point Bedienungsanleitung

SMC Networks

SMC Networks WBR14-N2 FICHE Bedienungsanleitung

Draytek

Draytek Vigor2120 Series Bedienungsanleitung

Sitecom

Sitecom WLR-4000 Bedienungsanleitung