Comtrol ROCKETLINX ES7110 Bedienungsanleitung
QUICK INSTALLATION GUIDE
2000550 Rev E | Release Date - August 2015
ROCKETLINX ES7110
ES7110/ES7110-VB
INTRODUCTION
The RocketLinx ES7110 series is an industrial Power over Ethernet (PoE)
switch with eight Fast Ethernet ports and two Gigabit uplink ports to ensure
high-bandwidth connecon. The ES7110 is compliant with the IEEE 802.3af
PoE standard to deliver a maximum of 15.4 W per port with a total output
power budget of 65W. The ES7110 series oers the following models:
• ES7110 - with eight Fast Ethernet PoE ports and two RJ45 Gigabit uplink
ports (48VDC)
• ES7110-VB - with eight Fast Ethernet PoE ports and two RJ45 Gigabit
uplink ports (12-24VDC)
To ensure the high quality of video data transmission, the ES7110 not only
provides Gigabit bandwidth uplink for large image trac, but also supports
QoS to adjust the priority of data transfer. Using the Fault Relay, the
ES7110 can automacally warn the administrator if there are any failures.
The compact IP30 rigid aluminum case allows the ES7110 to be reliably
operated in an extreme environment. Refer to the Comtrol website for more
informaon about specic ES7110 model features.
WIRE THE POWER
Use the following procedure to wire the power.
1. Insert the posive and negave wires (12-24AWG) into the PWR+ and
PWR- contacts.
Note: Power should be disconnected from the power supply before connecng it to
the switch. Otherwise, your screwdriver blade can inadvertently short your terminal
connecons to the grounded enclosure.
2. Tighten the wire-clamp screws to prevent the wires from coming loose.
1
WIRE THE ALARM RELAY OUTPUT AND GROUND
The ES7110 provides one alarm relay output. The relay contacts are
energized (open) for normal operaon and close under a faulty condion,
such as an Ethernet port link break. Congure the alarm relay output with
the DIP switches.
1. Insert posive and negave wires into Relay A and Relay B.
2. Tighten the wire-clamp screws to prevent the wires from coming loose.
3. Connect a ground wire between the chassis and earth ground using
12-24AWG wire to ensure that the ES7110 is not damaged by noise or
electrical shock.
a. Loosen the earth ground screw on the boom of the ES7110
with a screw driver.
b. Tighten the screw aer the earth ground wire is connected.
2
Relay PWR
DC Power output Power Supply
AC Power input
12 to 24AWG
Wire
Power Supply Requirements
ES7110 48VDC/96W (Min)
ES7110-VB 12-24VDC/96W (Min)
Electrical Specicaon ES7110 ES7110-VB
Power Input 48VDC 12-24VDC
Power Consumpon (without PD loading) 7W 11W@ 24VDC
Power Consumpon (with PD loading) 75W 80W @ 24VDC
Maximum Output/Power PoE Port 15.4W 15.4W
Total PoE Power Budget 65W 65W
SET THE DIP SWITCH
The ES7110 has a 10-pin DIP switch located on the boom panel to congure
the Port Link Alarm for the Ethernet ports. The following table shows the DIP
switch number mapping to the corresponding
PoE and Gigabit ports as follows.
Port G2 Port G1 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8
DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8 DIP 9 DIP 10
The port break alarm is limited to an auto-negoaon 10/100 full-duplex
device.
3
Maximum 1A/24VDC
Alarm System
Extra Power
System
Port Alarm
Earth Ground
DIP Switch Status Descripon
1 - 2 On Enables the Gigabit port failure alarm for this port
O (Default) Disables the Gigabit port failure alarm for this port
3 - 10 On Enables the PoE port failure alarm for this port
O (Default) Disables the PoE port failure alarm for this port
MOUNT THE ES7110
The ES7110 can be mounted on a DIN rail or on a wall panel. The DIN rail clip
is already aached to the ES7110 at the factory.
Note: The ES7110 will disperse heat through the metal case during PoE port
operaon. The ES7110 should be installed and mounted onto a panel that
provides good heat dispersion.
You can use this procedure to mount the ES7110 on a DIN rail.
1. Insert the upper end of the DIN rail clip into the back of the DIN rail
track from its upper side.
2. Lightly push the boom of the DIN rail clip into the track.
3. Verify that the DIN rail clip is ghtly aached to the track.
CONNECT THE POE OR RJ45 UPLINK PORTS
You can use the following informaon to connect Ethernet cables between
the ES7110 ports and the network nodes.
• Ports G1 and G2 are Gigabit Ethernet ports that support 10BASE-T,
100BASE-TX, and 1000BASE-TX.
• Ports 1-8 are Fast Ethernet 10/100BASE-TX PoE ports that are IEEE
802.3af (PoE) compliant. The Fast Ethernet ports support 10BASE-T and
100BASE-TX, full- or half-duplex modes.
The following table shows the RJ45 pin-out assignments for the PoE and
Gigabit ports.
All ports automacally detect the signal from the connected devices to
negoate the link speed and duplex mode. Auto MDI/MDIX allows you to
connect another switch, hub, or workstaon without changing straight-
through or crossover cables. Crossover cables cross-connect the transmit
lines at each end to the received lines at the opposite end.
4
Connect one side of an Ethernet cable into any switch port and connect the
other side to your aached device. Make sure that the cables are less than
100 meters (328 feet).
• Uplink ports:
10BASE-T: 2-pair
Category 3, 4, 5
cable
• Uplink ports:
100BASE-TX:
2-pair Category 5
• Uplink ports:
1000BASE-TX:
4-pair Category 5
cable
• PoE ports: 4-pair
Category 5e / 6
cable
LEDs
This table provides informaon about the status LEDs.
LEDs Status Descripon
Power Green Valid DC input power applied
O No power
Alarm Red A power link failure has occurred
O No failure has occurred
RJ45 Pin 10/100BASE-TX PoE
(Alternave B)
1000BASE-TX
1RX+ BI_DA+
2 RX - BI_DA-
3 TX + BI_DB+
4 Vport+ BI_DC+
5 Vport+ BI_DC-
6 TX - BI_DB-
7Vport- BI_DD+
8 Vport- BI_DD-
5
This table provides details about the port status LEDs.
Port Status LED Descripon
PoE 1-8
Link/
Acvity
Green The port is connected
Blinking Transming or receiving
packets
O The port link is inacve
PoE 1-8
Full-
Duplex/
Collision
Yellow Full-duplex mode
connecon
Blinking Data collision
O The link is inacve or
operang in half-duplex
mode
G1/G2
Link/
Acvity
Green The port is connected
Blinking Transming or receiving
O The port link is inacve
G1/G2
Speed
Yellow Full-duplex mode
connecon
Blinking 3 blinks per cycle -
1000Mbps
2 blinks per cycle -
100Mbps
1 blink per cycle -
10Mbps
O The link is inacve
6
COMTROL CUSTOMER SERVICE
You can use one of the following methods to contact Comtrol.
Contact Method Web Address or Phone Number
Support hp://www.comtrol.com/support
Downloads hp://downloads.comtrol.com/html/default.htm
Website hp://www.comtrol.com
Phone +1 763.957.6000
7
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Comtrol Netzwerk-Router Handbücher
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise