Comtrol ROCKETLINX ES7105 Bedienungsanleitung
Insert the wires and set the DIP switch using the table below. After setting the DIP
switch to ON, the relay output alarm will detect any power or port failures, and form a
short circuit. The alarm relay output is Normal Open.
Connecting Ethernet Ports
All Ethernet ports support auto MDI/MDIX.
Connect an Ethernet cable into the PoE port of RocketLinx ES7105 switch and the
appropriate network device. The LNK /ACT LED will turn Yellow for 10M Ethernet or
Green for 100M Ethernet. The four PoE ports ( PoE 1 to PoE 4) support PoE OUT. If
the PoE port LED is lit, it indicates that the RJ45 connector has been successfully
connected to a IEEE 802.3af enabled Power Device.
Quick Installation Guide
www.comtrol.com
2000538 Rev C
Comtrol Customer Service
You can contact Comtrol using one of the following methods.
Contact Method Web Address or Phone Number
Support http://www.comtrol.com/pub/en/support
Downloads ftp://ftp.comtrol.com/html/ES7105.htm
Web Site http://www.comtrol.com
Phone 763.957.6000
ROCKETLINX ES7105
Industrial PoE Switch
Introduction Wiring the Power Inputs
Use the following procedure to wire the power inputs. The working voltage is
48VDC or -48VDC.
1. Insert the positive and negative wires into the V+ and V- contact on the terminal
block connector.
2. Tighten the wire-clamp screws to prevent the DC wires from becoming loose.
Wiring the Relay Output
The relay output alarm contacts are in the middle of the terminal block connector.
The RocketLinx ES7105 is an Industrial PoE Power switch that conforms to the IEEE
802.3af Power over Ethernet standard. The RocketLinx ES7105 provides four
10/100BASE-TX PoE ports with one standard 10/100BASE-TX Ethernet port.
For detailed information, refer to the RocketLinx ES7105 User Guide, which is
available on the RocketLinx CD or you can download the latest version.
Package Check List
The following items should be in the product box:
RocketLinx ES7105 Industrial Ethernet PoE Switch
Mounting kit with footpad
Quick Installation Guide
CD-ROM that contains the RocketLinx ES7105 User Guide
Mounting the Unit
If desired, you can use the screws provided in the mounting kit and mount the ES7105
on a wall.
Grounding RocketLinx ES7105 Switch
Connect the frame ground on the switch to an earth ground to ensure safety and to
prevent noise.
PoE Port
1 to 4
Port 5
Fast Ethernet UTP PWR 1
PWR 2
Alarm Relay
1A@DC24V
Earth Ground Screw
W
iri
ng
the Rel
ay
Outpu
t
Wire: 12 to 24 AWG
Power 1 Power 2
-
+-
+
PWR1 PWR2
1A@24V
FAULT
Relay Output Alarm Contacts
1A@24V
-
+-
+
PWR1 PWR2
1A@24V
FAULT
Comtrol Corporation
+1 763.957.6000
www.comtrol.com
Introduction Wiring the Power Inputs
Use the following procedure to wire the power inputs. The working voltage is
48VDC or -48VDC.
1. Insert the positive and negative wires into the V+ and V- contact on the terminal
block connector.
2. Tighten the wire-clamp screws to prevent the DC wires from becoming loose.
Wiring the Relay Output
The relay output alarm contacts are in the middle of the terminal block connector.
The RocketLinx ES7105 is an Industrial PoE Power switch that conforms to the IEEE
802.3af Power over Ethernet standard. The RocketLinx ES7105 provides four
10/100BASE-TX PoE ports with one standard 10/100BASE-TX Ethernet port.
For detailed information, refer to the RocketLinx ES7105 User Guide, which is
available on the RocketLinx CD or you can download the latest version.
Package Check List
The following items should be in the product box:
RocketLinx ES7105 Industrial Ethernet PoE Switch
Mounting kit with footpad
Quick Installation Guide
CD-ROM that contains the RocketLinx ES7105 User Guide
Mounting the Unit
If desired, you can use the screws provided in the mounting kit and mount the ES7105
on a wall.
Grounding RocketLinx ES7105 Switch
Connect the frame ground on the switch to an earth ground to ensure safety and to
prevent noise.
PoE Port
1 to 4
Port 5
Fast Ethernet UTP PWR 1
PWR 2
Alarm Relay
1A@DC24V
Earth Ground Screw
W
iri
ng
the Rel
ay
Outpu
t
Wire: 12 to 24 AWG
Power 1 Power 2
-
+-
+
PWR1 PWR2
1A@24V
FAULT
Relay Output Alarm Contacts
1A@24V
-
+-
+
PWR1 PWR2
1A@24V
FAULT
Comtrol Corporation
+1 763.957.6000
www.comtrol.com
Insert the wires and set the DIP switch using the table below. After setting the DIP
switch to ON, the relay output alarm will detect any power or port failures, and form a
short circuit. The alarm relay output is Normal Open.
Connecting Ethernet Ports
All Ethernet ports support auto MDI/MDIX.
Connect an Ethernet cable into the PoE port of RocketLinx ES7105 switch and the
appropriate network device. The LNK /ACT LED will turn Yellow for 10M Ethernet or
Green for 100M Ethernet. The four PoE ports ( PoE 1 to PoE 4) support PoE OUT. If
the PoE port LED is lit, it indicates that the RJ45 connector has been successfully
connected to a IEEE 802.3af enabled Power Device.
Quick Installation Guide
www.comtrol.com
2000538 Rev C
Comtrol Customer Service
You can contact Comtrol using one of the following methods.
Contact Method Web Address or Phone Number
Support http://www.comtrol.com/pub/en/support
Downloads ftp://ftp.comtrol.com/html/ES7105.htm
Web Site http://www.comtrol.com
Phone 763.957.6000
ROCKETLINX ES7105
Industrial PoE Switch
Insert the wires and set the DIP switch using the table below. After setting the DIP
switch to ON, the relay output alarm will detect any power or port failures, and form a
short circuit. The alarm relay output is Normal Open.
Connecting Ethernet Ports
All Ethernet ports support auto MDI/MDIX.
Connect an Ethernet cable into the PoE port of RocketLinx ES7105 switch and the
appropriate network device. The LNK /ACT LED will turn Yellow for 10M Ethernet or
Green for 100M Ethernet. The four PoE ports ( PoE 1 to PoE 4) support PoE OUT. If
the PoE port LED is lit, it indicates that the RJ45 connector has been successfully
connected to a IEEE 802.3af enabled Power Device.
Quick Installation Guide
www.comtrol.com
2000538 Rev C
Comtrol Customer Service
You can contact Comtrol using one of the following methods.
Contact Method Web Address or Phone Number
Support http://www.comtrol.com/pub/en/support
Downloads ftp://ftp.comtrol.com/html/ES7105.htm
Web Site http://www.comtrol.com
Phone 763.957.6000
ROCKETLINX ES7105
Industrial PoE Switch
Introduction Wiring the Power Inputs
Use the following procedure to wire the power inputs. The working voltage is
48VDC or -48VDC.
1. Insert the positive and negative wires into the V+ and V- contact on the terminal
block connector.
2. Tighten the wire-clamp screws to prevent the DC wires from becoming loose.
Wiring the Relay Output
The relay output alarm contacts are in the middle of the terminal block connector.
The RocketLinx ES7105 is an Industrial PoE Power switch that conforms to the IEEE
802.3af Power over Ethernet standard. The RocketLinx ES7105 provides four
10/100BASE-TX PoE ports with one standard 10/100BASE-TX Ethernet port.
For detailed information, refer to the RocketLinx ES7105 User Guide, which is
available on the RocketLinx CD or you can download the latest version.
Package Check List
The following items should be in the product box:
RocketLinx ES7105 Industrial Ethernet PoE Switch
Mounting kit with footpad
Quick Installation Guide
CD-ROM that contains the RocketLinx ES7105 User Guide
Mounting the Unit
If desired, you can use the screws provided in the mounting kit and mount the ES7105
on a wall.
Grounding RocketLinx ES7105 Switch
Connect the frame ground on the switch to an earth ground to ensure safety and to
prevent noise.
PoE Port
1 to 4
Port 5
Fast Ethernet UTP PWR 1
PWR 2
Alarm Relay
1A@DC24V
Earth Ground Screw
W
iri
ng
the Rel
ay
Outpu
t
Wire: 12 to 24 AWG
Power 1 Power 2
-
+-
+
PWR1 PWR2
1A@24V
FAULT
Relay Output Alarm Contacts
1A@24V
-
+-
+
PWR1 PWR2
1A@24V
FAULT
Comtrol Corporation
+1 763.957.6000
www.comtrol.com
Inhaltsverzeichnis
Andere Comtrol Schalten Handbücher
Comtrol
Comtrol RocketLinx ES8108 Bedienungsanleitung
Comtrol
Comtrol RocketPort Stücklistenhandbuch
Comtrol
Comtrol RocketLinx ES8105 Bedienungsanleitung
Comtrol
Comtrol ROCKET LINX ES7506 Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES8509-XT Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ACS7106 Bedienungsanleitung
Comtrol
Comtrol ROCKET LINX MP1204-XT Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES8510 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES8108 Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES7110-VB Bedienungsanleitung
Comtrol
Comtrol Rocket linx ES8508 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES8520-XT Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES8108 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES7506 Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES7510-XT Bedienungsanleitung
Comtrol
Comtrol RocketPort Bedienerhandbuch
Comtrol
Comtrol RocketLinx ES7528 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES8108 Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES8508 Bedienungsanleitung
Comtrol
Comtrol RocketPort Serial Hub Si Bedienerhandbuch
