Comtrol ROCKETLINX ES7206-XT Bedienungsanleitung
QUICK INSTALLATION GUIDE
2000584 Rev E | Release Date- March 2014
ROCKETLINX ES7206-XT
Industrial PoE Plus Switch
INTRODUCTION
The RocketLinx ES7206-XT is an industrial 6-port Gigabit 802.3af/at PoE
Voltage Boost Switch.
SeetheComtrolwebsiteforproductspecicaons.
INSTALLATION OVERVIEW
YoucanusethefollowinginformaontoinstalltheES7206-XT.TheES7206-XT
istobeconnectedtoPoEnetworkswithoutroungtooutsidetheplant.
Wiring the Power Inputs
TheES7206-XTprovidesredundantpower,reversepolarityprotecon,over-
currentproteconandacceptsaposiveornegavepowersourcebutPWR1
andPWR2mustbeappliedwithpowersourcesofthesamepolarity.
Theterminalblockaccepts12-24AWGwire.UseaULlistedpowersupply
withtherequiredoutputvoltageof12-36VDCtodeliverIEEE802.3atPoEPlus
onallPoEports(Ports1-4).Thepowersupplymustberatedasfollows:
• 802.3af-96Was(Minimum)
• 802.3at-168Was(Minimum)
1
Power Supply AC Power Input
12-36VDC/7A
(UL Listed)
V+
V-
Wiring Posive Power Supplies
Power Supply AC Power Input
12-24AWG
12-24AWG
V+
V-
DC Power Input
12-36VDC
12-36VDC
DC Power Input 12-36VDC/7A
(UL Listed)
Relay
PWR1PWR2
+
-+
-
Powershouldbedisconnectedfromthepowersupplybeforeconnecngitto
the switch. Otherwise, your screwdriver blade can inadvertently short your
terminalconneconstothegroundedenclosure.
1. InserttheposiveandnegavewiresintoPWR+andPWR-contacts
(PWR1andPWR2).Youcanconnectasinglepowersupplyortwopower
supplies depending on your requirements.
Ifbothpowerinputsareconnected,theES7206-XTwillbepowered
fromthehighestconnectedvoltage.Theunitcanbeconguredto
signalanalarmforlossofpowerineitherPWR1orPWR2.
2. Tighten the wire-clamp screws to prevent the wires from being
loosened.
Note: When the ES7206-XT is in operaon, cauon must be taken to not touch the hot
surface of the product enclosure.
Electrical Specicaons Value
PowerInput 12-36VDC
PowerConsumpon
(withoutPDloading) • 840mA@12VDC
• 420mA@24VDC
• 280mA@36VDC
PowerConsumpon
(withPDloading) • IEEE802.3af:6.25@12VDC
• IEEE802.3af:4A@24VDC
• IEEE802.3at:7A@24VDC
• IEEE802.3af:2.67A@36VDC
• IEEE802.3at:4.67A@36VDC
MaximumOutput/PowerPoEPort • 15W(IEEE802.3af)
• 30W(IEEE802.3at)
(table connued on next page)
2
3
Electrical Specicaons Value
Total PoE Power
Budget VIN=12VDC • 60W@-40°to70°C
• 55W@70°to75°C
VIN=24VDC • 110W@-40°to65°C
• 100W@65°to75°C
VIN=36VDC • 110W@-40°to65°C
• 100W@65°to75°C
Operang Temperature -40°to75°C
Storage Temperature -40°to85°C
Note: Exceeding the recommended power and operang temperatures may
result in failures or damage.
Wiring the Alarm Relay Output
Thealarmrelayoutputordigitaloutput(DO)contactsareontheterminal
block connector. The alarm relay output contacts are normally open. The
alarmrelayoutputcontactsclosewhenthealarmisenabledwiththeDIP
switches and there is a port link failure or PoE failure on a port.
Therelaycontactsupportsupto0.5Aat24VDC.Donotapplyvoltageand
currenthigherthanthespecicaons.
Thealarmrelayoutputiscontrolledbythepre-denedrules.Toacvatethe
alarmrelayoutputfuncon,refertothefollowingdrawing.
Earth Ground
+
Alarm Relay Output
DIP Switch
Alarm Control
Alarm
Relay
PWR2 PWR1
Power
Source
Buzzer/
PLC
Input
12 - 24
AWG Wire
24VDC/0.5A (Max)
Seng the DIP Switch
TheES7206-XThasan8-pinDIPswitchlocatedontheboompanelto
congurethePortLinkAlarmfortheEthernetports.Thefollowingtable
showstheDIPswitchnumbermappingtothecorrespondingopons.
Port
1
Port
2
Port
3
Port
4
Port
5
Port
6
PWR
Alm
SFP
100
DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 DIP8
ThistableshowstherelaonshipbetweentheDIPswitchnumber,posion,
andfuncon.
Switch Posion Funcon
1-6 ON Enables port failure alarm for corresponding port
OFF(Default) Disablesportfailurealarmforcorrespondingport
7ON Enables power event alarm
OFF(Default) Disablespowereventalarm
8ON EnablesSFPportfor100BASE-FX
OFF(Default) Supports Gigabit SFP in SFP port
Note: Aer connecng the SFP or changing the speed through DIP 8, cycle the
power to acvate the SFP.
Grounding the ES7206-XT
Wiretheearthgroundtoensurethesystemisnotdamagedbynoiseorany
electricalshock,werecommendthatyoumakeadirectconneconbetween
the ES7206-XT and earth ground.
Usingascrewdriver,loosentheearthgroundscrewontheboomof
theES7206-XTandthenghtenthescrewaertheearthgroundwireis
connected.
4
5
Mounng the ES7206-XT
TheDINrailclipisaachedtotheES7206-XT.
1. InserttheupperendofDINrailclipintothebackofDINrailtrackfrom
its upper side.
2. LightlypushtheboomofDINrailclipintothetrack.
3. VerifythattheDINrailclipisghtlyaachedonthetrack.
Note: When the ES7206-XT is in operaon, cauon must be taken to not
touch the hot surface of the product enclosure.
Connecng the RJ45 Ethernet Ports
Connect one end of an Ethernet cable into the Ethernet port of the
ES7206-XTandtheotherendtotheaachednetworkingdevice:
• Ports1-4areGigabitPoEportsthatsupportIEEE802.3af/802.3at(PoE+)
• Port5isaGigabit(10/100/1000BASE-TX)port
• Port6isaGigabitSFPport,whichisdiscussedinthenextsecon
TheportssupportGigabithalf/full-duplex.AllRJ45portsauto-detectthe
signalfromconnecteddevicestonegoatethelinkspeedandduplexmode.
AutoMDI/MDIXallowsuserstoconnectanotherswitch,hub,orworkstaon
without changing straight-through or crossover cables.
Link/ActLEDsarelittoindicatetracandlinkstatus,seetheLEDssubsecon
formoreinformaon.
1000BASE-TX
Alwaysmakesurethatthecablesbetweentheswitchesandaacheddevices
(forexample,switch,hub,orworkstaon)arelessthan100meters(328
feet).YoushoulduseCategory5cableorhigher.
Connecng the SFP Port
You can connect an SFP transceiver to Port 6. Comtrol recommends using
Comtrol-approved SFP transceivers. Cross-connect the transmit channel at
each end to the receive channel at the opposite end as illustrated in the
gure.
MakesurethatyouuseanSFPbertransceivercompliantwithUL
cercaonandEN60825Class1.
LED INDICATORS
LED Status Descripon
PWR1/2 Green The terminal block is receiving power
O The terminal block is not receiving power
(table connued on next page)
6
A B
TX
RX
TX
RX
LED Status Descripon
Alm Red Oneofthefollowinghasoccurred:
• Port link failure has occurred
• PowerhasbeenremovedfromPWR1orPWR2
• Port6SFPis100BASE-FXandhaslost
connecon/link
O Nofailurehasbeenfound
PoE 1-4 Yellow TheportisprovidingPoEpowertothePD
O NoPDisaached
P 1-5
LNK/ACT
Green Anetworkdeviceisaached
Blinks ThereisavalidEthernettransmit/receiveacvity
to/from the connected network device
O Theportlinkisnotacve
P6
LNK
Green Anetworkdeviceisaached
Blinks ThereisavalidEthernettransmit/receiveacvity
to/from the connected network device.
O Theportlinkisnotacve
COMTROL CUSTOMER SERVICE
You can use one of the following methods to contact Comtrol.
Contact Method Web Address or Phone Number
Support hp://www.comtrol.com/support
Downloads p://p.comtrol.com/html/default.htm
Website hp://www.comtrol.com
Phone +1763.957.6000
7
Inhaltsverzeichnis
Andere Comtrol Schalten Handbücher
Comtrol
Comtrol Rocket linx ES8508 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES8108 Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES8509-XT Bedienungsanleitung
Comtrol
Comtrol ROCKET LINX ES7506 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES7510 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES7506 Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES8509-XT Bedienungsanleitung
Comtrol
Comtrol ROCKET LINX MP1204-XT Bedienungsanleitung
Comtrol
Comtrol RocketPort RPUSBSH Bedienerhandbuch
Comtrol
Comtrol RocketLinx ES8108 Bedienungsanleitung
Comtrol
Comtrol RocketPort Serial Hub Si Bedienerhandbuch
Comtrol
Comtrol ROCKET LINX ES7506 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES7528 Bedienungsanleitung
Comtrol
Comtrol RocketLinx MP1204-XT Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ACS7106 Bedienungsanleitung
Comtrol
Comtrol RocketLinx ES8108 Bedienungsanleitung
Comtrol
Comtrol ROCKETLINX ES7105 Bedienungsanleitung
Comtrol
Comtrol RocketPort Stücklistenhandbuch
Comtrol
Comtrol ROCKETLINX ES8508 Bedienungsanleitung
Comtrol
Comtrol Rocketlinx ES8108-GigE Bedienungsanleitung
