Conceptronic CMED3PLUS Kurzanleitung

www.conceptronic.net

Page 1 of 7

Conceptronic CMED3PLUS Firmware Upgrade Instructions

for firmware version: 1 54B / MP07T031408A

A Upgrade information

The Conceptronic CMED3PLUS is equipped with an upgradeable firmware chip This function makes it

possible to improve the device and to add new features

Note: This firmware upgrade for the CMED3PLUS can onl be applied to devices with firmware version

1.54 (MP07T022408A) or higher. If ou have a lower version ou need to upgrade to version

1.54 before ou can appl this firmware upgrade.

Note: The firmware upgrade procedure is at our own risk. Even though a firmware upgrade can

improve the device and add new features, there’s also a possibilit of an upgrade failure which

makes the device unusable. Conceptronic is not responsible for this and this voids the warrant .

www.conceptronic.net

Page 2 of 7

B WARNING !!!

There are two different versions of the Conceptronic Media Player on the market Both versions only

differ in hard disk connection type (SATA vs IDE) and the supplied remote control Since the devices are

so similar it is mandatory to pick out the right product when upgrading the firmware The easiest way to

identify your Media Player is through the remote control

Below you see an image of both remote controls, continue this firmware upgrade procedure only when

you have the LEFT remote control

www.conceptronic.net

Page 3 of 7

C Upgrade procedure from the internal hard disk of the CMED3PLUS

1 Copying the firmware files to the CMED3PLUS

1 1 If you have downloaded the firmware upgrade from www conceptronic net, you have a ZIP file

containing a folder named ‘FW’ and three documentation files

1 2 Connect the CMED3PLUS to your computer with the USB cable

1 3 Copy the ‘FW’ folder including all its content to the hard disk of the CMED3PLUS

1 4 Remove the CMED3PLUS from your computer with the ‘Safely remove hardware’ option

1 5 Disconnect the USB cable of the CMED3PLUS and turn it off with the switch on the back side

2 Updating the firmware

2 1 Connect the CMED3PLUS to a TV or monitor

2 2 Turn on the CMED3PLUS with a remote control

2 3 Select the ‘FW’ folder by using the navigation buttons on the remote control

The upgrade process will now start This will be visible in the upper left corner with the terms

‘ERASE’ and ‘WRITE’

Note: The CMED3PLUS must not be turned off during the upgrade process. Doing so will

result in an unusable product which is not covered b the warrant .

2 4 As soon as the upgrade process is completed, the screen will go black

Note: The device is still turned on. You need to manuall turn off the device b pressing the

‘POWER’ button on the remote control. You can completel turn the device off b

turning off the switch on the back side of the device.

3 Removing the ‘FW’ folder

3 1 Connect the CMED3PLUS to your computer with the USB cable

3 2 Remove the ‘FW’ folder from the hard disk This makes sure the CMED3PLUS won’t start

updating again when the ‘FW’ folder is selected on your TV or monitor

3 3 Remove the CMED3PLUS from your computer with the ‘Safely remove hardware’ option

3 4 Disconnect the USB cable from the CMED3PLUS and turn it off with the switch on the back side

www.conceptronic.net

Page 4 of 7

4 Checking the current firmware version

4 1 Make sure the CMED3PLUS is connected to a TV or monitor

4 2 Select a folder by using the navigation buttons on the remote control

4 3 Press the ‘FUNC’ button on the remote control, select ‘PROPERTIES’ and press the ‘Enter’

button

4 4 Now press the ‘Pause’ button ( II ) five (5) times in a row

4 5 Leave the current screen by pressing the ‘FUNC’ button

4 6 When the ‘Fast Forward’ button ( >> ) is pressed, the current firmware version will be shown

This must be: VER 32-O MP07T031408A-2L

4 7 If the version isn’t shown long enough, you need to press the ‘Fast Forward’ button again

4 8 If the displayed version isn’t the same as the version described at point 4 6, then you need to

repeat the upgrade procedure as described in chapter C

D Upgrade procedure from a USB stick or memory card

1 Copying the firmware files to a USB stick or a memory card

1 1 If you have downloaded the firmware upgrade from www conceptronic net, you have a ZIP file

containing a folder named ‘FW’ and three documentation files

1 2 Connect the USB stick or memory card to your computer

1 3 Copy the ‘FW’ folder including all its content to the USB stick or memory card

1 4 Remove the USB stick or memory card from your computer with the ‘Safely remove hardware’

option

1 5 Disconnect the USB stick or memory card from your computer

2 Updating the firmware

2 1 Make sure the CMED3PLUS is connected to a TV or monitor

2 2 Turn on the CMED3PLUS with the remote control

2 3 Connect the USB stick to the CMED3PLUS or slide the memory card in the right card slot of the

CMED3PLUS

2 4 A screen will be displayed in which you can make the choice between ‘HARD DISK’ and ‘USB

DEV’ / ‘<memory card>’, where ‘<memory card>’ is the used memory card type (for instance

‘COMPACT FLASH’) Choose the option of the USB stick or memory card

2 5 Select the ‘FW’ folder by using the navigation buttons on the remote control

The upgrade process will now start This will be visible in the upper left corner with the terms

‘ERASE’ and ‘WRITE’

Note: The CMED3PLUS must not be turned off during the upgrade process. Doing so will

result in an unusable product which is not covered b the warrant . The same applies

to removing the USB stick or memor card.

www.conceptronic.net

Page 5 of 7

2 6 As soon as the upgrade process is completed, the screen will go black

Note: The device is still turned on. You need to manuall turn off the device b pressing the

‘POWER’ button on the remote control. You can completel turn the device off b

turning off the switch on the back side of the device.

2 7 Remove the USB stick or memory card from the device

Note: Never do this when the device is turned on and the upgrade process is bus . This will

result in an unusable product.

3 Checking the firmware version

3 1 Make sure the CMED3PLUS is connected to a TV or monitor

3 2 Select a folder by using the navigation buttons on the remote control

3 3 Press the ‘FUNC’ button on the remote control, select ‘PROPERTIES’ and press the ‘Enter’

button

3 4 Now press the ‘Pause’ button ( II ) five (5) times in a row

3 5 Leave the current screen by pressing the ‘FUNC’ button

3 6 When the ‘Fast Forward’ button ( >> ) is pressed, the current firmware version will be shown

This must be: VER 32-O MP07T031408A-2L

3 7 If the version isn’t shown long enough, you need to press the ‘Fast Forward’ button again

3 8 If the displayed version isn’t the same as the version described at point 3 7, then you need to

repeat the upgrade procedure as described in chapter D

www.conceptronic.net

Page 6 of 7

E Release notes

1 54B / MP07T031408A:

- Fixed: Characters ‘ö’ and ‘ü’ for German language did not display correctly

1 54 / MP07T022408A:

- Fixed: SMI subtitles larger than 200 kB are now displayed correctly

- Added: Support for SMI files with multiple subtitles

- Added: Copy function: It is now possible to copy data from the internal hard disk to a USB device

MP07T081007A:

- Subtitles: “Latin2” character support for countries like Hungary, Bulgaria, etc

MP07T062807A:

- Subtitle problems for European countries solved

MP07T061107A:

- Subtitle files load automatically when a video starts to play (when the subtitle file and the video file

have the same file name) A single folder can now contain up to 30 movies with a subtitle file Previously

this was limited to 10

- When playback is paused, it is possible to let the screensaver start, but no longer the standby mode

MP07T032707A:

- DVD navigation problems solved:

‘Fast Forward’ and ‘Fast Rewind’ now work and some small DVD playback problems are solved

MP07T101806A:

- Problem with time information during playback is solved

- Problem with the default PAL setting is solved

MP07T092106A:

- Auto start function added

- Some minor internal changes

- DVD menu navigation support added (see chapter G for an explanation)

www.conceptronic.net

Page 7 of 7

F Summary of DVD menu navigation functions

To playback a DVD with menu navigation, you need to do the following:

1 Copy all files from the DVD to a folder on the hard disk of the CMED3PLUS The name of the folder

can be anything (for example: ‘DVD_DISC1’) The DVD folder structure however, has to be

maintained This means that the ‘VIDEO_TS’ folder always has to be present in the movies’ folder (in

this case ‘DVD_DISC1’) The ‘AUDIO_TS’ folder is not necessary, unless there are files inside

2 To start DVD menu navigation, you need to navigate to the ‘DVD_DISC1’ folder and press the right

navigation button on the remote control In case you press the ‘Enter’ button, you will see the folder

contents If this happens, go back to folder above it and press the right navigation button on the

remote control

3 Press the ‘SUBTI’ button to select a subtitle

4 Press the ‘AUDIO’ button to select a spoken language

5 Press the ‘FUNC’ button to see information about the current file

6 Press the ‘<<’ or ‘>>’ button to fast forward or fast rewind

7 Press the ‘I<<’ or ‘>>I’ button to select a previous or next chapter

8 Press the ‘II’ button to pause the playback

9 Press the ‘▀’ button to stop the playback and leave the menu navigation

10 Press the ‘ZOOM’ button to zoom in or out

11 Press the ‘VOL-‘ or ‘VOL+’ button to adjust the volume

12 Press the ‘MUTE’ button the turn off the sound, press it again to turn on the sound

13 Press the ‘A-B’ button to repeat a certain part of the video

14 Press the ‘REPEAT’ button the change the repeat function Possibilities are:

- CHAPTER REPEAT: repeats the current chapter

- TITLE REPEAT: repeats the current title

- REPEAT OFF: turns off all repeat functions

Inhaltsverzeichnis

Andere Conceptronic Medienplayer Handbücher

Conceptronic

Conceptronic CM3HD Bedienungsanleitung

Conceptronic

Conceptronic Grab'n'GO 3,5" Bedienungsanleitung

Conceptronic

Conceptronic Grab'n'Go MediaGiantPlus CM3GP Bedienungsanleitung

Conceptronic

Conceptronic cm3pvrd Bedienungsanleitung

Conceptronic

Conceptronic CMED3PRO Bedienungsanleitung

Conceptronic

Conceptronic CM3PVR Kurzanleitung

Conceptronic

Conceptronic CSM3PL Kurzanleitung

Conceptronic

Conceptronic C54WMP Bedienungsanleitung

Conceptronic

Conceptronic CM3S Kurzanleitung

Conceptronic

Conceptronic CSM3PL Bedienungsanleitung

Conceptronic

Conceptronic cm3pvrd Kurzanleitung

Conceptronic

Conceptronic CFULLHDMAi Bedienungsanleitung

Conceptronic

Conceptronic CSM3NET Bedienungsanleitung

Conceptronic

Conceptronic Media Giant Bedienungsanleitung

Conceptronic

Conceptronic CM3PVR Bedienungsanleitung

Conceptronic

Conceptronic CFULLHDMA Bedienungsanleitung

Conceptronic

Conceptronic CMED2PRO Bedienungsanleitung

Conceptronic

Conceptronic Media Giant CM3G Series Gebrauchs- und Pflegehandbuch

Conceptronic

Conceptronic cm3pvrd Kurzanleitung

Conceptronic

Conceptronic CM3H Bedienungsanleitung

Conceptronic

Conceptronic Media Giant Benutzerhandbuch

Conceptronic

Conceptronic CMED2PLAY Bedienungsanleitung

Conceptronic

Conceptronic CMED3PLAY Bedienungsanleitung

Conceptronic

Conceptronic CSM3PL Kurzanleitung

Beliebte Medienplayer Handbücher anderer Marken

Visual Land

Visual Land Impulse Bedienungsanleitung

Transcend

Transcend DMP10 Bedienungsanleitung

Philips

Philips GoGear Muse SA2MUS08 Bedienungsanleitung

Fantec

Fantec MM-HDRL Bedienungsanleitung

Dune HD

Dune HD Duo 4K Bedienungsanleitung

IAdea

IAdea HMP-505S Bedienungsanleitung

Camos

Camos MMS-1000 Bedienungsanleitung

Energy

Energy 75 Series Bedienungsanleitung

Z3 Technology

Z3 Technology DME-03 Bedienungsanleitung

Sony

Sony SVR-2000 Benutzerhandbuch

Meicheng

Meicheng HD-1080K12 Bedienungsanleitung

DENAFRIPS

DENAFRIPS ARCE Bedienungsanleitung

Topaz

Topaz CMS Media Player Gebrauchsanweisung

InFocus

InFocus LightCast Bedienungsanleitung

IconBiT

IconBiT XDS1003D Bedienungsanleitung

Quanmax

Quanmax QDSP-2090 Series Bedienungsanleitung

Samsung

Samsung MP-80S Bedienungsanleitung

Trigon Elektronik

Trigon Elektronik CHRONOLOG Bedienungsanleitung