Conceptronic CSM3PL Kurzanleitung

www.conceptronic.net

Page 1 of 7

Conceptronic CSM3PL Firmware Upgrade Instructions

for firmware version 1.58 BETA

A. Upgrade information

The Conceptronic CSM3PL is equipped with an upgradeable firmware chip. This function makes it

possible to improve the device and to add new features.

Note: This firmware upgrade for the CSM3PL can only be applied to devices with firmware version

.54 (MP07ST022408A) or higher. If you have a lower version you need to upgrade to version

.54 before you can apply this firmware upgrade.

Note: The firmware upgrade procedure is at your own risk. Even though a firmware upgrade can

improve the device and add new features, there’s a small possibility of an upgrade failure

which makes the device unusable.

www.conceptronic.net

Page 2 of 7

B. WARNING !!!

There are two different versions of the Conceptronic Media Pla er on the market. Both versions onl

differ in hard disk connection t pe (SATA vs. IDE) and the supplied remote control. Since the devices are

so similar it is mandator to pick out the right product when upgrading the firmware. The easiest wa to

identif our Media Pla er is through the remote control.

Below ou see an image of both remote controls, continue this firmware upgrade procedure onl when

ou have the MI LE or RIGHT remote control (CSM3PL rev. 1 or CSM3PL rev. 2).

www.conceptronic.net

Page 3 of 7

C. Upgrade procedure from the internal hard disk of the CSM3PL

1. Copying the firmware files to the CSM3PL

1.1 If ou have downloaded the firmware upgrade from www.conceptronic.net, ou have a ZIP file

containing a folder named ‘Firmware’ and three documentation files.

1.2 Connect the CSM3PL to our computer with the USB cable.

1.3 Cop the ‘Firmware’ folder including all its content to the hard disk of the CSM3PL.

1.4 Remove the CSM3PL from our computer with the ‘Safely remove hardware’ option.

1.5 Disconnect the USB cable of the CSM3PL and turn it off with the switch on the back side.

2. Updating the firmware

2.1 Connect the CSM3PL to a TV or monitor.

2.2 Turn on the CSM3PL with the switch on the back side.

2.3 Select the ‘Firmware’ folder b using the navigation buttons on the remote control.

A confirmation screen will be displa ed asking if ou want to replace the current firmware with a

new one. Choose ‘Yes’. The upgrade process will start. This is visible in the upper left corner

with the terms ‘ERASE’ and ‘WRITE’.

Note: The CSM3PL must not be turned off during the upgrade process. Doing so will

result in an unusable product which is not covered by the warranty.

2.4 As soon as the upgrade process is completed, the screen will go black.

Note: The device is still turned on. You need to manually turn off the device by pressing the

‘POWER’ button on the remote control. You can completely turn the device off by

turning off the switch on the back side of the device.

3. Removing the ‘Firmware’ folder

3.1 Connect the CSM3PL to our computer with the USB cable.

3.2 Remove the ‘Firmware’ folder from the hard disk. This makes sure the CSM3PL won’t start

updating again when the ‘Firmware’ folder is selected on our TV or monitor.

3.3 Remove the CSM3PL from our computer with the ‘Safely remove hardware’ option.

3.4 Disconnect the USB cable from the CSM3PL and turn it off with the switch on the back side.

www.conceptronic.net

Page 4 of 7

4. Checking the current firmware version

4.1 Make sure the CSM3PL is connected to a TV or monitor.

4.2 Press the “SETUP” button on the remote control.

4.3 Highlight the “FIRMWARE VERSION” option. The firmware version is displa ed on the lower left

corner. This should be “CSM3PL_FW_VER_1.58 ”.

4.4 If the displa ed version isn’t the same as the version described at point 4.3, then ou need to

repeat the upgrade procedure as described in chapter C.

. Upgrade procedure from a USB stick or memory card

1. Copying the firmware files to a USB stick or a memory card

1.1 If ou have downloaded the firmware upgrade from www.conceptronic.net, ou have a ZIP file

containing a folder named ‘Firmware’ and three documentation files.

1.2 Connect the USB stick or memor card to our computer.

1.3 Cop the ‘Firmware’ folder including all its content to the USB stick or memor card.

1.4 Remove the USB stick or memor card from our computer with the ‘Safely remove hardware’

option.

1.5 Disconnect the USB stick or memor card from our computer.

2. Updating the firmware

2.1 Make sure the CSM3PL is connected to a TV or monitor.

2.2 Turn on the CSM3PL with the remote control.

2.3 Connect the USB stick to the CSM3PL or slide the memor card in the right card slot of the

CSM3PL.

2.4 A screen will be displa ed in which ou can make the choice between ‘HAR ISK’ and ‘USB

EV’ / ‘<memory card>’, where ‘<memory card>’ is the used memor card t pe (for instance

‘COMPACT FLASH’). Choose the option of the USB stick or memor card.

2.5 Select the ‘Firmware’ folder b using the navigation buttons on the remote control.

A confirmation screen will be displa ed asking if ou want to replace the current firmware with a

new one. Choose ‘Yes’. The upgrade process will start. This is visible in the upper left corner

with the terms ‘ERASE’ and ‘WRITE’.

Note: The CSM3PL must not be turned off during the upgrade process. Doing so will

result in an unusable product which is not covered by the warranty.

www.conceptronic.net

Page 5 of 7

2.6 As soon as the upgrade process is completed, the screen will go black.

Note: The device is still turned on. You need to manually turn off the device by pressing the

‘POWER’ button on the remote control. You can completely turn the device off by

turning off the switch on the back side of the device.

2.7 Remove the USB stick or memor card from the device.

Note: Never do this when the device is turned on and the upgrade process is busy. This will

result in an unusable product.

3. Checking the current firmware version

3.1 Make sure the CSM3PL is connected to a TV or monitor.

3.2 Press the “SETUP” button on the remote control.

3.3 Highlight the “FIRMWARE VERSION” option. The firmware version is displa ed on the lower left

corner. This should be “CSM3PL_FW_VER_1.58 ”.

3.4 If the displa ed version isn’t the same as the version described at point 3.3, then ou need to

repeat the upgrade procedure as described in chapter D.

www.conceptronic.net

Page 6 of 7

E. Release notes

1.58 BETA:

Added:

- Support for NTFS hard disk. Please note that the cop function has been disabled in this firmware,

since this does not work in combination with NTFS.

1.57E:

Changed:

- Hard disk space indicator in the root has been removed to increase boot time performance.

Fixed:

- 2 GB file cannot be pla ed through USB.

1.57 :

Improved:

- Boot time.

1.55A / MP07ST052808A:

Fixed:

- Subtitles now show 47 letters on each line spread out over a maximum of 4 lines.

This should ensure that subtitles are shown in a much better manner.

1.55 / MP07ST022808A:

Fixed:

-Hard disk partition limitation: It is not needed an more for the first partition to be smaller than 137

GB. You can now partition the hard disk an which wa .

Note: It is possible to use both FAT32 and NTFS partitions on the CSM3PL. However, NTFS

partitions cannot be used by the Media Player function, only by a Windows XP or Vista

computer. All media should be placed on a FAT32 partition.

1.54 / MP07ST022408A:

Added:

-Support for SMI files with multiple subtitles.

-Cop function: it is now possible to cop data from the internal hard disk to a USB device.

Fixed:

-SMI subtitles larger than 200 kB are now displa ed correctl .

www.conceptronic.net

Page 7 of 7

MP07ST081007A:

Added:

-Subtitles: “Latin2” character support for countries like Hungar , Bulgaria, etc.

MP07T052907A:

-Initial release.

Andere Handbücher für CSM3PL

Inhaltsverzeichnis

Andere Conceptronic Medienplayer Handbücher

Conceptronic

Conceptronic CMED3PLAY Bedienungsanleitung

Conceptronic

Conceptronic C54WMP Bedienungsanleitung

Conceptronic

Conceptronic CMED2PLAY Bedienungsanleitung

Conceptronic

Conceptronic cm3pvrd Bedienungsanleitung

Conceptronic

Conceptronic cm3pvrd Kurzanleitung

Conceptronic

Conceptronic CMT2D Bedienungsanleitung

Conceptronic

Conceptronic CFULLHDMAi Bedienungsanleitung

Conceptronic

Conceptronic CM3PVR Kurzanleitung

Conceptronic

Conceptronic Grab'n'Go MediaGiantPlus CM3GP Bedienungsanleitung

Conceptronic

Conceptronic cm3pvrd Installations- und Benutzerhandbuch

Conceptronic

Conceptronic CFULLHDMA Bedienungsanleitung

Conceptronic

Conceptronic CSM3NET Bedienungsanleitung

Conceptronic

Conceptronic Media Giant CM3G Series Gebrauchs- und Pflegehandbuch

Conceptronic

Conceptronic CM2H Bedienungsanleitung

Conceptronic

Conceptronic cm3pvrd Kurzanleitung

Conceptronic

Conceptronic CM3HD Bedienungsanleitung

Conceptronic

Conceptronic Media Giant Benutzerhandbuch

Conceptronic

Conceptronic CM3S Kurzanleitung

Conceptronic

Conceptronic CM3S Bedienungsanleitung

Conceptronic

Conceptronic CMED3PRO Bedienungsanleitung

Conceptronic

Conceptronic CM3PVR Installations- und Benutzerhandbuch

Conceptronic

Conceptronic Grab'n'GO 3,5" Bedienungsanleitung

Conceptronic

Conceptronic Media Giant Bedienungsanleitung

Conceptronic

Conceptronic CM3PVR Bedienungsanleitung

Beliebte Medienplayer Handbücher anderer Marken

Visual Land

Visual Land Impulse Bedienungsanleitung

Transcend

Transcend DMP10 Bedienungsanleitung

Philips

Philips GoGear Muse SA2MUS08 Bedienungsanleitung

Fantec

Fantec MM-HDRL Bedienungsanleitung

Dune HD

Dune HD Duo 4K Bedienungsanleitung

IAdea

IAdea HMP-505S Bedienungsanleitung

Camos

Camos MMS-1000 Bedienungsanleitung

Energy

Energy 75 Series Bedienungsanleitung

Z3 Technology

Z3 Technology DME-03 Bedienungsanleitung

Sony

Sony SVR-2000 Benutzerhandbuch

Meicheng

Meicheng HD-1080K12 Bedienungsanleitung

DENAFRIPS

DENAFRIPS ARCE Bedienungsanleitung

Topaz

Topaz CMS Media Player Gebrauchsanweisung

InFocus

InFocus LightCast Bedienungsanleitung

IconBiT

IconBiT XDS1003D Bedienungsanleitung

Quanmax

Quanmax QDSP-2090 Series Bedienungsanleitung

Samsung

Samsung MP-80S Bedienungsanleitung

Trigon Elektronik

Trigon Elektronik CHRONOLOG Bedienungsanleitung