Conrad-johnson design ET2 Vacuum Bedienungsanleitung

Conrad-Johnson Owner’s Manual:

ET2 Vacuum-Tube Preamplifier

conrad-johnson It just sounds right.

ET2 Owner’s Manual 1

Thank you for selecting the ET2 vacuum-tube preamplifier as the

control center for your audio system. Using it, we believe that you

will hear more from your favorite recordings than ever before.

Drawing on nearly three decades of research at conrad-johnson

into the reproduction of recorded music, the ET2 excels at the rec-

reation of the dynamics, textures, tonalities, and ambience of live

musical performances.

At conrad-johnson, we expect our products to be a source of satis-

faction and of pride to their owners for many years to come. Ac-

cordingly, circuit designs, parts and materials have been selected

with a view to maintaining optimal performance over the years. Our

reputation for producing among the industry's most reliable com-

ponents is a natural consequence of this engineering approach.

Although the ET2 has been designed to operate in an intuitively

apparent way, you will find useful information on its installation and

operation in this manual. Please take a few minutes to read the

manual to better understand the features and capabilities of your

ET2. Note that this unit is phase inverting. See the section entitled

"Getting the most from your ET2" for details on correct hookup in

your system.

In closing, we'd like to welcome you to the family of conrad-johnson

owners. We want you to enjoy your conrad-johnson product to the

fullest. To this end, our staff stands ready to answer any questions

you may have about the function and application of your ET2, and

to provide any needed service both during, and after the warranty

period. Our goal is to heighten your enjoyment of recorded music.

ET2 Owner’s Manual 2

imited Warranty For Conrad-Johnson Components

Conrad-Johnson Design, Inc. will provide service under warranty to

the original owner on products sold new in the United States for the

lesser period of three years from the date of purchase by the origi-

nal purchaser, or five years from the date of shipment to the au-

thorized conrad-johnson dealer. During the warranty period, con-

rad-johnson will repair defective units without charge for labor or

parts (with the exception of vacuum tubes and batteries).

Exclusions. The following are not covered under this warranty:

a) Units which have been damaged by misuse, abuse, or acci-

dent.

b) Units which have been modified, altered, or improperly re-

paired by anyone not specifically authorized by conrad-johnson

design, inc.

c) Units not purchased from an authorized conrad-johnson

dealer in the United States for use in the United States.

d) Normal wear

e) Incidental or consequential damages are not covered under

this warranty. Some states do not allow the exclusion of inci-

dental or consequential damages, so this exclusion may not

apply to you.

Obtaining Warranty Service: To obtain warranty service, the unit

must be shipped, along with evidence of purchase, in factory pack-

ing to conrad-johnson design (or designated service center) with

freight and insurance prepaid by the owner. After repair, the unit

will be returned with freight and insurance prepaid by conrad-

johnson design to any destination in the United States.

All implied warranties, including merchantability and fitness for a

particular purpose are limited in duration to the duration of this ex-

press warranty. Some states do not allow limitations on the dura-

tion of implied warranties so the above limitations may not apply to

you.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

ET2 Owner’s Manual 3

Conrad-Johnson products purchased outside the United States are

covered by warranty terms of the importing distributor in the coun-

try in which the product was originally purchased, which may differ

from the terms set out herein. Importing distributors are not obli-

gated to provide warranty service for products originally purchased

outside their country. Conrad-Johnson will provide warranty service

for products outside the United States, but in these cases, the cus-

tomer must pay all shipping, handling and customs costs both to

and from our Service Department.

Questions about this warranty should be addressed to:

Service Department

conrad-johnson design, inc.

2733 Merrilee Drive

Fairfax, VA 22031

The conrad-johnson service department can also be reached by e-

mail at [email protected], by phone at 703-698-8581,

or by fax at 703-560-5360.

Service

If your conrad-johnson audio component requires service, repack it

using the original box and packing material and ship to the Service

Department address above. Boxes and packing materials can be

purchased through our service department if you no longer have

yours. Include with the unit a note describing the problem you are

having in as much detail as possible. It is especially important for

our technician to know if the problem is intermittent. If you want an

estimate of cost for out of warranty service, be sure to request it in

this note. Be aware that requesting an estimate will delay service

to your unit, as we will have to contact you for approval before

commencing service.

Registering The Warranty

Please return the enclosed card to the factory within 30 days of

purchase to register the warranty

ET2 Owner’s Manual 4

nstallation

The ET2 dissipates approximately 20 watts of heat, and must be

adequately ventilated. Mount the unit horizontally on a flat, hard

surface, and take care that the ventilation holes in the bottom are

unobstructed. Allow at least two inches of clearance above the unit

and keep the cabinet or shelf open at the back. Vertical installation

is not recommended.

All ET2s sold in the United States are configured for operation on a

60Hz ac power line producing between 108 and 126 volts. Export

versions of the ET2 will have the correct operating voltage and fre-

quency clearly marked on the back panel of the unit, near the ac

power cord. In all cases, the actual line voltage should be within +

5/-10% of the nominal rated voltage.

Electromagnetic Interference (EMI)

Considerable care has been taken in the design of the ET2 to

minimize its susceptibility to radio frequency interference and other

forms of EMI. Choice of materials, physical layout, grounding prac-

tice, and power supply design have all been specified with a view

to reducing the impact of electromagnetic fields on the perform-

ance of this unit. At the same time, however, our primary goal is

the accurate reproduction of recorded music in the normal home

environment, and we have elected not to compromise this objec-

tive by the application of heavy-handed RFI filters, or by using

grounding practices that reduce RFI at the expense of degraded

audio performance. We find that the approach we have taken has

worked extremely well, resulting in only rare instances of EMI prob-

lems which could be treated locally as needed, rather than com-

promising the performance of our product in the 99.9% of installa-

tions where EMI is not a problem.

Care in installation can often avoid EMI induced problems. The fol-

lowing practices should generally be observed in any application,

and will be especially important where EMI may be a problem.

Interconnect cables should be kept as short as possible (3 meters

or less), and shielded cable should be used (cable which has two

center conductors, and a separate external shield connected at

only one end).

ET2 Owner’s Manual 5

Physical location and cable “dress” can be an important factor in

minimizing hum pickup. The installation should situate the pream-

plifier well away from the power amplifier, and power (ac mains)

cords should be dressed to remain at least 4" (100mm) away from

input/output cables.

ET2 Owner’s Manual 6

onnection

SOURCES (TUNER, CD, VIDEO, AUX2): These high level inputs

are electrically equivalent. These inputs present a 13.5 kOhm load

to the source. Connect the corresponding source components to

these inputs.

PH/AUX1: If the optional phono stage is installed, this input pro-

vides the extra gain and RIAA equalization required for playback of

LPs. Otherwise, this serves as an additional line-level input.

EPL: This set of line-level inputs and outputs provides for connec-

tion of an external signal processor (e.g. parametric equalizer, tone

controls) or a tape recorder. Connect the EPL OUT to the input of

your signal processor or tape recorder, and the EPL IN to the out-

put of your processor or tape recorder. Alternatively, the EPL IN

connection can be used as an additional line level input.

THEATER: This is an external processor loop designed to conven-

iently accommodate the addition of a surround-sound processor

(SSP) to a high-quality two-channel system without compromising

two-channel performance. Connect the front left and front right

channel outputs from your SSP to THEATER IN. You can also con-

nect the THEATER OUT to an input on your SSP, allowing you to

do signal processing on selected two channel sources. When

THEATER is selected, the level controls are set and locked to unity

gain. Level and balance control are then accomplished via your

surround sound processor.

MAIN OUT: Two pairs of main outputs are provided. Connect to

the input of your amplifier (or crossover in a bi-amplified system).

We recommend the use of an amplifier with an input impedance of

20k ohms or higher. Since the ET2 inverts phase, it may be neces-

sary to invert the speaker leads to maintain correct absolute phase.

See the section on “Getting the most out of your ET2" for an expla-

nation.

TRIGGER OUTPUT: When the ET2 is switched on, these termi-

nals provide a constant dc voltage that can be sensed by the “trig-

ger” circuits used to switch on some power amplifiers. If your am-

plifier employs such a trigger circuit, and you wish to switch it on

and off from the preamplifier, connect this output to the trigger in-

put on your amplifier. Observe the coded polarities center pin is

positive).

ET2 Owner’s Manual 7

ontrols

<power>: Press the switch labeled power to switch the preampli-

fier on. A time delay auto-muting circuit is incorporated into the

ET2 to suppress turn-on/turn-off transients. All outputs are

grounded via relays for approximately 45 seconds after the unit is

turned on in order to suppress warm-up transient noises. During

auto-muting, the mute indicator led will flash. Level and balance

control functions are disabled during the auto-muting cycle. The

muting relay also grounds the outputs immediately at turn-off or in

the event of any power line interruption.

When first connected to ac mains, or after an interruption of power,

the ET2 will turn on in a default mode (after auto-muting), with the

level set at 40, and the CD input selected. In subsequent sessions,

as long as the ac mains has not suffered a power outage, the unit

will turn on at the last used volume setting and input.

<mute>: Pressing the mute button will silence the preamplifier

main outputs, and set the level display to zero on both channels.

Pressing the mute button again will restore the previously selected

level setting.

<level up>, <level down>: Level setting on the ET2 can be ad-

justed in 0.5 dB increments. The level setting can be changed by

pressing the level up and level down buttons on the front panel.

Each time a button is pressed, the level will move up or down 0.5

dB. If a button is pressed and held, the level control will cycle

through the steps at an accelerating rate. Balance can only be set

using the remote control and is also adjusted in 0.5 dB increments.

<source>: Pressing the button labeled source will cause the unit

to step through the five source inputs (ph/aux, tuner, cd, video,

aux2). The selected input will be indicated by an illuminated led.

<epl/thtr>: Pressing the epl/thtr button will cause the unit to step

from source through epl1 and theater. When source is selected,

the input selected by the source selector will be passed directly to

the volume control. When the EPL1 or THEATER inputs are se-

lected, the selected source will first pass through the external

processor loop before being routed to the volume control. When

THEATER is selected, the level will be set and locked to unity gain.

ET2 Owner’s Manual 8

Remote Control

All operations of the ET2 can be controlled by the wireless remote

unit.

MUTE: Pressing the mute button will cause the main outputs to

mute and the level display to be zero. Pressing it again will restore

the last level setting. Pressing and holding the mute button for

more than three seconds will switch the ET2 into standby mode (all

tube circuitry switched off). Pressing the mute button when the unit

is in standby mode will switch it back on.

SELECTORS (PH/AUX, TUNER, CD, VIDEO, AUX2): You can di-

rectly access any of these inputs by pressing the associated button

on the remote.

EPLS (EPL1, EPL2): Pressing the EPL buttons inserts the associ-

ated processor in the signal path. Pressing the button again will re-

establish a direct connection to the selected source. Pressing the

EPL2 button selects the THEATER input, setting and locking the

level to unity gain.

LEVEL (+, -): Duplicates the function of the front panel <level up>,

<level down> controls.

BALANCE: Allows attenuation of either channel independently of

the other. Pressing the right balance button will reduce the left

channel level setting by one step. Pressing and holding the right

balance button will cause the left channel to cycle down through its

level settings at an accelerating rate. Pressing the left balance but-

ton will attenuate the right channel in the same manner.

ET2 Owner’s Manual 9

acuum Tube Replacement

The audio circuit of the ET2 uses two type 8080 miniature triode

vacuum tubes. The brand of tubes we supply has been chosen by

first selecting those brands which are known to be most reliable,

then by extensive auditioning of these acceptable brands with the

final choices being made solely on the basis of sonic performance.

We know of no vacuum tubes available which will improve the

sonic performance of your ET2. The tubes in your preamplifier

have been tempered by a controlled burn-in procedure that permits

them to perform for a greatly extended period without sonic degra-

dation, then selected for minimum residual noise. Replacement

tubes are prepared and selected in the same way. Therefore, we

highly recommend that you purchase replacement tube sets from

conrad-johnson design. We anticipate tube life to accommodate

two to three years of operation without degradation in normal use -

if the preamplifier is switched off when not in use. If the preampli-

fier is left on at all times, tube life can be exhausted in a matter of a

few months.

Inhaltsverzeichnis

Andere Conrad-johnson design Verstärker Handbücher

Conrad-johnson design

Conrad-johnson design MV45A Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design CT5 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design PV 7 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design MOTIF MS1001 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design MF2550 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design Classic Sixty Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design Premier Ten Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design PREMIER THREE Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design LP125M Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design Premier 140 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design PREMIER SEVEN Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design Sonographe SA120 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design MV60 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design MV52 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design Evolution 20 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design PREMIER SIX Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design MOTIF MC9 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design One-b Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design MV50 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design MV125 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design CAV45 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design Sonographe SC-1 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design PV4 Bedienungsanleitung

Conrad-johnson design

Conrad-johnson design Motif MS2001 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung