Conrad-Johnson PV11 Bedienungsanleitung

Congratulations on your purchase of the conrad-johnson model PV11

vacuum tube preamplifier. In it, you have acquired one of the finest

pieces of music reproduction equipment available today. It is the result

of more than a decade of research by conrad-johnson design into the

application of vacuum tube devices to the reproduction of recorded

music.

The PV11 was designed to provide audiophiles with a reference quality

preamplifier capable of accurately reproducing the dynamics, tonalities

and textures of a live musical performance. The design and materials

have been carefully selected to yield years of unvarying excellence.

The PV11 is available as a complete phono-preamplifier and control unit

or as the PV11L line stage preamplifier/control unit only.

Please take a few minutes to read this manual so that you will better

understand the features and capabilities of your PV11. NOTE THAT

THE PV11 LINE STAGE IS PHASE INVERTING. See the section

entitled "Getting the most from your PV11" for details on correct hookup

to your system.

PV11 and PV11L Owner’s Manual 1

LIMITED WARRANTY FOR THE conrad-johnson

PV11/PV11L

1. conrad-johnson design, inc. warrants that the conrad-johnson

PV11/PV11L will be free of defects in materials and workmanship for a

period of three years from the date of original purchase.

2. During the warranty period, conrad-johnson will repair defective

units without charge for labor or parts (with the exception of the vacuum

tubes) subject to the following conditions:

a) The unit must not have been altered or damaged through

misuse, abuse, negligence, accident, or improper operation.

b) The purchaser must provide evidence of purchase at the time

service is requested.

c) All repairs must be undertaken at the factory or other service

center designated by conrad-johnson design, inc. Units submitted

for warranty repair must be shipped in the factory packing carton to

conrad-johnson design or its designated service center, freight and

insurance prepaid by the owner, and will be returned to the owner,

freight and insurance prepaid by conrad-johnson design. Cartons

are available from the factory for a nominal charge.

d) Normal wear and maintenance are not covered by this warranty.

3.The warranty may be transferred to subsequent owners provided that

the warranty registration card has been returned to conrad-johnson

design, inc. within 30 days of the original purchase and that the regis-

tered owner provides the factory with a signed notice giving the new

owner’snameandaddressandthemodelandserialnumberoftheunit.

4.Where permitted by law, conrad-johnson design’s liability shall be

limited to that set forth in this warranty. No other warranty of any kind,

expressed or implied, is made by conrad- johnson design, inc., and all

implied warranties, including merchantability and fitness for a particular

"purpose", which exceed the obligations and time limits set forth herein

are hereby disclaimed. Conrad-Johnson Design, Inc. shall not be liable

for incidental or consequential damages. Some states do not allow the

exclusion or limitation of incidental or consequential damages, or limita-

tions on how long an implied warranty lasts, so the above limitations or

exclusions may not apply to you.

PV11 and PV11L Owner’s Manual 2

5.This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state. Questions about warranty

service should be addressed to:

Service Department

conrad-johnson design, inc.

2733 Merrilee Drive

Fairfax, VA 22031

REGISTERING THE WARRANTY

Please return the enclosed card to the factory within 30 days of pur-

chasetoregisterthewarranty.Thewarrantymaybetransferredtoanew

owner if it has been properly registered initially and if the registered

owner sends a signed notice providing the name and address of the

new owner and the model and serial number of the unit.

Proper registration of the warranty is important! Not only will it preserve

transferability of your warranty, it will also enable us to inform you of any

alterations in the design of a given model and of any new products we

offer which are likely to be of interest to you.

PV11 and PV11L Owner’s Manual 3

INSTALLATION

Because of the number and type of vacuum tubes used, the PV11

dissipates a significant amount of heat (approximately 35 watts). It is

essential, therefore, that proper attention be paid to ventilation. The unit

should be mounted horizontally on a flat hard surface so that the

ventilation holes in the bottom are unobstructed. At least three inches of

clearance should be provided above the unit and the cabinet or shelf

should be open at the back. Vertical installation is not recommended.

To minimize hum pickup, keep the unit well away from the power

amplifier, and route power cords away from input cables.

The PV11 requires an ac power line providing between 108 and 125

volts at 50 to 60 Hz. Alternatively, the PV11 can be reconnected inter-

nally for operation on 220 volt power lines. Consult your dealer for

details about the conversion.

CONNECTION

Aux/ph: On a PV11L, this is an additional line-level input, and is

identical to the other inputs. On a PV11 with phono stage, this input

provides the amplification and equalization required by moving magnet

and high output moving coil cartridges. The phono input impedance is

the industry standard 47,000 ohms shunted by approximately 100 pico-

farads capacitance. This is well suited to nearly all moving magnet and

many high-output moving coil cartridges. If necessary, the input imped-

ance can be lowered by soldering a resistor across (from center pin to

ground) the input jack. To achieve a desired input resistance of RD, use

the following formula to compute the required additional resistance RA:

RA = 47000*RD/(47000-RD)

Some moving magnet cartridges require higher capacitance for opti-

mum performance. Increasing the input capacitance may be achieved

by soldering a suitable value capacitor across the phono input jack. Use

polystyrene capacitors for this purpose.

Tuner, cd, tape 1, tape 2: These are high level inputs and are electri-

cally equivalent. They present a 50k ohm load to the source. The

PV11 and PV11L Owner’s Manual 4

outputs of your tape recorders should be connected to tape 1 and tape

Record output: The two pairs of record outputs connect the selected

signal to your recorders or external processing loop (eg. equalizer). The

output signal is not affected by the level control. Connect "record out" to

the inputs of your tape recorders or external processors.

Output 1, Output 2: Connect this output to the input of your amplifier

(or crossover in a bi-amped system). We recommend the use of an

amplifierwithaninputimpedanceof10kohmsorhigher.SincethePV11

inverts phase, it may be necessary to invert the speaker leads to

maintain correct phase. See the section on "Getting the most out of your

PV11" for an explanation of this.

USE OF EXTERNAL TONE CONTROLS OR OTHER

EXTERNAL SIGNAL PROCESSING DEVICES:

Use Tape 1 and Record 1 for your tape recorder. Connect the output of

the tone controls to Tape 2 and the input of the tone controls to Record

2. The Monitor 2 position of the monitor switch will insert the tone

controls in the circuit; the Source position will provide flat, unprocessed

response.Thismethod of connectionwillpermit the useoftonecontrols

with tape playback by selecting Tape 1 in conjunction with Monitor 2.

AC OUTLETS

Four AC outlets are provided for your convenience: two, marked un-

switched, are always live; the remaining two are switched by the

preamp’s power switch. THE TOTAL CURRENT REQUIRED OF THE

SWITCHED OUTLETS MUST NOT EXCEED 5 AMPERES. This pre-

cludes the use of these outlets for high powered amplifiers. It is prefer-

able not to switch power amplifiers by the preamplifier power switch in

any case.

PV11 and PV11L Owner’s Manual 5

CONTROLS

OFF, POWER: Because of the delayed warmup characteristics of vac-

uum tube equipment, a time delay muting circcuit is incorporated in this

preamplifier. Output 1 and output 2 are grounded via a relay for approxi-

mately 90 seconds after the unit is turned on in order to suppress

warm-up transient noises. The relay grounds the outputs again immedi-

ately at turn off or in the event of any power line interruption.

SELECTOR: AUX/PH, TUNER, CD, TAPE 1, TAPE 2. This selector

switch is used to choose an input. The selected source will be available

at the source position of the tape monitor switch and at both record

outputs. Note that each tape deck’s output is fed back to its own record

input - CARE MUST BE TAKEN NOT TO SELECT TAPE 1 OR TAPE 2

WHILE THE TAPE DECK IN QUESTION IS IN RECORD MODE.

Similarly, if tape loop 1 is used for an external signal processor, Tape 1

should never be selected (and, of course, there is no reason to select it

since the external processor is not itself a program source). Failure to

observe these precautions will create an unstable feedback system and

may generate a "howling" sound.

TAPE 1, TAPE 2, SOURCE, MONITOR. Tape monitoring is accom-

plished via two pushbutton controls. The first, labeled Tape1/Tape 2

selects the tape deck from which you will be monitoring. The second,

labeled Source/Monitor lets you compare the original program source

with the playback from the chosen tape deck. These controls permit the

user to listen to a tape from one deck while recording material from

Phono, Tuner or CD inputs on a second tape deck.

MODE:LEFT, RIGHT, STEREO,REV, MONO.Thesetting of this switch

does not alter the signal at the record outputs except in the mono

position.

Left-Passes the left channel input to both channel outputs.

Right-Passes the right channel input to both channel outputs.

Stereo-Normal stereo operation.

Reverse-Passes the left channel input to right channel output and

vice-versa.

Mono-Passes the sum of left and right inputs to both channel

outputs. This position produces a near mono signal at the record

outputs.

PV11 and PV11L Owner’s Manual 6

BALANCE: This control is an eleven position stepped attenuator, ad-

justing the channel balance in approximately .75 dB steps. The maxi-

mum attenuation is under 4 dB, so both channels will be present even

in the extreme positions. In normal use the control will be centered.

LEVEL: The PV11 volume control is an extremely precise control, main

taining channel to channel accuracy to within 1/2 dB throughout its

rotation.

VACUUM TUBE REPLACEMENT

The audio circuit of the PV11 uses six vacuum tubes of three different

types: two 12AX7 (V1 and V2), one 5751 (V3) and three 12AU7 (V4, V5

and V6). The PV11L uses two type 12AU7 (V5 and V6). Each type has

been carefully chosen for its circuit application. It is well known that

tubes of a given type vary sonically depending on the manufacturer. We

have chosen the brands of tubes we supply based on extensive audi-

tioning of available brands. The choice of brands has been made solely

on the basis of sonic performance without regard for either cost or

prestige. We know of no vacuum tubes available which will improve the

sonic performance of your PV11. Also, the tubes in your preamplifier

have been tempered by a controlled burn in procedure that permits

them to perform for a greatly extended period with out sonic degrada-

tion. We anticipate two or three years of operation without degradation

in normal use. We highly recommend that when the time comes to

replace the vacuum tubes you purchase replacement tube sets from

conrad-johnson design.

Consult the tube location diagram on the next page when replacing

tubes.

Pleasenote:The indiscriminate substitution of type12AX7tubesforthe

5751 will seriously degrade the sonic performance of the unit.

PV11 and PV11L Owner’s Manual 7

PV11 Tube Complement

V1 AND V2 type 12AX7

V3 type 5751

V4 - V6 type 12AU7

NOTE: PV11L uses only tubes V5 and V6

V1 V2

V5 V6

PV11 and PV11L Owner’s Manual 8

GETTING THE MOST FROM YOUR PV11

The conrad-johnson PV11 offers an unparalleled level of sophistication

and refinement in music reproduction, but it cannot transform an inferior

stereo system. Only high quality amplifiers and loudspeaker systems

will be capable of fully revealing the capabilities of this precision instru-

ment.

Given a system of high quality components, there remain a number of

important details which must be attended to.

ABSOLUTE PHASE

Musical notes are heard through the ear’s response to waves of alter-

nating rise and fall of air pressure. Musical transients are exclusively

positive: that is, the initial effect is a rise in pressure. The ear is capable

of distinguishing these positive transients from the musically unnatural

alternative of a negative transient (an initial fall in air pressure). In terms

of your stereo system, these transients are created by your loudspeak-

ers. If the speakers respond to musical transients by first moving out,

they are creating a rise in pressure, and the system is said to be "phase

correct". If they respond by moving in, they create a fall in pressure and

the system is said to be phase inverting. Each component in the stereo

system is either phase correct or phase inverting (including the source

and speakers-these are normally phase correct). It is of no conse-

quence if an individual component is phase inverting, as long as the

system as a whole is phase correct. This will be the case as long as the

number of phase inversions is even (or zero).

THE LINE STAGE OF THE PV11 INVERTS PHASE OF ALL INPUTS

(including phono). If your system has an odd number of inversions, then

youmustaddone phaseinversion. THISIS CONVENIENTLYDONE BY

REVERSING THE POSITIVE AND NEGATIVE CONNECTIONS TO

YOUR SPEAKERS (be sure to reverse both channels).

If you are not sure about the phase of every piece in your system, you

can establish correct absolute phase by careful listening. When the

system is in correct phase, transients will be noticeably cleaner and

more sharply defined. The effect is especially apparent on plucked

string sounds. A final warning-not all recordings are phase correct

PV11 and PV11L Owner’s Manual 9

(including some "audiophile" recordings), so listen to several before

concluding your investigation of absolute phase.

AC LINE POLARITY

Each piece of electronic equipment in your system is subject to minute

ac leakage currents to the chassis. Since the chassis of components in

a system are usually connected via the ground side of the interconnect

wires,theseleakagecurrents aresuper imposedon themusical signals.

It is possible to minimize these current flows by carefully selecting the

way in which each component is plugged into the wall outlet. Because

the power cord on the PV11 is not polarized, it can be plugged in two

ways. It will normally sound better in one orientation than in the other.

The same will be true of any electronic device in your system.

THE IMPORTANCE OF WIRES

Interconnect and speaker wires are an important element in your stereo

system. Interconnects are available which will permit a reference quality

system to blossom and fulfill its promise of musical reality. Others will

strangle the system to the point where it becomes no better than

average. To complicate matters, our experience suggests that the

choiceof interconnects will be system dependent- those that are ranked

first on a given system may be a poor choice for a different system.

Consult your conrad-johnson dealer for recommendations for your spe-

cific system.

TIP

Warm up the PV11 before listening: The sonic performance of the PV11

improvesnoticeablyastheunitwarmsup.Themidrangebecomesmore

lucid, the highs smoother, and the soundstage expands. Most of the

improvement will occur in the first half hour of warm up.

Questions: If you have questions about the installation or function of

your PV11 do not hesitate to call Customer Service at (703) 698-8581.

PV11 and PV11L Owner’s Manual 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Conrad-Johnson Verstärker Handbücher

Conrad-Johnson

Conrad-Johnson ET7 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson MF2100 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson PV10A Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson Sonographe SA250 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson ET5 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson PV8 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson Premier 18LS Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson MET1 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson MV60SE Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson TEA2 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson MV45 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson PV14L Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson PV-3 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson 16LS Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson ART 27A Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson ART 150 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson CAV50 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson LP275M Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson MF200 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson LP140M Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson MV100 Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson Premier Four Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson LP260M Bedienungsanleitung

Conrad-Johnson

Conrad-Johnson Classic 2 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung