Cooper Lighting Halo Power Trac L630 2C 2N Bedienungsanleitung

HALO L630 2C 2N POWER TRAC INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

When installing or using this track system, basic safety precautions

should always be followed, including the following:

1. Read all of these instructions before installing the track system.

2. Save these instructions and refer to them when additions to or

changes in the track configuration are made.

3. Do not install this track in damp or wet locations.

4. Do not install any part of a track system less than 5 feet above the

floor.

5. Do not install any fixture assembly closer than 6 inches from any cur-

tain or similar combustible material.

6. Disconnect electrical power before adding to or changing the config-

uration of the track.

7. Do not attempt to energize anything other than track lighting fixtures

on the track. To reduce the risk of fire and electric shock, do not

attempt to connect power tools, extension cords, appliances and the

like to the track.

8. CAUTION: This track system is not intended for use with power sup-

ply cord or convenience receptacle adapter.

9CAUTION: To reduce the risk of fire and electric shock, use only fix-

ture assemblies marked for use with Halo track and track fittings

marked for use with L630 Series track.

10. The track system is to be supplied by one or two 480V/277V 60Hz

single phase 3-wire system with a grounded neutral.

11. The mounting clips, screws or stems are to be mounted in pre-drilled

holes as follows:

4’ Track - two places - one at each end of track

8’ Track - Three places - one in the center and each end of the track

12’ Track - four places - one at each end of track and 4 feet from

each end

If track requires field cutting, refer to field cutting instructions

12. CAUTION: The maximum capacity of L630 Track is 40A per circuit.

When installing, do not exceed the capacity of your circuits. Check

fuses and circuits carefully before installing.

SAVE THESE INSTRUCTIONS

Cooper Lighting • 1121 Highway 74 South • Peachtree City GA 30269 • 770-468-4800

703113

OUTLET

BOX

COVER

LIVE END

CONNECTOR

OUTLET

BOX

COVER

SCREW

MOUNTING

SCREWS

INSTALLATION OF TRACK TO AN OUTLET BOX

Step 1. Punch out proper knockout holes in ceiling plate for mounting to out-

let box and to live end fitting (note that special smooth plastic finish

piece on metal ceiling plate requires caution in deterring location of

proper knockout before making holes). Remove flat head screw)s)

from back of live end fitting and use to fasten plate to fitting.

Step 2. Remove cover from live end fitting. Place track with ceiling plate

attached over outlet box and mark on ceiling or wall the position of

the track mounting holes.

Step 3. Drill mounting holes large enough for toggles and install track with fur-

nished toggle bolts. If track is to be mounted on a solid surface, use

#8 screws (not supplied) instead of toggle bolts.

Step 4. Fasten ceiling plate to outlet box with two screws. Pull wires from box

through open hole in live end as shown.

Step 5. Cut and strip wires from box and fasten to screw terminals in live end

fitting (see detail). Push excess wire back into outlet box.

Step 6. Replace cover on live end and tighten screw.

GREEN

GROUND

SCREW

LINENEUTRAL

TIGHTEN SCREW

AFTER INSERTING

IN TRACK

TRACK

Figure 1

Cooper Lighting • 1121 Highway 74 South • Peachtree City GA 30269 • 770-468-4800

703113

NOTE: Cutting should be done preferably from the dead end of the

track.

Step 1. Remove dead end fitting and pull copper bus bars and insula-

tors flush or even with one end of the track.

Step 2. With hacksaw, cut the flush end (the side with insulators and

bus bars even to end) to desired length. Be sure to allow 1/8”

for dead end fitting which must be reinstalled to the track end.

Step 3. Remove all burrs from the track, insulators and copper bus

bars.

Step 4. Push copper bus bars back into the insulators 3/8” from the

end of the insulators.

NOTE: After you complete Step 4, bus bar insulators should be

a minimum of 3/8” and a maximum of 1/2” from each end of the

insulator. If this is not the case, make appropriate modifications.

Step 5. Reinstall the dead end and/or appropriate feed connector and

tighten the screw.

CAUTION: After track has been field cut, make certain that

each length of track that is 4 feet or less in length has one

mounting opening spaced a maximum of 6 inches from each

track end section. A single section of track that is greater than 4

feet in length must have mounting openings a maximum of 12

inches from each end of the track with additional openings a

minimum of every 4 feet long the length of the track section.

Additional openings may be provided as needed.

If additional mounting holes are required, follow this procedure:

Step 1. Locate desired mounting hole(s) on the inside of the

track section along the center line.

Step 2. Using 3/16” diameter drill bit, drill hole through the

track channel.

Caution: Take care that you do not damage the bus bar

insulators during the drilling operation. If you

accidentally damage any insulators, discard the track

section. DO NOT ATTEMPT TO USE IT IN THE

INSTALLATION.

Step 3. Remove all burrs and install track as described

above.

FIELD CUTTING TRACK TO SPECIAL LENGTHS

NOTE: The T and X Connectors wiring patterns can be easily changed in the field by shifting jumping positions or eliminating wires. Several circuits

can be fed through any connector by removing two or more of the jumper wires and replacing them with feed wires. Separate instruction

sheets are packed with each connector.

Additional Connectors Available

L673 Straight connector for

straight runs.

L674 “L” connector for right

or left turns. L675 “T” Connector for 3 leg

arrangements.

L676 X Connector for 4 leg

arrangements.

DEAD END FITTING

TO REMOVE, LOOSEN

SCREW AND SLIDE FIT-

TING OUT

REDRILL MOUNTING

HOLE(S) IF NECESSARY

NEW CUT MUST BE

AT EXACT RIGHT

ANGLE (90°)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cooper Lighting Inneneinrichtung Handbücher

Cooper Lighting

Cooper Lighting PORTFOLIO QD19 Bedienungsanleitung

Cooper Lighting

Cooper Lighting MCGRAW-EDISO 1197 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1742 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux 2HB65 Bedienungsanleitung

Cooper Lighting

Cooper Lighting PM123ob Bedienungsanleitung

Cooper Lighting

Cooper Lighting IRiS E5P30 Bedienungsanleitung

Cooper Lighting

Cooper Lighting METALUX 2HB35 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Stealth Graze Fixture Mounting V90181 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux M Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting 1484 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 601 SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting 228T5 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HTS M1 E1 Z1 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux BI Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fenestra 142 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Quantum Series CQA Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE Harmony Bedienungsanleitung

Cooper Lighting

Cooper Lighting 641 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 603 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HC-HE Bedienungsanleitung

Cooper Lighting

Cooper Lighting Neo-Ray's 22DIW Bedienungsanleitung

Cooper Lighting

Cooper Lighting Portfolio M8605 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 499-RP-TR Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites LPX Series Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung