Cooper Lighting IMI-682 Bedienungsanleitung

Tools Required Socket, 5/16" Socket, 3/4" Deep Well Socket, Electrical

wiring tools.

NOTE: These luminaires are designed for outdoor lighting services, and

should not be used in area of limited ventilation or in high ambient

temperature enclosures. Construction is suitable for down lighting only.

Best results will be obtained if installed and maintained according to the

following recommendations.

1. With the fixture on its back, open and remove door by pressing thumb

latches outward at the same time, open the door and lift it from the

hinges. FIG. 1

2. Run the two (2) threaded rods through the center of the semi-enclosed

hole details in the arm extrusion. To help orient the arm correctly with

the housing, please note that one end of the extruded arm has an angled

cut and the other has a perpendicular cut with two (2) drain notches

located on the bottom. If assembling to a round pole, use the round pole

adapter with the drain channels located at the extruded arm end with

the drain slots. Mate the angled side of the extruded arm to the housing

so that the bottom surface of the extrusion is parallel to the bottom of

the fixture, and the drain notches are facing down and located away

from the housing. FIG. 2 Slide the threaded rods into the interior of the

housing. Attach flat washer, lock washer, and nut into place in the order

shown in FIG. 2. Torque hex nuts to 450 lb/in.

3. If necessary, remove the cap on the pole. Position the housing and arm

to assemble it to the pole. Lower the nut plate into the interior of the

pole as shown. Slide the threaded rods through the pole and thread into

the nut plate until the rod protrudes though the nut plate slightly. Tighten

both nuts located inside of the housing to 30 lb/ft of torque.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency

during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest

representative.

Talon Large

Sheet 1 of 3

11/29/07 IMI-682

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly. Tighten all fixture components

to their recommended torque values.

WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture.

Install right side up.

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH071365

FIG. 1

Latches

FIG. 2

Nut Plate

Fits Inside

Of Pole Round Pole Adapter (Optional)

Arm

Hardware: Washer,

Lock Washer, And

Hex Nut

Mounting Rod (2)

4. With the pole and fixture(s) raised into position, place the power tray

onto the hinges of the housing electrical compartment and let it hang

free. Locate the power connector plug and rotate the power tray until the

connection can be made with the mating connector in the housing. Raise

the power tray until the two (2) thumbscrews engage and tighten until

fully snug. FIG. 3

5. Replace door on the hinges at the rear of the housing, rotate into

position, and assure that both latches are fastened securely.

FIXTURE MAINTENANCE

RELAMPING

1. Disengage both latches and open the door. Do not let the door swing

freely on the hinges.

2. Replace the lamp with the appropriate type and wattage and reassemble

the refractor to the upper housing. FIG. 4

3. Close the door and assure that the latches are securely fastened.

NEMA PHOTOCONTROL REPLACEMENT

1. The photocontrol is mounted on top the housing. FIG. 5

2. Remove the photocontrol by twisting counterclockwise and replace.

PLUG-IN STARTER REPLACEMENT

1. This procedure applies to fixtures with a plug-in type starter. Disengage

both latches and open the door. Do not let the door swing freely on the

hinges. Loosen the power tray thumbscrews, unplug the power

connector as you lower the powertray, and continue lowering until the

powertray hangs free on the hinges. The starter is located in the position

shown. Remove and replace. Reverse the directions to secure the

powertray and the door after starter replacement.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency

during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest

representative.

Talon Large

Sheet 2 of 3

11/29/07 IMI-682

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly. Tighten all fixture components

to their recommended torque values.

WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture.

Install right side up.

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH071365

FIG. 4

Latches

Lamp

Removable Powertray

Lift And Hang On Hinges

Removable Door

Lift And Hang

Door On Hinges

FIG. 3

PowerTray

Thumbscrews (2)

FIG. 5

NEMATwistlock

Photocontrol

2. Remove the plug-in starter from the receptacle and replace.

FIG. 6

3. Assure that the thumbscrews on the powertray and both latches

on the door are fastened securely.

OPTIC DISTRIBUTION AND ORIENTATION

The Talon Large fixture is offered with some optics that have

directional distributions. For aiming purposes, the Talon Large was

designed with the flexibility to allow each of its optics to be rotated

to any of four (4) positions, located at 90° increments. There are

two (2) mounting configurations that are used to mount all of the

Talon Large optics. The horizontally-lamped optics (as well as the

Type 4 vertical optic) use the horizontal optics adapter. All vertically

lamped optics use the vertical mount adapter.

1. Vertical Optics: Open the door and remove the lamp. Use a

screwdriver to slightly loosen (do not remove) the four (4) screws

as shown in FIG. 7. The optic has four (4) keyhole details that

allow it to release by turning the reflector clockwise a few

degrees allowing the optic to be removed. Reposition the optic

and tighten the screws securely.

2. Horizontal Optics: (this also covers the Type 4 vertical optic).

Open the door and remove the lamp. Use a screwdriver to

remove the four (4) screws as shown in FIG. 8. Reposition the

optic and reinsert the screws securely.

These instructions do not claim to cover all details or variations in

the equipment, procedure, or process described, nor to provide

directions for meeting every possible contingency during

installation, operation or maintenance. When additional information

is desired to satisfy a problem not covered sufficiently for user's

purpose, please contact your nearest representative.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency

during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest

representative.

Talon Large

Sheet 3 of 3

11/29/07 IMI-682

INSTALLATION INSTRUCTIONS

IMPORTANT: READ CAREFULLY BEFORE INSTALLING FIXTURE.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.

WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly. Tighten all fixture components

to their recommended torque values.

WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture.

Install right side up.

NOTE: Specifications and dimensions subject to change without notice.

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH071365

FIG. 8

Remove Optic, Rotate

To Desired Position

And Fasten Into Place

FIG. 6

Plug-In Starter

Thumbscrews

FIG. 7

Remove Optic, Rotate

To Desired Position

And Fasten Into Place

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cooper Lighting Inneneinrichtung Handbücher

Cooper Lighting

Cooper Lighting LV2060ISMulti-Lamp Luminaire LV2060IS Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE FDI Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere Cambria 212 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 210-D Bedienungsanleitung

Cooper Lighting

Cooper Lighting Portfolio 885 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Super-Lites XR Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 601V-24 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 603 Bedienungsanleitung

Cooper Lighting

Cooper Lighting New-Ray 739 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1730 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites CAX Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting 698 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting LUMIERE BOCA 602 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux GR5 SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux M Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting IRiS E5P30 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 1483 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Visor and Non-Visor ADY071473 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 642-A Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sedona 1800-24 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fail-Safe SCH24 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1735 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux 2EP3GAX Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting PM115obi Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung