Cooper Lighting IMI-694 Bedienungsanleitung

FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR

DEATH

NOTE : Use minimum 90°C supply wire rating for connections in J-box.

Fixture Orientation Guideline:

Proper orientation of luminaire may vary based upon design requirements

specified per given application. Labels are supplied on top of fixture and

mounting plate for reference to proper fixture alignment. Align quick mount

plate in correct direction by referencing number of fixtures required (double or

single row luminaire installation) to direction of arrows. Direction of arrow(s)

should be in line with direction of traffic.

LUMINAIRE INSTALLATION:

1. Install quick mount plate on a 4” junction box as shown in (Figure 1).

Note the required position of plate to ensure correct light beam

orientation from fixture. See guidelines above or labels on top of fixture

housing and mounting plate if applicable.

2. Secure hanging hook into the rear hooks of quick mount plate

(Figure 2 & 3).

3. Make wiring connection while luminaire is being suspended from hanging

hook.

4. Push excess wires and connectors up into the junction box through center

access hole.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,

operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

EPL Envoy

Parking Luminaire

Sheet 1 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

GENERAL: Upon receipt of luminaire thoroughly inspect for any freight

damage, which should be brought to the attention of the delivery

carrier. Compare the catalog description listed on the packing slip

with the luminaire label on the housing to assure you have received the

correct merchandise.

SAFETY: This luminaire must be wired in accordance with the national

electrical code and applicable codes and ordinances. Proper grounding

is required to insure personal safety. Carefully observe grounding

procedure. All work should be done by a qualified electrician.

WARNING: Make certain power is OFF before starting installation or

attempting any maintenance.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit

breaker before installing or servicing.

WARNING: Risk of Burn. Disconnect power and allow luminaire to cool

before changing lamp or handling luminaire.

WARNING: This luminaire is for use with downlight applications only.

WARNING: RISK OF FIRE! DO NOT mount on or near combustible

materials.

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH080771

Figure 3

Figure 1

Figure 2

CENTER ACCESS

HOLE

#8-32 SCREW

QUICK MOUNT

PLATE

J-BOX

HANGING

HOOK

LUMINAIRE

LIFT UP

THEN PUSH

LUMINAIRE

BACK

FRONT HOOKS

LUMINAIRE

HANGING HOOK

REAR HOOKS

QUICK MOUNT

PLATE

J-BOX

5. Lift up luminaire onto the (4) four hooks of quick mount plate while guiding

the wires through center access hole (Figure 3).

6. Push luminaire forward for engagement (Figure 3). When it reaches the

full-engaged position, a “CLICK” can be heard.

CAUTION: If full engagement is not reached, it is not yet rigidly installed.

REMOVAL OF LUMINAIRE:

WARNING: Make sure the power to the unit is OFF and allow it to cool.

1. Note: Remove tamper proof screws first if luminaire includes (TR)

tamper-resistant option (Figure 4).

2. To release clasp lock on “quick mount” bracket, push handle inward and

pull luminaire forward (Figure 5).

CAUTION: Do not let luminaire fall. Support luminaire while lowering off of

j-box to resting, hanging position.

3. Remove hanging hook from quick mount plate (Figure 2 & 3).

CAUTION: Support luminaire while removing.

4. For re-installation of luminaire, refer to steps 1 through 6 on Luminaire

Installation.

EPL Envoy

Parking Luminaire

Sheet 2 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH080771

operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 5

TO REMOVE

Figure 4

TAMPER-PROOF

SCREW FOR HANDLE

TAMPER-PROOF

SCREW FOR LATCH

HANDLE

PUSH

PULL

LAMP INSTALLATION: :

1. To install the lamp, unlatch both latches (Figure 6). Note: Remove tamper

proof screws first if luminaire includes (TR) tamper-resistant option (Figure

4).

2. Allow lens to swing open (Figure 7). Lens will remain captive.

CAUTION: Support lens while it swings open.

3. Install lamp securely into socket. CAUTION: Verify that lamp source and

wattage correspond with the luminaire label.

4. To close the luminaire, rotate lens back up to position. Lift up the lens and

align with (4) ribs of top lens on both sides(Figure 8).

CAUTION: Latching luminaire closed prior to having proper alignment will

result in lens breakage.

5. Push one side of the latch up to grasp edge of lens and then push inward to

complete latching (Figure 9 & 10). Repeat for the other latch.

EPL Envoy

Parking Luminaire

Sheet 3 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH080771

operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 6

Figure 7

Figure 8

Figure 9

Figure 10

PULL TO

UNLATCH

PULL TO

UNLATCH

LAMP

SUPPORT LENS

WHILE IT SWINGS

OPEN

ALIGN THESE RIBS AS

SHOWN BEFORE LATCHING

(OTHER SIDE NOT SHOWN)

LATCH

LENS

LATCH UP TO

GRASP EDGE

OF LENS BEFORE

LATCHING

PUSH TO

LATCH

PUSH TO

LATCH

TRUNNION MOUNT INSTALLATION: (Figure 11)

Note: Use minimum 90°C supply wire when installed per below procedure

and connections are made inside of condulet body.

Note: For 8-3/8” to 13-1/4” vertical adjustment (Up or Down only).

1. Install top trunnion on the ceiling using masonry anchors (provided by

others).

2. Apply sealing compound (by others) on one end of ½” nipple.

3. Screw nipple into the housing.

4. Install bottom trunnion L-brackets on the top plate (with provided #10-24

pan head screws, lock washers and nuts—Torque between 24-27 in-lb).

5. Install top plate on the housing (with provided #10-24 flat head screws—

Torque between 24-27 in-lb).

6. Pull wires from back of luminaire through nipple to make for easy routing

into condulet body.

7. Apply sealing compound to top of nipple. Screw condulet body onto nipple.

8. Install bottom trunnion L-brackets to the top trunnion (with provided 3/8"

bolts, lock washers and nuts—Torque between 17-20 ft-lb).

9. Route conduit and power supply wires to condulet body.

10. Make connections. Push excess wires and connectors back into the

condulet body.

11. Install gasket and cover.

TASK LIGHT INSTALLATION: (Figure 12)

WARNING: RISK OF FIRE! DO NOT mount on or near combustible materials.

1. Apply sealing compound on the threads of handle (provided by others).

2. Screws handle into adapter.

3. Aim handle to a preferred position and lock it in position.

4. Aim task light head to a preferred position and tighten #10-24 Allen head

screw (with provided Allen wrench).

5. Pull wires through access and restrain with wire tie.

Note: Depending on which task light option is being ordered, additional

wiring/routing will be necessary. Reference wiring diagrams shipped with

task light.

EPL Envoy

Parking Luminaire

Sheet 4 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH080771

operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 12

Figure 11

#10-24

ALLEN HEAD

LOCK NUT

ADAPTER

HANDLE

(APPLY SEALING

COMPOUND BY OTHERS)

TASK LIGHT

HEAD

FOR VERTICAL ADJUSTMENT (UP OR DOWN ONLY)

8-3/8 TO 13-1/4” FROM TOP OF LUMINAIRE

CONDULET

BODY

TOP

TRUNNION

TOP PLATE

NIPPLE

APPLY SEALING

COMPOUND

(BY OTHERS)

#10-24

SCREW

HOUSING

BOTTOM

TRUNNION

#10-24 FLAT

CS SCREW

GASKET

COVER

3/8” BOLT

THRU-BRANCH WIRING INSTALLATION: (Figure 13 & 14)

NOTE : Use 90°C wire rating for luminaire with thru-branch option for

fixtures 100w or below at 25°C ambient temperature applications.

: Use 105°C wire rating for luminaire with thru-branch option for

150w to 175w at 25°C ambient temperature applications

: Use 125°C wire rating for luminaire with thru-branch option for

200w at 25°C ambient temperature applications.

: Use 150°C wire rating for luminaire with thru-branch option for all

fixtures at 40°C ambient temperature applications.

WARNING: RISK OF FIRE! DO NOT mount on or near combustible materials.

Note: Requires luminaire option (CT) =Conduit Tap-(2) ¾” NPSM taps and

plugs.

1. Remove lens and housing cover from luminaire.

2. Remove conduit plugs.

3. Affix luminaire to the ceiling with anchors through cast in knock outs

(anchors provided by others). Use RTV or other liquid sealant around

perimeter of KO’s.

4. Apply sealing compound to end of pipe if applicable. Install conduit pipe.

5. Route wires inside the housing as shown and use wire ties and screws to

restrain in position.

CAUTION: Use wire ties/self-tapping screws to restrain wires from

contacting ballast (provided by others).

EPL Envoy

Parking Luminaire

Sheet 5 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH080771

operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 13

Figure 14

#10-24 X 5/8 TAPTITE

SCREW (BY OTHERS)

WIRE TIE

(BY OTHERS)

KNOCK-OUT

FEATURE

THRU-BRANCH

FEATURE

CONDUIT

PIPE

KNOCK-OUT

FEATURE

KNOCK-OUT

FEATURE

WIRE TIE

(BY OTHERS)

KNOCK-OUT

FEATURE

KNOCK-OUT

FEATURE

KNOCK-OUT

FEATURE

KNOCK-OUT

FEATURE

KNOCK-OUT

FEATURE

CONDUIT

PIPE

THRU-BRANCH

FEATURE

WIRE TIE

(BY OTHERS)

#10-24 X 5/8 TAPTITE

SCREW (BY OTHERS)

WIRE TIE

(BY OTHERS)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cooper Lighting Inneneinrichtung Handbücher

Cooper Lighting

Cooper Lighting Shaper 699 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Poles P125S020 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 417SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting 226 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting METALUX 2HB35 Bedienungsanleitung

Cooper Lighting

Cooper Lighting IRIS E7A21 Bedienungsanleitung

Cooper Lighting

Cooper Lighting PORTFOLIO H77250QT4 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux 2P5GAX SERIES Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 494-S Bedienungsanleitung

Cooper Lighting

Cooper Lighting Paralux III EP3GAX Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Portfolio M8605 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 624 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting 196HO Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites EUR Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shallow Downlight Metal Halide ED17 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 80-IW Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere 1070 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 271 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting 1499 Bedienungsanleitung

Cooper Lighting

Cooper Lighting IMI-321 Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE FMS24LP Bedienungsanleitung

Cooper Lighting

Cooper Lighting 1484 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 850 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux 8I5355 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung