Cooper Lighting Streetworks SA6001-SA6002 Bedienungsanleitung

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

ARM INSTALLATION

Bishop Arm (SA6001-SA6002, SA6050-SA6051, SA6101-SA6102

& SA6150-SA6151)

See Figure 1.

1. Secure arm mount flush with wall using 3/8” hardware supplied

by others.

2. Remove wireway cover screws and wireway cover.

3. Mount arm to arm mount positioning service leads in wireway.

Insert and tighten four screws to 80 in/lbs.

4. Pull fixture leads through arm.

5. Align locating pin and socket when raising fixture to arm.

See Figure 2.

6. Insert and tighten 4 fixture screws with Teflon washers, provided

in polybag, to 80 in/lbs.

7. Connect fixture leads to service leads in wireway.

8. Resecure wireway cover with wireway cover screws tightened to

50 in/lbs.

Traditional Arm (SA6003-SA6004, SA6052-SA6053, SA6103-

SA6104 & SA6152-SA6153)

See Figure 3.

1. Secure arm mount flush with wall using 3/8” hardware supplied

by others.

2. Remove wireway cover screw and wireway cover.

3. Mount arm to arm mount positioning service leads in wireway.

Insert and tighten set screw to 80 in/lbs.

4. Pull fixture leads through arm.

5. Align locating pin and socket when raising fixture to arm.

See Figure 2.

6. Insert and tighten 4 fixture screws with Teflon washers, provided

in polybag, to 80 in/lbs.

7. Connect fixture leads to service leads in wireway.

8. Resecure wireway cover with wireway cover screw tightened to

50 in/lbs.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-658 ADW051684

Epic/Wall Mounted

Fixtures

Sheet 1 of 4

10/18/05 IMI-658

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

General: Upon receipt of fixture thoroughly inspect for any

freight damage, which should be brought to the attention of

the delivery carrier. Compare the catalog description listed

on the packing slip with the fixture label on the housing to

assure you have received the correct merchandise.

Safety: This fixture must be wired in accordance with

the national electrical code and applicable local codes

and ordinance. Proper grounding is required to insure

personal safety. Carefully observe grounding procedure

under installation section. All work should be done by a

qualified electrician.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Fixture Screws (4)

Fig. 1

Bishop Arm

Teflon Washer (4)

(4) 3/8-16 x 1-1/4

Button Head Cap

Screws

Backplate Med

Bishop Wall

Wireway Cover

(4) 3/8" Lag Bolts

(supplied by others)

Wireway Cover

Srews (2)

Aligning Pin

Aligning Socket

Fig. 2a

Modern Top

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-658 ADW051684

Epic/Wall Mounted

Fixtures

Sheet 2 of 4

10/18/05 IMI-658

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

FIXTURE MAINTENANCE

A. Relamping

Horizontally lamped

1. Loosen two door screws.

2. Lower door to tethered resting position. See Figure 4.

3. Install suitable lamp. Consult re-lamp label and lamp

instructions for details. Do not overtighten.

4. Raise door and secure with screws.

Vertically lamped

1. Loosen and remove ring retaining screws globe retaining

ring and globe. Components are not tethered.

See Figure 5. (closeup of lowered globe and ring)

2. Install suitable lamp. Consult re-lamp label and lamp

instructions for details. Do not overtighten.

3. Reinstall ring retaining screws securing globe retaining ring

and globe. In the case of type 3 refractive glass globe, use

the mark on globe bottom for orientation.

B. Starter and Fuse Replacement (Where applicable)

Horizontally lamped

1. Loosen two door screws.

2. Lower door to tethered resting position. See Figure 4.

3. Loosen thumbscrew until rectangular washer can be rotated

90 degrees. See Figure 6.

4. Rotate reflector faceplate to release from screws using key

hole slots.

5. Unplug optic quick-disconnect.

6. Remove two screws on ballast cover followed by ballast

cover. See Figure 7.

7. For starter replacement, remove the plug-in starter from

receptacle and replace.

For fuse replacement, unscrew fuse holder cap and replace

fuse. Resecure fuse holder cap.

8. Resecure the ballast cover with the two screws.

9. Plug optic quick-disconnect and secure reflector by keyhole

slots and thumbscrew.

10. Raise door and secure with screws.

Aligning Socket

Fig. 2b

Aligning Pin

Classical Top

Wireway Cover Screws

Fig. 3

Arm Mount

Fixture Screws

Teflon Washers

Wireway Cover

Mounting Hardware

(supplied by others)

Traditional Arm

Door Screws

Fig. 4a Options

Flat Lensor SagLens

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-658 ADW051684

Epic/Wall Mounted

Fixtures

Sheet 3 of 4

10/18/05 IMI-658

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Vertically lamped

1. Loosen and remove ring retaining screws globe retaining ring

and globe. Components are not tethered.

See Figure 5.

2. Remove two screws on ballast cover followed by ballast

cover. See Figure 7.

3. Unplug optic quick-disconnect.

4. For starter replacement, remove the plug-in starter from

receptacle and replace.

For fuse replacement, unscrew fuse holder cap and replace

fuse. Resecure fuse holder cap.

5. Plug optic quick-disconnect.

6. Resecure the ballast cover with the two screws.

7. Reinstall ring retaining screws securing globe retaining ring

and globe. In the case of type 3 refractive glass globe, use the

mark on globe bottom for orientation.

C. Power Pack Replacement

Horizontally lamped

1. Loosen two door screws.

2. Lower door to tethered resting position. See Figure 4.

3. Loosen thumbscrew until rectangular washer can be rotated

90 degrees. See Figure 6.

4. Rotate reflector faceplate to release from screws using key

hole slots.

5. Unplug optic quick-disconnect.

6. Remove two screws on ballast cover followed by ballast

cover. See Figure 7.

7. Unplug service quick-disconnect.

8. Holding the handle, loosen the two screws holding the power

pack to the fixture housing. See Figure 8.

9. Holding the handle, rotate the power pack until free and lower.

10. Holding replacement power pack by handle, raise onto screw

heads and rotate.

11. Tighten the two screws while holding power pack in position.

12. Plug together the service quick-disconnect.

13. Resecure the ballast cover with the two screws.

14. Reconnect optic quick-disconnect and secure reflector by

keyhole slots and thumbscrew.

15. Raise door and secure with screws.

Tether

Door Screws

Fig. 4b Options

Flat Lensor SagLens

Ring Retaining Screws

Fig. 5a

Globe Retaining Ring

Globe

Option MA

Ring Retaining Screws

Fig. 5b

Globe Retaining Ring

Globe

Options

3R & 5R

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible

contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please

contact your nearest representative.

Customer First Center • 1121 Hwy 74 South • Peachtree City, GA 30269 IMI-658 ADW051684

Epic/Wall Mounted

Fixtures

Sheet 4 of 4

10/18/05 IMI-658

INSTALLATION INSTRUCTIONS

IMPORTANT: Read carefully before installing fixture. Retain for future reference.

WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing

or servicing.

Vertically lamped

1. Loosen and remove ring retaining screws globe retaining

ring and globe. Components are not tethered.

See Figure 5.

2. Remove two screws on ballast cover followed by ballast

cover. See Figure 6.

3. Unplug optic quick-disconnect.

4. Unplug service quick-disconnect.

5. Loosen the two screws holding the power pack to the

fixture housing. See Figure 7.

6. Holding the power pack by the handle, rotate the power

pack until free and lower.

7. Holding replacement power pack by handle, raise onto

screw heads and rotate.

8. Tighten the two screws while holding power pack in

position.

9. Plug together the service quick-disconnect.

10. Plug together the optic quick-disconnect.

11. Resecure the ballast cover with the two screws.

12. Reinstall ring retaining screws securing globe retaining ring

and globe. In the case of type 3 refractive glass globe, use

the mark on globe bottom for orientation.

Keyhole Slot

Fig. 6

Rectangular Washer

Thumbscrew

Reflector

Removal

Ballast Cover

Screws

Optic

Quick-

Disconnect

Fig. 7a

Starter

Fig. 7b

Handle

Fuse

Service

Quick-Disconnect

Screws

Fig. 8

Power Pack Removal

Dieses Handbuch passt für folgende Modelle

Andere Cooper Lighting Inneneinrichtung Handbücher

Cooper Lighting

Cooper Lighting Sure-Lites ELX Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sedona 1800-24 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Triad 17-IW Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumark VL Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere 1048 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 271 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1631 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Sure-Lites Lifeway II C Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE FCT Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 643 Series Bedienungsanleitung

Cooper Lighting

Cooper Lighting AMETRIX 1269 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux 8I5355 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1525 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fail-Safe FUS16 Bedienungsanleitung

Cooper Lighting

Cooper Lighting HALO L1765 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Portfolio 883 Bedienungsanleitung

Cooper Lighting

Cooper Lighting 1499 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Lumiere CAMBRIA 200 Bedienungsanleitung

Cooper Lighting

Cooper Lighting METALUX 2HB15 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 640 Bedienungsanleitung

Cooper Lighting

Cooper Lighting Fail-Safe RC Bedienungsanleitung

Cooper Lighting

Cooper Lighting Metalux Indoor Lighting Accessories Bedienungsanleitung

Cooper Lighting

Cooper Lighting Shaper 230 Bedienungsanleitung

Cooper Lighting

Cooper Lighting FAIL-SAFE FDI Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung