CopperOptics PairGain PG-Flex FLC-706 Bedienungsanleitung

PG-FLEX ISDN BASIC RATE INTERFACE

CENTRAL OFFICE TERMINAL CHANNEL UNIT

Model List # Part Number CLEI Code

FLC-706 1 150-1306-01 VACHEGJCAA

PAIRGAIN TECHNOLOGIES, INC.

ENGINEERING SERVICES TECHNICAL PRACTICE

SECTION 363-706-100-01

Revision History of this practice.

Revision 01—June 9, 1997

A) Initial Release.

Section 363-706-100 June 9, 1997 Revision 01

Page ii PairGain Engineering - Plant Series PG-Flex FLC-706

TABLE OF CONTENTS

A. PRODUCT OVERVIEW................................................................................................................1

1. Description and Features....................................................................................................1

2. Front Panel........................................................................................................................2

3. Specifications....................................................................................................................3

B. FUNCTIONAL DESCRIPTION.....................................................................................................3

4. Applications ......................................................................................................................3

5. Operational Capabilities ....................................................................................................4

C. INSTALLATION AND TEST.........................................................................................................4

6. Unpacking.........................................................................................................................4

7. Installation.........................................................................................................................5

8. Troubleshooting.................................................................................................................7

D. TECHNICAL SUPPORT................................................................................................................7

9. Technical Support..............................................................................................................7

E. CERTIFICATION AND WARRANTY..........................................................................................8

10. Certification.....................................................................................................................8

11. Warranty..........................................................................................................................8

F. ABBREVIATIONS..........................................................................................................................9

12. Abbreviations ..................................................................................................................9

USING THIS TECHNICAL PRACTICE

Three types of messages, identified by icons, may appear in the text:

A note informs you of special circumstances.

A caution indicates the possibility of equipment damage.

A warning indicates the possibility of personal injury.

PairGain is a registered trademark, and PG-Flex is a trademark of PairGain Technologies, Inc.

Revision 01 June 9, 1997 Section 363-706-100

PG-Flex FLC-706 PairGain Engineering - Plant Series Page 1

A. PRODUCT OVERVIEW

1. Description and Features

1.1 The PairGain

PG-Flex FLC-706 List 1 ISDN Basic Rate Interface (BRI) Channel Unit (Figure 1)

provides an interface to North American Integrated Services Digital Network (ISDN) Basic Access

services through a PG-Flex Central Office Terminal (COT). The FLC-706 accommodates four ISDN

channels and provides ISDN Line Unit Network Termination (LUNT) at the COT. The FLC-706

installs into a single slot of a PG-Flex Shelf.

1.2 Features of the FLC-706 Channel Unit are:



four ISDN U-interfaces



Mechanized Loop Testing (MLT) compatible and metallic test access



dc resistive test signature



mp/pp-eoc slave mode in 3DS0 format



segmented path performance monitoring



interim path performance monitoring



software provisioning



loopbacks



Pair Gain Test Controller (PGTC) compatible

Revision 01 June 9, 1997 Section 363-706-100

Page 2 PairGain Engineering - Plant Series PG-Flex FLC-706

2. Front Panel

2.1 Figure 1 shows the FLC-706 front panel. Table 1 lists the different states and indications for the

FLC-706 front panel LEDs.

Figure 1. FLC-706 ISDN Channel Unit Front Panel

Table 1. FLC-706 Front Panel LEDs

LED LED State Indicates

ACTIVE*

(1 through 4) Solid green

Fast-flashing green

Slow-flashing green

Channel is in sync

Channel is attempting to sync

Channel is in a maintenance state which is either loo

back or

subscriber circuit testing

FAULT Solid red

Off

A fault has been detected on the unit during powerup

No faults have been detected on the unit during powerup

* Each LED for the four channels has the same states and indications

Section 363-706-100 June 9, 1997 Revision 01

PG-Flex FLC-706 PairGain Engineering - Plant Series Page 3

3. Specifications

Transmission

Code ...........................................................2B1Q (2 binary, one quaternary) at 160 kbps

Network Interface .......................................3DS0 format

Basic Rate Interface....................................2B+D (2 B channels at 64 kbps, one D channel at 16 kbps)

dc Resistive Test Signature .........................120 kΩ

Terminal Impedance ...................................135 Ω

Environmental

Temperature Range.....................................–40º F to +150º F (–40º C to +65º C)

Altitude.......................................................-200 ft. to 13,000 ft. (-60 m to 4,000 m)

Dimensions

Height.........................................................06.75 in. (17.15 cm)

Depth..........................................................10.50 in. (26.67 cm)

Width..........................................................01.00 in. (02.54 cm)

Weight........................................................00.80 lb (00.40 kg)

B. FUNCTIONAL DESCRIPTION

4. Applications

4.1 ISDN is a networking standard that provides end-to-end, simultaneous handling of digitized voice

and data traffic on the same link. Figure 2 shows a typical ISDN configuration. The FLC-706

connects an ISDN Digital Subscriber Line (DSL) to the Central Office (CO). Line Termination (LT)

in the CO occurs at the ISDN switch. The DSL loops are U-interface. The FRC-756 Channel Unit

provides Line Unit Line Termination (LULT) at the RT. The subscriber site has the Network

Termination (NT1).

Figure 2. Typical ISDN Configuration

Revision 01 June 9, 1997 Section 363-706-100

Page 4 PairGain Engineering - Plant Series PG-Flex FLC-706

4.2 Set all options for the FLC-706 through the PG-Flex COT Line Unit or PGTC unit RS-232

maintenance port. Disable ISDN via the maintenance port to prevent time slots from being assigned

to them when they are not in use. The FLC-706 must be plugged into a shelf before any ISDN

provisioning screens can be displayed.

4.3 To provide clocking to the ISDN FLC-706 Channel Unit, ensure the:



composite clock on the PG-Flex COT shelf is connected and properly terminated



FPI-729 card is installed



FAU-728 List 2 card is installed

5. Operational Capabilities

5.1 The FLC-706 ISDN Channel Unit supports two-wire DSL 2B+D data or subsets of that rate. The

B channels (B1 and B2) carry digitized voice and data. The D channel communicates control

signaling and low-speed, packet-switched data.

Segmented path performance monitoring collects the error rates for each DSL loop individually.

Interim path performance monitoring collects the end-to-end error rate for the entire transport path.

5.2 For system isolation and system tests, the FLC-706 provides:



a hybrid transformer that isolates the equipment from the facility and provides coupling and

impedance matching at 135 Ω



metallic test access through the FPI-729 PGTC Interface Unit



MLT compatibility



a DC resistive test signature of 120 kΩfor out-of-service system tests

5.3 The FLC-706 meets the following requirements:



ANSI T1.601-1992 Layer 1



TR-NWT-000397 ISDN Basic Access Transport System Requirements



TR-NWT-000393 ISDN Basic Access Digital Subscriber Lines



TR-TSY-000829 Embedded Operations Channels

C. INSTALLATION AND TEST

6. Unpacking

6.1 Upon receipt of the equipment, visually inspect it for signs of damage. If damage is observed,

report it immediately to the transportation company and PairGain. Order replacement equipment

if necessary.

6.2 Check the contents against the packing slip to ensure complete and accurate shipment. If shipment is

short or irregular, contact PairGain as described in Section 10.3. If you must store the equipment for

a prolonged period, store it in the original box.

Section 363-706-100 June 9, 1997 Revision 01

PG-Flex FLC-706 PairGain Engineering - Plant Series Page 5

7. Installation

7.1 Integration Parameters. Install the FLC-706 into PG-Flex systems with:



List 3 or higher PG-Flex CO Line Unit



List 3 or higher PG-Flex RT Line Unit



an FPI-729 unit (used for clocking) in the COT shelf

Observe normal electrostatic discharge precautions when handling electronic

equipment. Do not hold electronic plug-ins by their edge. Take care not to

touch components or circuitry.

7.2 Install. Insert the FLC-706 into the COT shelf. Ensure the LED indicators:



turn ON for about 2 seconds



turn OFF for about 2 seconds



scan ON from top to bottom



turn OFF

If the LEDs do not follow the above sequence, see Table 2.

7.3 Provision the FLC-706. Provision the FLC-706 using a List 3 or higher CO Line Unit practice.

Access the ISDN Channel Setup menu and select the appropriate options.

7.4 Connect cabling. Connect the DSL and FLC-706:

1Connect the DSL switch in the CO to the appropriate PairGain COT shelf termination for the

ISDN FLC-706 circuit(s) selected. The FLC-706 has four separately configurable circuits.

In step 2, the FRC-756 RT ISDN Channel Unit must be installed and connected to

an NT1 device for the following LED sequence to occur. Otherwise, the LED on

the FLC-706 will continue to fast-flash green and will not synchronize.

2Connect and provision the CO DSL switch termination. Observe, for the channel(s) connected,

that the ACTIVE LED:



is fast-flashing green while the circuit is attempting to synchronize to the CO switch



goes to steady green when the circuit is synchronized to the CO switch

Revision 01 June 9, 1997 Section 363-706-100

Page 6 PairGain Engineering - Plant Series PG-Flex FLC-706

7.5 Verify operation. Verify incoming and outgoing calls for both B channels (where B1 is the

digitized voice channel and B2 is the data channel):

When verifying the B1 and B2 channels, only the B channel used for digitized

voice will have dial tone. The data channel does not have dial tone.

For the verify operation steps, use a Tektronic Craftec CT-100 ISDN type test set

(or equivalent) that can generate a PRBS/2047 pattern to perform a data Bit

Error Rate Test (BERT) when the circuit connects to the far end. This is the

most stressful pattern for ISDN circuits. A test result that does not exceed 10-

Bit Error Rate (BER) must be demonstrated.

7.5.1 Outgoing calls. Verify outgoing calls for both B channels (i.e., calls from the NT1 to the LT per

Figure 2):

1Originate an outgoing B1 voice call and make sure that:



dial tone is present



the number you called is displayed (when answered)



the number from which you called is displayed as the originating number

2Hold up the B1 voice circuit, then switch to the B2 data circuit.

3Originate an outgoing B2 data call to the data loopback (LPBK) test line and perform the BER

test (after the data call is established).

4After the B2 data test is completed, drop the B2 data line, then drop the B1 voice line.

5Return all circuits to normal.

7.5.2 lncoming calls. Verify incoming calls for both B channels (i.e., calls from the LT to the NT1 per

Figure 2):

1To test an incoming B1 voice call:



draw dial tone from another ISDN or POTS circuit



dial the ISDN B1 voice circuit number



verify that the number you called is displayed (when answered)



verify that the number from which you called is displayed as the originating number

2Hold up the B1 voice circuit, then switch to the B2 data circuit.

3Originate an outgoing call on the B2 data circuit using another ISDN data circuit and call the B2

data circuit under test. Then, perform the BER test.

4Drop the B2 data line after the B2 test is completed. Then drop the B1 voice line.

5Return all circuits to normal.

Section 363-706-100 June 9, 1997 Revision 01

PG-Flex FLC-706 PairGain Engineering - Plant Series Page 7

8. Troubleshooting

8.1 Table 2 provides troubleshooting procedures using the front panel LEDs and customer reports. The

FLC-706 supports CO initiated loopbacks.

Table 2. FLC-706 COT Channel Unit Troubleshooting

Indication Problem Action

FAULT LED Fault detected in the PG-Flex system Replace channel unit.

FAULT LED +ACTIVE 1 Internal fault on the FLC-706 Replace channel unit.

FAULT LED +ACTIVE 2 Internal fault on the FLC-706 Replace channel unit.

FAULT LED +ACTIVE 3 Internal fault on the FLC-706 Replace channel unit.

FAULT LED +ACTIVE 4 Internal fault on the FLC-706 Replace channel unit.

ACTIVE LED

SLOW-FLASH Circuit is in either Loopback or

PairGain Test Controller (PGTC)

test setup state

Access the circuit via the PG-Flex Line Unit

maintenance port and release the circuit or wait for

the test originator to complete testing.

ACTIVE LED

FAST-FLASH ISDN circuit lost sync Check loop or for network termination (NT1)

removal by customer.

Customer Reports No

Dial Tone Off-hook not extended to CO Check status LEDs. Clear any indicated trouble. Use

PG-Flex Line Unit maintenance port as required.

Customer Reports Data

Transmission Errors Customer experiencing errors Perform test step 3 from section 7.4. Check

performance monitoring record.

Technician Establishes

Loopback Loopback customer circuit at various

points Use loopback portion of PG-Flex Line Unit

maintenance port to select and activate loopbacks.

D. TECHNICAL SUPPORT

9. Technical Support

9.1 PairGain Technical Assistance is available 24-hours-a-day, 7-days-a-week by contacting PairGain

Customer Service Engineering group at:

Telephone: (800) 638-0031 or (714) 832-9922

Fax: (714) 832-9924

9.2 During normal business hours (8:00 AM to 5:00 PM, Pacific Time, Monday - Friday, excluding

holidays), technical assistance calls are normally answered directly by a Customer Service Engineer.

At other times, a request for technical assistance is handled by an on-duty Customer Service

Engineer through a callback process. This process normally results in a callback within 30 minutes

of initiating the request.

Revision 01 June 9, 1997 Section 363-706-100

Page 8 PairGain Engineering - Plant Series PG-Flex FLC-706

9.3 In addition, PairGain maintains a computer bulletin board system for obtaining current information

on PairGain products, product troubleshooting tips and aids, accessing helpful utilities, and for

posting requests or questions. This system is available 24-hours-a-day by calling (714) 730-3299.

Transmission speeds up to 28.8 kbps are supported with a character format of 8-N-1.

E. CERTIFICATION AND WARRANTY

10. Certification

10.1 FCC compliance: The PG-Flex FLC-706 List 1 ISDN BRI Channel Unit was tested and found to

comply with the limits for Class A digital devices, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause electrical interference in which case the user will be required to correct the

interference at his own expense.

11. Warranty

11.1 PairGain Technologies warrants this product to be free of defects and to be fully functional for a

period of five years from the date of original shipment, given proper customer installation and

regular maintenance. PairGain will repair or replace any unit without cost during this period if the

unit is found to be defective for any reason other than abuse or improper use or installation.

11.2 The FLC-706 should not be field repaired. If it fails, replace it with another unit and return the

faulty unit to PairGain for repair. Any modifications of the unit by anyone other than an authorized

PairGain representative voids the warranty.

11.3 If a unit needs repair:

1Call PairGain for a Return Material Authorization (RMA) number at (800) 638-0031.

2Return the defective unit, freight prepaid, along with a brief description of the problem, to:

PairGain Technologies, Inc.

14402 Franklin Avenue

Tustin, CA 92780-7013

ATTN: Repair and Return Dept.

11.4 PairGain continues to repair faulty units beyond the warranty program at a nominal charge. Contact

your PairGain sales representative for details and pricing.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CopperOptics Netzwerk-Hardware Handbücher

CopperOptics

CopperOptics PairGain PG-Flex FLC-703 Bedienungsanleitung

CopperOptics

CopperOptics PairGain HiGain HRU-512 Bedienungsanleitung

CopperOptics

CopperOptics PairGain HiGain ELU-319 List 5 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex RT FRL-772 List 1 Bedienungsanleitung

CopperOptics

CopperOptics PairGain HiGain HLU-388 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex FSU-796 List 3 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex FCS-718 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex FRL-742 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-FLEX FRC-754 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex FRC-753 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex FCS-718 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex FLL-712 List 1 Bedienungsanleitung

CopperOptics

CopperOptics PairGain HiGain HDU-45 Bedienungsanleitung

CopperOptics

CopperOptics PairGain PG-Flex FCS-719 Bedienungsanleitung

CopperOptics

CopperOptics PairGain HiGain HRU-412 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung