Costar Video Systems CCI2100HW Bedienungsanleitung

USER MANUAL

CCI2100HW

1 Introduction

The network camera supports the network service for a sensor image with progressive scan,

which can be monitored on a real-time screen regardless of distances and locations. By

using its dedicated program, many users are able to have an access to the network camera

at once or a single user can monitor various network cameras at the same time. It also

enables users to play, store and retrieve a monitoring image by using a PC. All the settings

and real-time monitoring screens are also provided through an access to the web.

The network camera is fully featured for security surveillance and remote monitoring needs.

It is based on the DSP compression chip, and makes it available on the network as real-

time, full frame rate Motion JPEG and H.264 video streams.

1.1

Components

This system comes with the followingcomponents;

Network Camera 1

Installation Guide / CD 1

BNC Cable (Optional) 1

U-shaped Mount 1

Bracket Extenders 2

Hardware (two types of mounting screws)

2 Installation

2.1

Basic Configuration of Camera System

The camera must be installed by qualified service personnel in accordance with all local and

federal electrical and building codes.

No.

Description

12VDC

GND

AUDIO IN

AUDIO OUT

GND

ALARM IN

ALARM OUT

GND

VIDEO OUT(CVBS)

GND

NETWORK / PoE

DC - IRIS

C/CS Mount Camera

•

Installing Camera

Mounting Brackets (Optional)

•

Dimension

< CS mount >

2.2

Micro-SD Card Insertion

•

Micro SD memory cardinsertion

User can install and change Micro-SD card as shown in the following picture.

2.3

Connections

•Connecting the Network

Connect a standard RJ-45 cable to the network port of the camera. Generally a crossover cable

is used for directly connecting to a PC, while a direct cable is used for connection to a hub.

•Connecting Audio

Connect audio output line and audio input line.

•Connecting Alarms

–AL_IN (Alarm Input)

You can use external devices to signal the camera to react on events. Mechanical or electrical

switches can be wired to the A1 (Alarm Input 1) and G (Ground) connectors.

–GND (Ground)

NOTE: All the connectors marked G or GND are common.

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

–AL_OUT (Alarm Output)

The camera can activate external devices such as buzzers or lights. Connect the device to the

AO (Alarm Output) and G (Ground) connectors.

•Connecting the Power

Connect power of 12VDC for the camera.

When using a 12VDC adapter, connect the positive (+) pole to the ‘+’ position and the negative

(-) pole to the ‘-’ position.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

–Be careful not to reverse the polarity when you connect the power cable.

2.4. Network Connection & IP assignment

The camera supports operation through the network. When a camera is first connected to the network,

it is necessary to allocate an IP address to the device with the SmartManager utility on the CD.

(Default IP 192.168.0.129)

1) Connect the network camera/device to the network and power up.

2) Start SmartManager utility (Start > All programs > SmartManager > SmartManager).

The main window will display, and after a short while any network devices connected to the network

will be displayed in the list.

3) Select the camera on the list and click right mouse button. You can see the pop-up menu as below.

4) Select Assign IP Address. The Assign IP window will display. Enter the required IP address.

NOTE: For more information, refer to the SmartManager User’s Manual.

3 Operation

The network camera can be used with Windows operating system and browsers. The recommended

browsers are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows.

NOTE: To view streaming video in Microsoft Internet Explorer, set your browser to allow ActiveX

controls.

3.1 Access from a browser

1. Start a browser (Internet Explorer).

2. Enter the IP address or host name of the network camera in the Location/Address field of your

browser.

3. You can see a starting page. Click Live View, Playback, or Setup to enter web page.

4. The network cameras Live View page appears in your browser.

3.2 Access from the internet

Once connected, the network camera is accessible on your local network (LAN). To access the network

camera from the Internet you must configure your broadband router to allow incoming data traffic to

the network camera. To do this, enable the NAT traversal feature, which will attempt to automatically

configure the router to allow access to the network camera. This is enabled from Setup > System >

Network > NAT. For more information, please see “System > Network > NAT” of User’s Manual.

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for the default administrator user must be set. This is done

in the Admin Password dialog, which is displayed when the network camera is accessed for setup at

the first time. Enter your admin name and password, set by the administrator.

NOTE: The default administrator user name and password is admin. If the password is lost, the network

camera must be reset to the factory default settings. Please see Resetting to the factory default

settings.

To prevent network eavesdropping when setting the admin password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate (see NOTE below). To set the

password via a standard HTTP connection, enter it directly in the first dialog shown below. To set the

password via an encrypted HTTPS connection, please see “System > Security > HTTPS” of User’s

Manual.

NOTE: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between

web browsers and servers. The HTTPS certificate controls the encrypted exchange of

information.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Costar Video Systems Sicherheitskamera Handbücher

Costar Video Systems

Costar Video Systems CDIH109 Bedienungsanleitung

Costar Video Systems

Costar Video Systems WDR series Bedienungsanleitung

Costar Video Systems

Costar Video Systems CCIH200SC Bedienungsanleitung

Costar Video Systems

Costar Video Systems CDIH226V Bedienungsanleitung

Costar Video Systems

Costar Video Systems CDI2112SV Bedienungsanleitung

Costar Video Systems

Costar Video Systems CDI2110VIRFH Bedienungsanleitung

Costar Video Systems

Costar Video Systems CDI2110VIRFH Bedienungsanleitung

Costar Video Systems

Costar Video Systems CDC2040MIL Bedienungsanleitung

Costar Video Systems

Costar Video Systems CCI2143HSB Bedienungsanleitung

Costar Video Systems

Costar Video Systems CDI2112PZ2 Bedienungsanleitung

Costar Video Systems

Costar Video Systems DirectIP NVR Bedienungsanleitung

Costar Video Systems

Costar Video Systems CDC2500MI Bedienungsanleitung

Costar Video Systems

Costar Video Systems Network camera CDI2512VIFWH Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung