Craftex CX424 Bedienungsanleitung

MODEL CX424

1.5 HP DUST COLLECTOR

Version 1.0

TABLE OF CONTENTS

General Safety Instructions..................................................................... 3

CX424 Specific Safety Instructions......................................................... 4

Features.................................................................................................. 5

Physical Features ................................................................................... 6

Unpacking............................................................................................... 7

Setup ...................................................................................................... 7

Proper Grounding ................................................................................... 8

Assembly................................................................................................ 9

Test Run ................................................................................................11

Operation................................................................................................12

Maintenance ...........................................................................................12

Bag Cleaning ..........................................................................................12

Cleaning the Canister .............................................................................12

Lubrication..............................................................................................12

Wiring Diagram.......................................................................................13

Parts Breakdown.....................................................................................13

Parts Diagram.........................................................................................14

Parts List.................................................................................................15

Warranty.................................................................................................16

MODEL CX424 –1.5 HP DUST COLLECTOR

As part of the growing line of Craftex woodworking equipment, we are proud to offer the CX424

a 1.5-HP Dust Collector. By following the instructions and procedures laid out in this owner’s

manual, you will receive years of excellent service and satisfaction. The CX424 is a

professional tool and like all power tools, proper care and safety procedures should be

adhered to.

Motor ......................................1.5-HP, Single Phase 120 Volt, 12.5 Amps

Switch.....................................ON/OFF Switch with Removable Key

Balanced Steel Impeller..........Yes

Impeller Size ..........................10”

Air Suction Capacity ...............950 CFM

Noise Level.............................87.1 dB

Collection Bag Volume...........0.15 Cubic Meter

Upper Bags.............................One-Micron Upper Filtration Bag

Intakes....................................1 x 5”, 2 x 4”

Overall Dimension.................. L 34" (850mm) x W 22" (560mm) x H 73" (1860mm)

Mobile Base for Ease of Movement.....Yes

Weight ....................................41 Kg

Warranty.................................3 Years

CX424

FEATURES

UNPACKING

The dust collector is properly packaged in a

carton for safe transportation. When

unpacking, carefully inspect the carton and

ensure that nothing has been damaged.

While doing the inventory if you can not find

any part, check if the part is already

installed on the machine.

Figure-1 Inventory

CONTENTS QTY

A. Collector Ring....................................1

B. Motor / Impeller Unit..........................1

C. Top Bag.............................................1

D. Bottom Bag .......................................1

E. Base Unit...........................................1

F. Dual Inlet 4” Each..............................1

G. Hose..................................................1

H. Outlet Connector...............................1

I. Casters..............................................4

J. Hardware Bag...................................1

K. Gasket...............................................1

L. Collector Ring Supports ....................3

M. Top Bag Support...............................1

N. Hose Clamps.....................................2

O. Bag Clamps.......................................2

SETUP

Before setting up your machine you need to

read and understand this user manual

completely.

The CX424 features four casters installed to

its base unit for easy mobility. If you want to

use the CX424 as a stationary tool, do not

install the casters and find an ideal spot

where your dust collector will most likely be

positioned.

Consider your complete work environment

before placing your machine in the ideal

spot.

PROPER GROUNDING

Grounding provides a path of least

resistance for electric current to reduce the

risk of electric shock.

CX424 is for use on a normal 120 volt

circuit. Make sure that the machine is

connected to an outlet having the same

configuration as the plug. If an adaptor plug

is used, it must be attached to the metal

screw of the receptacle. To prevent

electrical hazards, have a qualified

electrician ensure that the line is properly

wired.

The dust collector should be wired with a

plug having 3 prongs to fit a 3 prong

grounded receptacle as shown in figure-2.

Do not remove the grounding prong to fit it

into a 2 pronged outlet.

Figure-2 120-Volts outlet for CX424

It is strongly recommended not to use

extension cords with your CX424. Always

try to position your machine close to the

power source so that you do not need to

use extension cords.

In case if you really find it necessary to use

an extension cord, make sure the extension

cord does not exceed 50-feet in length and

the cord is 14-gauge to prevent motor

damage.

WARNING!

Improper connection of the equipment-

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician if you are in doubt as to

whether the outlet is properly grounded.

ASSEMBLY

Follow the instructions below to assemble

your CX424.

Place the base unit upside down and install

the swivel casters to the base unit using

screws, nuts and washers provided. See

figure-3.

Figure-3 Installing the casters

Turn the base unit upright and position the

motor / impeller unit on the base unit with

the holes on both units aligned with each

other. Secure the motor / impeller unit to

the base unit using screws and washers

provided. See figure-4.

Figure-4 Installing the motor / impeller unit

on the base unit

Place the gasket on the motor / impeller

opening as shown in figure-5.

Figure-5 Positioning the gasket

Position the outlet connector onto the

gasket and the motor / impeller opening

securing it using screws and washers

provided. See figure-6.

Figure-6 Installing the outlet connector

Attach the three collector ring supports on

to the base unit and secure them using

screws, nuts and washers provided. See

figure-7.

Figure-7 Installing the collector ring support

Attach the collector ring to the collector ring

supports and the upper bag support to the

collector ring as shown in figure-8. Make

sure that the hose opening of the collector

ring is facing the motor / impeller.

Secure the collector ring from both sides

using screws, nuts, and washers provided.

Figure-8 Installing collector ring and the

upper bag support rod

Take the hose provided and attach it with its

one to the outlet connector and the other

end to the collector ring. See figure-9.

Use the hose clamps provided to secure

the hose on both ends.

Figure-9 Connecting the hose from the

outlet connector to the collector ring

Hang the top bag from the support and

install it around the collector ring. Secure it

using bag clamp provided.

Figure-10 Installing the top bag

Attach the foam strip to the bottom of the

collector and trim the excess and evenly

match the ends.

Install the collection bag to the bottom of

the collector ring and secure it by tightening

the collection bag clamp around it as shown

in Figure-11.

Figure-11 Installing the bottom bag

Attach the dual 2 X 4 inlet intake onto inlet

the cover motor/impeller opening as shown

in figure-12 and secure it using screw

provided.

Figure-12 Installing the dual intake

The dual intake has a 4” cover cap, in case

only one intake is used.

TEST RUN

Once you have assembled your dust

collector, it is then time for a test run to

make sure that the machine works properly

and is ready to use.

Remove all the tools used for assembling

the machine components. Walk around the

machine, ensure all nuts, bolts, and screws

are tightened and the machine is properly

assembled. Connect the cord to the power

source and turn the machine ON.

During the test run if there is any unusual

noise coming from the machine or the

machine vibrates excessively, turn OFF the

power switch immediately and disconnect

the cord from the power source. Investigate

to see if you can find out what the problem

with your machine.

Turn the dust collector OFF and remove the

disabling key from the ON/OFF switch and

try to start the machine.

Figure-13 Disabling key

If the machine starts, immediately stop the

machine. The switch disabling feature is not

working on your machine and it should be

fixed.

If the machine does not start, the switch

disabling key is working.

WARNING!

Before starting the machine, make sure

that you have read and understood the

user manual and you are familiar with the

safety features of the machine. Failure to

do so may cause serious personal injury.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Craftex Staubabscheider Handbücher

Craftex

Craftex CX series Bedienungsanleitung

Craftex

Craftex CSX Series Bedienungsanleitung

Craftex

Craftex CX414 Bedienungsanleitung

Craftex

Craftex CX401 Bedienungsanleitung

Craftex

Craftex CX418 Bedienungsanleitung

Craftex

Craftex CX405 Bedienungsanleitung

Craftex

Craftex CX404 Bedienungsanleitung

Craftex

Craftex CT126 Bedienungsanleitung

Craftex

Craftex CT167 Bedienungsanleitung

Craftex

Craftex CT186 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung