Craftex CT015N Bedienungsanleitung

15” WOOD BAND SAW – CT015N

3-speed 15” Wood Band Saw - Model CT015N

General Safety Instructions Page 3

Specific Safety Instructions Page 4

Features Page 5

Features Illustration Page 6

Unpacking Page7

Tools Necessary for Assembly and Optional Page 8

Accessories for the CT015N

CT015N Band Saw Assembly

Motor Mount Assembly Pages 9-10

Assembling the Stand Pages 11-12

Mounting the Saw to the Base Pages 13-14

Pulleys and Belts Pages 15-17

Adjusting Blade and Bottom Bearings Page 18

Assembling the Saw Table Page 19

Assembling the Fence Page 20

Adjusting the Top Bearings Page 21

Attaching the Dust Collection Hose, Pulley Page 22

Cover and Back Panel

Troubleshooting Pages 23-24

Frame Schematic Drawing Page 25

Case Schematic Drawing Page 26

Base and Motor Schematic Drawing Page 27

Table Parts Schematic Drawing Page 28

Fence Schematic Drawing Page 29

PartsList Pages30-32

Optional Blades Page 33

A Helping Hand Page 34

Warranty Page35

GENERAL SAFETY INSTRUCTIONS

Extreme caution should be used when operating all power tools.

Know your power tool, be familiar with its operation, read through the owner’s manual

and practice safe usage procedures at all times.

• CONNECT your machine ONLY to the matched and specific power source.

• ALWAYS WEAR SAFETY GLASSES, RESPIRATORS, HEARING PROTECTION

AND SAFETY SHOES when operating your machine.

• DO NOT WEAR LOOSE CLOTHING OR JEWELLERY when operating your machine.

• A SAFE ENVIRONMENT IS IMPORTANT. Keep the area free of dust, dirt and other

debris in the immediate vicinity of your machine.

• BE ALERT! Do not use prescription or other drugs that may affect your ability or

judgement to safely use your machine.

• DISCONNECT the power source when changing drill bits, hollow chisels, router bits,

shaper heads, blades, knives or making other adjustments or repairs.

• NEVER leave a tool unattended while it is in operation.

• NEVER reach over the table when the tool is in operation.

• NEVER make crosscuts with the rip fence in place.

• NEVER attempt to cut material that is warped or twisted.

• NEVER attempt a procedure if it does not feel safe or comfortable.

• ALWAYS keep blades, knives and bits sharpened and properly aligned.

• ALWAYS keep all safety guards in place and ensure their proper function.

• ALWAYS use push sticks and featherboards to safely feed your work though the

machine.

• ALWAYS make sure that any tools used for adjustments are removed before

operating the machine.

• ALWAYS secure your work with the appropriate clamps or vises.

• ALWAYS keep bystanders safely away while the tool is in operation.

THINK SAFETY. WORK SAFELY.

BAND SAW -CT015N- SAFETY INSTRUCTIONS

A band saw may not appear to be a dangerous tool but it is always important to use

consideration and caution during its operation: remember, a band saw can sever a

finger just as easily and quickly as a table saw.

Please take the necessary precautions to ensure the safe operation of your band saw.

• ALWAYS ensure that the blade tension is properly set for the type and width of blade

installed.

• ALWAYS ensure that the guide blocks are properly set to prevent blade wander.

• ALWAYS make certain that the bearings are properly adjusted to guide the blade.

• ALWAYS ensure that the band saw teeth are pointing in a downward direction.

• ALWAYS ensure that the band saw blade guard is no more than 1/2” above your

stock.

• ALWAYS turn OFF the machine if you are backing out a cut.

• Make relief cuts before cutting short curves.

• NEVER turn ON the band saw if the blade is in contact with your stock.

• DO NOT attempt to remove jammed pieces unless the band saw has come to a

complete stop and the power switch has been turned to the OFF position.

INTRODUCTION

The Craftex name guarantees excellence, dependability and durability; by following the

instructions and procedures laid out in this owner’s manual your machine will provide

excellent service and satisfaction for years to come. The CT015N 3-speed 15” Band

Saw is a professional woodworking tool, and like all power tools, proper care and safety

precautions should be exercised at all times.

This owner’s manual will take woodworking novices and professionals alike through the

step-by-step process of assembling the CT015N Band Saw. As well, troubleshooting

tips on how to correct problems with your band saw’s operation will serve as handy

references throughout the life of the machine. Hold on to this manual and keep it

someplace safe when you have completed your assembly.

Note: there will be points in the assembly process where it is helpful to have the

assistance of a second person. Please read through the entire manual and familiarize

yourself with each step before starting the assembly process.

CT015N Features

• Precision-ground cast-iron table

• Table size: 14 inches x 14 inches

• Table tilts right 0 to 45 degrees

• Throat size: 14 1/2 inches

• Heavy-duty cast-iron frame

• Precision balanced aluminum drive wheels with rubber tires

• Blade guides: 3 ball bearings, upper and lower

• Motor: 1HP, 110 volt

• Speeds: 750, 1230 and 2800 FPM

• Maximum cutting height: 6 inches (10 inches with the addition of the Extension Block

Riser, Model #CT015EXT)

• Blade width: 1/8 inch to 1 inch

• Blade length: 97 1/2 inches

• Mitre gauge included

• Precision aluminum T-fence with optical cursors

• Safety switch with removable key

• Solid sheet-metal base

• 3-inch dust port with adaptor

• Gross weight: 97kgs

• Two-year Craftex warranty

3-SPEED 15” WOOD BAND SAW

MODEL CT015N FEATURES

UNPACKING YOUR CT015N BAND SAW

Your Craftex band saw is shipped in one large carton. Before unpacking the parts, be

sure to have a clean, well-lit and uncluttered area to take inventory of the carton’s

contents. Each step in this manual comes with its own parts list and any other tools

necessary to complete the assembly step; you may find it helpful to refer to these lists

when unpacking the contents and group together the parts for each step as you go

(there is also a full parts list at the end of this manual).

Care should be taken when unpacking these machine parts. Safety glasses and work

gloves are recommended, as there may be sharp edges and staples that could cause

personal injury.

Carefully remove all packing materials and recycle these where facilities exist.

Open all packages, remove the contents, and set the packaging aside; be sure that all

packages are empty before discarding them.

After removing the packages of hardware, tilt the shipping carton on its end and slide

out the saw table.

BE CAREFUL: the saw blade is already installed and exposed. Gently loosen the saw

table out of the box by gripping the drive wheel shaft, and then wiggle it the rest of the

way out of the box. Once it is out of the shipping carton, lower the guard to cover the

saw blade.

Your CT015N Band Saw is shipped with a protective coating on the top surface of the

cast-iron saw table to prevent rust and corrosion. This coating should be removed prior

to assembly. Use a cloth and mineral spirits or varsol to wipe the surface clean and then

dry it with a separate cloth. After it is dry, apply a coat of heavy-duty paste wax and then

buff dry (this will help protect the surface from future corrosion).

PLEASE READ THROUGH EACH STEP OF THIS MANUAL

BEFORE ASSEMBLING YOUR CT015N BAND SAW

Tools you will need on hand to assemble

your CT015N Band Saw:

10mm wrench Phillips screwdriver

10mm wrench socket

Rubber mallet

12mm wrench

12mm wrench socket Machinist’s square

14mm wrench Allen keys: supplied

14mm wrench socket

Optional Accessories for your CT015N Band Saw:

CT001 Circle Cutting Attachment:

This attachment guides in cutting accurate circles from 4 inches to 24 inches in

diameter. The bracket remains on the machine.

CT015EXT Extension Kit:

This kit includes an extension block, extension rod, blade and blade guard to increase

the cutting height of the band saw from 6 inches to 10 inches.

STEP ONE:

MOTOR MOUNT ASSEMBLY

Parts required (with part#): Qty: Tools required:

201: stand top 1 14mm wrench

209: motor 1

212: motor plate 1

210: motor knob 1

213: eye screw 1

205: nuts, 5/16” 4

214: self-locking nuts, 3/8” 3

215: hex bolt, 3/8” x 1 1/4” 1

216: flat washers, 5/16”-20 4

217: hex bolt, 3/8” x 3/4” 2

218 hex bolt, 5/16” x 3/4” 4

221: flat washer, 3/8” 1

1. With the motor plate/motor mount bracket (part #212) upside down, assemble it

to the motor (#209), using 3/4” bolts (#218), washers (#216) and nuts (#205).

Tighten only fingertip tight (final tightening will be done when adjusting drive belt

tension in STEP FOUR, #8).

STEP ONE (continued)

2. Turn the stand top upside down. Insert the eye

screw (#213) in the slot on the underside of the

stand top using 1 1/4” bolt (#215) and nut (#214).

Tighten but ensure that it can still move freely (it

should be able to hold its position but still pivot).

3. Slot the motor plate into the stand and bolt in with

3/4” bolts (#217) and nuts (#214). Nuts should be

snug but not tight.

4. Slip the eye screw through the hole in the motor plate; slip on washer (#221).

Attach the motor knob (#210) to the end of the eye screw.

Inhaltsverzeichnis

Andere Craftex Gesehen Handbücher

Craftex

Craftex CX204N Bedienungsanleitung

Craftex

Craftex CX204 Bedienungsanleitung

Craftex

Craftex CT103N Bedienungsanleitung

Craftex

Craftex CT104 Bedienungsanleitung

Craftex

Craftex CX207 Bedienungsanleitung

Craftex

Craftex B2397 Bedienungsanleitung

Craftex

Craftex CX110 Bedienungsanleitung

Craftex

Craftex B1012 Bedienungsanleitung

Craftex

Craftex CX122 Bedienungsanleitung

Craftex

Craftex CX212 Bedienungsanleitung

Craftex

Craftex CX112 Bedienungsanleitung

Craftex

Craftex CT146 Bedienungsanleitung

Craftex

Craftex B2062L Bedienungsanleitung

Craftex

Craftex CX119N Bedienungsanleitung

Craftex

Craftex CX101N Bedienungsanleitung

Craftex

Craftex CX116 Bedienungsanleitung

Craftex

Craftex CX series Bedienungsanleitung

Craftex

Craftex CX101 Bedienungsanleitung

Craftex

Craftex CX102 Bedienungsanleitung

Craftex

Craftex CX series Bedienungsanleitung

Craftex

Craftex CX118 Bedienungsanleitung

Craftex

Craftex CT073 Bedienungsanleitung

Craftex

Craftex B2214 Bedienungsanleitung

Craftex

Craftex CX series Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung