Craftsman CMXEOCG232 Bedienungsanleitung

Owner's Manual

GARAGE DOOR OPENER

For Residential Use Only

MODELS CMXEOCG232 and CMXEOCG472

READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS BEFORE FIRST USE

OF THIS PRODUCT.

FASTEN THE MANUAL NEAR THE GARAGE DOOR AFTER INSTALLATION.

PERIODIC CHECKS OF THE OPENER ARE REQUIRED TO ENSURE SAFE OPERATION.

DO NOT INSTALL ON A ONE-PIECE DOOR IF USING DEVICES OR FEATURES PROVIDING

UNATTENDED CLOSE.

UNATTENDED DEVICES AND FEATURES ARE TO BE USED ONLY WITH SECTIONAL DOORS. SEE

PAGE 3.

WWW.CRAFTSMAN.COM

INTRODUCTION 3

Safety Symbol Review and Signal Word Review 3

Unattended Operation 3

Preparing Your Garage Door 3

Tools Needed 4

Test the Wi-Fi® Signal Strength in Your Garage 4

Planning 5

Carton Inventory 7

Hardware Inventory 8

ASSEMBLY 9

Assemble the Rail and Install the Trolley 9

Fasten the Rail to the Motor Unit 9

Install the Idler Pulley 10

Install the Chain/Cable 11

Tighten the Chain 12

INSTALLATION 12

Important Installation Instructions 12

Determine the Header Bracket Location 13

Install the Header Bracket 14

Attach the Rail to the Header Bracket 15

Position the Opener 16

Hang the Opener 17

Install the Lights 18

Attach the Emergency Release Rope and Handle 18

Fasten the Door Bracket 19

Connect Door Arm to Trolley 21

Attach the Warning Labels 22

Install the Door Control - Model CMXEOCG232 23

Install the Door Control - Model CMXEOCG472 24

Install The Safety Reversal System 25

Electrical Requirements 28

Aligning the Safety Reversing Sensors 28

ADJUSTMENT 29

Introduction 29

1 - Program the Travel 30

2 - Automatic Force Set Up 30

3 - Test the Safety Reversal System 31

4 - Test the Protector System® 31

myQ® SMARTPHONE CONTROL 32

Connect With Your Smartphone 32

OPERATION 33

Important Safety Instructions 33

Features 34

Using Your Garage Door Opener 34

Using the Door Control - Model CMXEOCG232 34

Using the Door Control - Model CMXEOCG472 35

Remote Control 36

To Erase the Memory 36

To Open the Door Manually 37

The Remote Control Battery 37

Care of Your Opener 37

TROUBLESHOOTING 38

REPAIR PARTS 39

Rail Assembly Parts 39

Installation Parts 39

Motor Unit Assembly Parts - Model CMXEOCG232 40

Motor Unit Assembly Parts - Model CMXEOCG472 41

ACCESSORIES 42

WARRANTY 42

AUTOMATIC GARAGE DOOR OPENER SAFETY &

MAINTENANCE GUIDE 43

TABLE OF CONTENTS

INTRODUCTION

SAFETY SYMBOL REVIEW AND SIGNAL

WORD REVIEW

This garage door opener has been designed and tested to offer safe

service provided it is installed, operated, maintained and tested in

strict accordance with the instructions and warnings contained in this

manual.

Mechanical

Electrical

When you see these Safety Symbols and Signal Words on the

following pages, they will alert you to the possibility of

serious injury

or death

if you do not comply with the warnings that accompany

them. The hazard may come from something mechanical or from

electric shock. Read the warnings carefully.

When you see this Signal Word on the following pages, it will alert you

to the possibility of damage to your garage door and/or the garage

door opener if you do not comply with the cautionary statements that

accompany it. Read them carefully.

WARNING: This product can expose you to chemicals

including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm. For

more information go to

www.P65Warnings.ca.gov

UNATTENDED OPERATION

Any device or feature that allows the door to close without being in the

line of sight of the door is considered unattended close. Devices that

allow unattended operation are to be used ONLY with sectional

doors.

PREPARING YOUR GARAGE DOOR

To prevent possible SERIOUSINJURYor DEATH:

•ALWAYS call a trained door systems technician if garage door

binds, sticks, or is out of balance. An unbalanced garage door

may NOT reverse when required.

•NEVER try to loosen, move or adjust garage door, door

springs, cables, pulleys, brackets or their hardware, ALLof

which are under EXTREME tension.

•Disable ALLlocks and remove ALLropes connected to garage

door BEFORE installation and operating garage door opener

to avoid entanglement.

•DO NOT install on a one-piece door if using devices or

features providing unattended close. Unattended devices and

features are to be used ONLY with sectional doors.

To prevent damage to garage door and opener:

•ALWAYS disable locks BEFORE installing and operating the

opener.

•ONLY operate garage door opener at 120V, 60Hz to avoid

malfunction and damage.

Before you begin:

1. Disable locks and remove any ropes connected to the garage

door.

2. Lift the door halfway up. Release the door. If balanced, it

should stay in place, supported entirely by its springs.

3. Raise and lower the door to check for binding or sticking. If

your door binds, sticks, or is out of balance, call a trained door

systems technician.

4. Check the seal on the bottom of the door. Any gap between

the floor and the bottom of the door must not exceed 1/4"

(6mm). Otherwise, the safety reversal system may not work

properly.

5. The opener should be installed above the center of the door. If

there is a torsion spring or center bearing plate in the way of

the header bracket, it may be installed within 4feet (1.2 m) to

the left or right of the door center. See page13.

Sectional Door One-Piece Door

TOOLS NEEDED

During assembly, installation and adjustment of the opener,

instructions will call for hand tools as illustrated below.

Drill Bits 3/16",

5/16", and 5/32"

Claw Hammer

Carpenter’s Level

(optional)

Pencil

Screwdriver

Drill

Wire Cutters

Adjustable End Wrench

Tape Measure

Pliers

Sockets and Wrench 1/2",

5/8", 7/16", 9/16", and 1/4"

Hack Saw

Stepladder

TEST THE WI-FI®SIGNAL STRENGTH IN

YOUR GARAGE

Monitor and control your garage door from anywhere using the myQ®

App. You will need a router with Wi-Fi and a smartphone or other

mobile device. Make sure your mobile device is connected to your

Wi-Fi network. Hold your mobile device in the place where your

garage door opener will be installed and check the Wi-Fi signal

strength.

Wi-Fi signal is weak.

The garage door opener will likely connect to

your Wi-Fi network. If not, try one of the

options below.

No Wi-Fi signal.

Try one of the following:

• Move your router closer to the garage door

opener to minimize interference from walls

and other objects

• Buy a Wi-Fi range extender

Check Signal Strength. If you see:

Wi-Fi signal is strong.

You’re all set!

Install your new garage door opener.

Visit support.chamberlaingroup.com for more details

See myQ®App Control page 32 to connect your garage door opener

to your Wi-Fi network. Do NOT connect prior to installation.

Wi-Fi®is a registered trademark of Wi-Fi Alliance

PLANNING

Identify the type and height of your garage door. Survey your garage

area to see if any of the conditions below apply to your installation.

Additional materials may be required. You may find it helpful to refer

back to this page and the accompanying illustrations as you proceed

with the installation of your opener. Depending on your

requirements, there are several installation steps which may call for

materials or hardware not included in the carton.

•Installation Step 1 – Look at the wall or ceiling above the

garage door. The header bracket must be securely fastened

to structural supports.

•Installation Step 5 – Do you have a finished ceiling in your

garage? If so, a support bracket and additional fastening

hardware may be required.

•Installation Step 12 – Depending upon garage construction,

extension brackets or wood blocks may be needed to install

sensors.

•Installation Step 12 – Alternate floor mounting of the safety

reversing sensor will require hardware not provided.

•Do you have an access door in addition to the garage door?

If not, an emergency key release is required.

•Look at the garage door where it meets the floor. Any gap

between the floor and the bottom of the door must not

exceed 1/4" (6 mm). Otherwise, the safety reversal system

may not work properly. See Adjustment Step 2. Floor or door

should be repaired.

SECTIONAL DOOR INSTALLATION

•Do you have a steel, aluminum, fiberglass or glass panel

door? If so, horizontal and vertical reinforcement is required

(Installation Step 8).

•The opener should be installed above the center of the door.

If there is a torsion spring or center bearing plate in the way

of the header bracket, it may be installed within 4 feet (1.22

m) to the left or right of the door center. See Installation

Steps 1 and 8.

•If your door is more than 7 feet (2.13 m) high, see rail

extension kits listed on Accessories page.

Safety Reversing Sensor

Header Wall

Access Door

Safety Reversing

Sensor

Gap between ﬂoor

and bottom of door

must not exceed 1/4" (6 mm).

Extension Spring

Horizontal and vertical reinforcement

is needed for lightweight garage doors

(ﬁberglass, steel, aluminum, door with

glass panels, etc.).

Support bracket &

fastening hardware

is required.

FINISHED CEILING

Wall-mounted

Door Control

Torsion Spring

Slack in chain tension

is normal when garage

door is closed.

Vertical

Centerline

of Garage

Door

Emergency

Release Rope

& Handle

Straight

Door

Arm

Garage

Door

Spring

Door

Bracket

Header

Bracket

Garage

Door

Header

Wall

CLOSED POSITION

Rail Tab

Curved

Door Arm

Chain

Trolley

SECTIONAL DOOR INSTALLATION

Motor unit

PLANNING (CONTINUED)

ONE-PIECE DOOR INSTALLATIONS

•Generally, a one-piece door does not require reinforcement.

If your door is lightweight, refer to the information relating to

sectional doors in Installation Step 8.

•Depending on your door’s construction, you may need

additional mounting hardware for the door bracket

(Installation Step 8).

Without a properly installed safety reversing sensor, persons

(particularly small children) could be SERIOUSLY INJURED or

KILLED by a closing garage door.

•The gap between the bottom of the garage door and the floor

MUST NOT exceed 1/4" (6 mm). Otherwise, the safety

reversal system may NOT work properly.

•The floor or the garage door MUST be repaired to eliminate

the gap.

Safety Reversing Sensor

Access

Door

FINISHED CEILING

Support bracket

and fastening

hardware is required.

See page 16.

Safety Reversing

Sensor

Header Wall

Gap between ﬂoor

and bottom of door must

not exceed 1/4" (6 mm).

Rail

Slack in chain tension

is normal when garage

door is closed.

Access

Door

Safety Reversing Sensor

Gap between ﬂoor and bottom of door must

not exceed 1/4" (6 mm).

Header

Bracket

Straight

Door

Arm

Emergency

Release

Rope & Handle

Door Bracket

Curved

Door

Arm

Header

Wall

Cable

Rail

Garage Door

CLOSED POSITION

Rail Tab

Straight Door

Arm

Curved

Door Arm

Door

Bracket

Header

Bracket

Garage

Door

Header

Wall

CLOSED POSITION

Rail Tab Chain

Rail

Cable

ONE-PIECE DOOR WITHOUT TRACK

ONE-PIECE DOOR WITH TRACK

Motor Unit

Wall-mounted

Door Control

CARTON INVENTORY

Your garage door opener is packaged in one carton which contains

the motor unit and all parts illustrated below. Accessories will

depend on the model purchased. If anything is missing, carefully

check the packing material.

Hardware for assembly and installation is shown on the next page.

Save the carton and packing material until installation and

adjustment is complete.

Straight Door

Arm Section

Curved Door

Arm Section

Safety Labels

and

Literature

2-Conductor Bell Wire

White & White/Red

Idler Pulley

001A5295

Chain and Cable

Hanging Brackets

(2) Safety Reversing Sensors

(1 Sending Sensor and 1 Receiving Sensor)

with 2-Conductor White & White/Black

Bell Wire attached

Door Bracket

Trolley

Safety Sensor

Bracket (2)

Rail

Center/Back

Sections

"U" Bracket

Rail

Front (header)

Section

Header Bracket

Chain Spreader

Motor Unit with a Light Lens

CMXEOCG232 CMXEOCG472

Motor Unit with 2 Light Lenses

Standard Doorbell 3-Button Remote Control

Dual-Function

Control Panel

HARDWARE INVENTORY

Separate all hardware and group as shown below for the assembly and installation procedures.

Handle

091B0019-1

Nut 5/16"-18 (6)

133A0028

Ring

Fastener (3)

158A0047

Insulated Staples

(Not shown)

131A0031

Drywall Anchors (2)

133A0126

Clevis Pin

5/16"x1"

146A0058

Rope

Lock Washer 5/16" (5)

216A0025

Lag Screw

5/16"-9x1-5/8" (4)

171A0480

Hex Bolt

5/16"-18x7/8" (4)

171A0301

Clevis Pin

5/16"x1-1/4"

146A0074

Screw

6ABx1" (2)

171A0361

Screw 6-32x1" (2)

171A0475

Clevis Pin

5/16"x1-1/2"

1460100

Self-Threading Screw

1/4"-14x5/8" (2)

171A0540

INSTALLATION HARDWARE

ASSEMBLY HARDWARE

Master

Link (2)

Idler Bolt

Nut 3/8"

Trolley Threaded Shaft

Lock Washer 3/8"

Lock Nut

1/4"-20

Bolt

1/4"-20x1-3/4"

Hexagonal Screw 10-24 (2)

Wing Nut 1/4"-20 (2)

ASSEMBLY STEP 1

ASSEMBLE THE RAIL AND INSTALL THE

TROLLEY

To prevent INJURY from pinching, keep hands and fingers away

from the joints while assembling the rail.

To avoid installation difficulties, do not run the garage door opener

until instructed to do so.

The front rail has a cut out “window” at the door end. The front rail has

a rail tab. This tab MUST be on the top of the rail when assembled.

1. Remove the straight door arm and hanging bracket packaged

inside the front rail and set aside for Installation Step 5 and 9.

NOTE: To prevent INJURY while unpacking the rail carefully

remove the straight door arm stored within the rail section.

2. Align the rail sections on a flat surface as shown and slide the

tapered ends into the larger ones. Tabs along the side will

lock into place.

3. Place the motor unit on packing material to protect the cover,

and rest the back end of the rail on top. For convenience, put

a support under the front end of the rail.

4. As a temporary stop, insert a screwdriver into the hole 10" (25

cm) from the front end of the rail, as shown.

5. Check to be sure there are 4 plastic wear pads inside the

inner trolley. If they became loose during shipping, check all

packing material. Snap them back into position as shown.

6. Slide the trolley assembly along the rail from the back end to

the screwdriver.

7. Slide the rail onto the “U” bracket, until it reaches all the stops

on the top and sides of the “U” bracket.

To garage

door opener

(TO MOTOR UNIT)

“U” Bracket

Outer Trolley

Inner Trolley

Wear Pads

SLIDE TO STOPS

ON TOP AND

SIDES OF

“U” BRACKET

Front Rail

Section

(TO DOOR)

Rail

Tab

Trolley

Window

Cut-Out

Idler

Pulley

Hole

ASSEMBLY STEP 2

FASTEN THE RAIL TO THE MOTOR UNIT

To avoid SERIOUS damage to garage door opener, use ONLY

those bolts/fasteners mounted in the top of the opener.

1. Insert a 1/4"-20 x 2-1/2" bolt into the cover protection bolt hole

on the back end of the rail as shown. Tighten securely with a

1/4"-20 lock nut. DO NOT overtighten.

2. Remove the bolts from the top of the motor unit.

3. Use the carton to support the front end of the rail.

4. Place the “U” bracket, flat side down onto the motor unit and

align the bracket holes with the bolt holes.

5. Fasten the “U” bracket with the previously removed bolts; DO

NOT use any power tools. The use of power tools may

permanently damage the garage door opener.

6. Attach chain spreader to the motor unit with two screws.

HARDWARE SHOWN ACTUAL SIZE

Bolt

1/4"-20x1-3/4"

Lock Nut

1/4"-20

“U” Bracket

Hex Screws

8-32x7/16

Cover

Protection

Bolt Hole

Bolt

Lock Nut

Bolts (Mounted in the

garage door opener)

Chain

Spreader

NOTE: Your product may look different than the illustrations.

ASSEMBLY STEP 3

INSTALL THE IDLER PULLEY

1. Lay the chain/cable beside the rail, as shown. Grasp the end

of the cable and pass approximately 12" (30 cm) of cable

through the window. Allow it to hang until Assembly Step4.

2. Remove the tape from the idler pulley. The inside center

should be pre-greased. If dry, regrease to ensure proper

operation.

3. Place the idler pulley into the window as shown.

4. Insert the idler bolt from the top through the rail and pulley.

Tighten with a 3/8" lock washer and nut underneath the rail

until the lock washer is compressed.

5. Rotate the pulley to be sure it spins freely.

6. Locate the rail tab. The rail tab is near the idler pulley on the

front rail section. Use a flat head screwdriver and lift the rail

tab until the tab is vertical (90º).

Lock

Washer

3/8"

Idler Bolt Rail Tab

Idler Pulley

Screwdriver

CORRECT INCORRECT

Chain and Cable

Cable Link

Rail Tab

Nut 3/8"

Idler Bolt

HARDWARE SHOWN ACTUAL SIZE

Trolley

Lock Washer 3/8"

Nut 3/8"

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Craftsman Garagentoröffner Handbücher

Craftsman

Craftsman 139.53525SRT Bedienungsanleitung

Craftsman

Craftsman 139.53225SRT Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Craftsman

Craftsman 958501 Bedienungsanleitung

Craftsman

Craftsman 139.53976SRT Bedienungsanleitung

Craftsman

Craftsman 200.57983 Bedienungsanleitung

Craftsman

Craftsman 139.53335SRT3 Bedienungsanleitung

Craftsman

Craftsman 139.53800SRT Bedienungsanleitung

Craftsman

Craftsman 139.53916D Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Craftsman

Craftsman 39.18451D Bedienungsanleitung

Craftsman

Craftsman 139.53939D Bedienungsanleitung

Craftsman

Craftsman 139.53648D Bedienungsanleitung

Craftsman

Craftsman 139.53990D Bedienungsanleitung

Craftsman

Craftsman 139.53964SRT Bedienungsanleitung

Craftsman

Craftsman 139.5364812 Bedienungsanleitung

Craftsman

Craftsman 139.53491SRT Bedienungsanleitung

Craftsman

Craftsman 139.53990DS Bedienungsanleitung

Craftsman

Craftsman 139.5399211 Bedienungsanleitung

Craftsman

Craftsman 139.53962 SRT Bedienungsanleitung

Craftsman

Craftsman 139.53669SRT Bedienungsanleitung

Craftsman

Craftsman ASSURELINK 139.53999 Bedienungsanleitung

Craftsman

Craftsman 139.53939D Bedienungsanleitung

Craftsman

Craftsman 139.53725 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Chamberlain

Chamberlain 8355 - 1/2 hp Bedienungsanleitung