Craftsman 917.380221 Bedienungsanleitung

OWNER'S

Caution:

Readand Follow

alaSafetyRules

andInstructions

BeforeOperating

ThisEquipment

CRAFrSMIZN

3.5 RESERVEPOWER

20" SIDEDISCHARGE

ROTARYLAWNMOWER

Assembly

Operation

Maintenance

ServiceandAdjustment

RepairParts

iml_l ill

/l_JlMm_lll .................................... II i II i _ II

SEARS,ROEBUCKANDCo., Chicago,IL. 60684 U.S.A.

SAFETYRULES

CAUTION: ALWAYS DISCONNECT SPARK PLUG 'WIRE AND PLACE WiRE

WHERE 11'CANNOT CONTACT SPARK PLUG TO PREVENT ACCIDENTAL STAR-

TING WHEN SETTING-UP, TRANSPORTING, ADJUSTING OR MAKING

REPAIRS TO YOUR MOWER_

IMPORTANT

FEDERAL REGULATIONS REQUIRE OPERATOR PRESENCE BLADE STOP CONTROLS TO MINIMIZE THE

RISK OF BLADE CONTACT INJURY. YOUR MOWER IS EQUIPPED WITH SUCH CONTROLS. DO NOT

ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROL UNDER ANY

CIRCUMSTANCES°

• BE CAREFUL-WHEN THE ENGINE IS RUN-

NING, THE BLADE IS TURNING.

• Please read your' owner's manual_ Only allow

persons who know the safety rules to use your

mower,

• DO NOT tie the operator presence control bar

to the handle. Control must be lye° to permit

broke engagement when handles and control

are reteased_

° DO NOT allow children to use your' mower_

• Check your mower over' before each use_

Tighten any loose bolts, nuts, etc_

• Remove all sticks, stones, wires, cans, boards,

etc_from area to be mowed_ These objects can

be thrown by the blade.

•DO NOT allow children, bystanders or pets in

the area while mowing°

• Always ",,,,earshoes when mowing° DO NOT

operate mower when barefoot or wearing

open sandals.

• Always wear safety glasses or' eye shields

before starting your lawn mower and while

mowing.

• Always shut off engine before trying to adjust

wheetheightso

• When engine is running, DO NOT put hands

or' feet under mower or in the discharge chute,

nor make any adjustments.

• Stay clear' of discharge opening at all times°

• Do not fill gas tank when engine is running,

when indoors or when engine is hot. Allow

engine to cool for several minutes before fill-

ing gas tank Clean off any spilled gasoline

before starting engine.

• Mow only in goodllght.

• Always stop blade when not cutting grass or

when crossing gravel drive, sidewalk, or

roadway_

" DO NOT continue to run your mower' if you

hit a foreign objecL Stop the engine, discon_

nect the spark plug wire from the spark plug,

inspect the mower for damage and make

repairs as required_

• DO NOT use a damaged mower. Always have

damage repaired before mowing.

• DO NOT run your mower if it vibrates too

much. Stop engine and make repairs. Vibra-

tion is an indication of damage_

• Never use your mower without proper guards

or' deflectors in place. - -

• Always mow across a slope or inclined area.

DO NOT mow up or down a slope or inclined

area.

• DO NOT mow in wet grass. Be careful of

footing when mowing in wet grass, use shoes

with good traction.

• DO NOT run with the mower_

•DO NOT run your mower indoors. Exhaust

gases are deadly poison.

° Always disconnect the spark plug wire from the

spark plug to prevent accidental starting when

transporting or' storing your mower after the

mowing season.

•DO NOT attempt to raise engine speed above

factory settings_ Engine damage or personal

injury may result.

° If a grass catcher is used on your' mower', check

the catcher often for' damage or deterioration.

It will wear through normal use. Use only a

recommended replacement catcher.

• Always stop blade to remove or instaJt catcher_

" DO NOT store your mower' or gasoline where

fumes may reach an open flame and cause a

fire.

• DRAIN THE GASOLINE from your mower

before transporting your mower inside your car

or other vehicle.

ill ii illll,llllllll JllllllJllll illl i lll ill iiiii

LOOKFORTHISSYMBOLTOPOINTOUTIMPOR-

TANTSAFETYPRECAUTIONS.ITMEANS--ATTEN-

TION!!! BECOMEALERT!!! YOUR SAFETY IS

INVOLVED.

CONGRATULATIONSonyourpurchaseofaSearsCrafts-

manLawnMower.Ithasbeendesigned,engineered

and manufacturedtogive you the bestpossible

dependabilityandperformance.

Shouldyouexpermnceanyproblemyoucannot easi-

ly remedy, please contact your nearest Sears Ser-

vice Center/Department. We have competent, well-

trained technicians and the proper tools to service

or repair this unit.

Please read and retain this manual. The instructions

will enable you to assemble and maintain your

mower properly° Always Observe the "SAFETY

RULES".

MODEL

NUMBER 917.380221

SERIAL

NUMBER

DATE OF

PURCHASE

THE MODEL AND SERIAL NUMBERS WILL BE

FOUND ON A DECAL ATTACHED TO THE REAR

OF THE MOWER HOUSING_

YOU SHOULD RECORDBOTHSERIALNUMBER

AND DATEOFPURCHASEAND KEEPIN A SAFE

PLACEFOR FUTUREREFERENCE.

i ,i

MAINTn:NANCEAGREEMENT

A Sears Maintenance Agreement isavailable on this

producL Contact your nearest Sears store for

details.

CUSTOMERRESPONSgBILITIES

PRODUCTSPEaFICATHOHS

' ' i,, ,11

RESERVE POWER: 3.5

.............. ,,,ml , i

DISPLACEMENT: 9.06 cu. in.

I I1'1 i,, i],, ]11]!,11,11 ,,i,,,i,,i,1,,,, ,i ...........

GASOLINE CAPACITY: 1.0 quart,

................. (unleaded)

OIL (21 oz, capacity): SAE 30W

(SAElow 30)

, ,ijlj jl,lll

SPARK PLUG (GAP ,030 in.) Champion

RJ19-LL or

(Sears 7133312 or

STD361458)

VALVE CLEARANCE: Intake: _008 in_

Exhaust: .008 ino

SOLID STATE IGNITION

AIR GAP:

I II [II I I I I ,i i,ii1,1,1,1_1111111111,11,,

BLADE NUT TORQUE:

.0125 in.

70-75 ft0-1bs_

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for and using your mower.

Follow the instructions under "Maintenance" and "Storage" sections of this Owner's Manual_

............... _,,,,,,_,,,,,,,,,,,_ ,_Ll_,, iill uiili,uu

ONEYEARLIMITEDWARRANTYON CRAFTSMANPOWERMOWER

Forone year fromthe date of purchase, when thisCraftsmanLawn Mower ismaintained, lubricated and tuned-up.

according to the instructionsin the owner's manual, Sears will repair, free of charge, any defect in material

and worEmanship_

If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90

days from the date of purchaser

Thiswarranty does not cover:

Expendable itemswhich become worn during normal use, such as rotary mower blades, blade adapters,

belts, air cleaners and spark plug.

Repairs necessarybecause of operator abuse or negligence, including bent crankshafts and the failure to

maintain the equipment according to the instructionscontained in the owner's manual°

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN POWER MOWER TO THE

NEAREST SEARS SF:RVlCECENTERIDEPARTMENT IN THE UNITED STATES. THIS WARRANTY APPLIES

ONLY WHILE THIS PRODUCT IS IN USE IN THE UNITED STATES°

Thiswarranty gives you specificlegal rights, and you may also have other rights which may vary from state

to state_

SEARS, ROEBUCK AND CO, Department 698/731A Sears Tower, Chicago, Ill. 60684

TABLEOFCONTENTS

SAFETY RULE ......................

PRODUCT SPECIFICATIONS ...........

CUSTOMER RESPONSiBiLITIES .......

WARRANTY ...............

TABLE OF CONTENTS

INDEX ...................

MOWER ACCESSORIES ......

ASSEMBt.Y .....

OPERATION ................

6,7,8

MAINTENANCE .................... 8,9,10

STORAGE .......................... 12

SERVICE AND ADJUSTMENT .......... 10,1 t

TROUBLE SHOOTING .................... t 9

REPAIR PARTS-MOWER ............. 14,15

REPAIR PARTS-ENGINE .......... t 6,17,18 ,,

SERVICE RECOMMENDATIONS .......... 13

PARTS ORDERING/SERVICE ....... 20

INDEX

Adjustments:

Carburetor

Engine Speed

Handle Height

Height of Cut

Wheel Adjusters

Air Filter:

Cleaning _.

Paper Cartridge

Replacement

Assembly:

Handle

Accessories

Blade:

Replacement

Sharpening

Controls:

Engine Control

Operator Presence

Control Bar

Speed Selector ....

Customer Responsibilities

Cutting Levels

Engine:

Control

Oil Cap

Oil Change

Oil Level

Oil Type

Starting

Storage

Filter, Air

Fuel:

Type

Storage

Gasoline

7Handle:

Adjustment

g,10 Assembly

10 Bracket

10 Knob

Height, Cu|ting

5.6.7

8.9

6,7

6,9

9,t0

index

7,t 1

Lubrication:

Engine 13

Front Wheel Adjuster 7

Maintenance:

Agreement .... 3

Air Filter _ g, 10

Air Filter Paper Cartrldge 10

Blade Care/Replacement 8.9

Engine g

Grass Catcher' .9

Lubrication 13

Spark Plugs 3,10

Mowing Tips 8

3 Parts t4,15

Primer 7

Oil:

Cold Weather Conditions 7

Engine ,9

Storage 12

Operation:

Operating Mower 6,7 8

Speed:

Starting the Engine 7

Stopping Your Lawn Mower 7

Operator PresenceControl

Options:

Attachments 5

RepairtReplacement Parts 14 15

Responsibilities,Customer 3

Safety Rules 2

Service and Adjustments:

Blade .... 8,9

Carburetor 10

Cutting Level 7

Engine . ,7

Handle 11

Service Recommendation 13

Spark Plugs 3,10

Specifications 3

Speed Control:

Engine = 7

Starling the Engine:

Starter Rope 6

Stopping the Mower .7

Storage t 2

Table of Contents . _4

Trouble Shooting Chart !9

Warranty

Wheels:

Wheel Adjuster's

MOWER

These accessories were available when the mower was purchased° They are also available at most Sears retail

outlets, catalog and service centers. Most Sears stores can order repair parts for you, when you provide the

model number of your mower.

ENGINE

SPARKPLUG MUFFLER

©AIR FILTER GASCAN EHGIHEOIL STABILIZER

MOWERMAiNTENANcE........................................................................................................................................................................................................................................................

BELT BLADE BLADEADAPTER WHEELS MOWERCOVER

ASSEMBLY

Your lawn mower has been completely assembled

at the factory°

TO REMOVEMOWERFROMCARTON

• Remove loose parts if included with mower, (i.e.

grass catcher, catcher frame, hardware pack,

etc,)_

o Cut down corners on one end of carton and lay

end down flat.

o Remove packing material,

o Roll mower out of carton and check carton

thoroughly for loose parts.

HOWTOSET-UPYOURLAWNMOWER

TO UNFOLDHANDLE

OPERATOR PRESENCE -

7.€, "t'

UPPER HANDLE---_ _."/ •

LIFT UP .//'// _// •._/

• Wt

/,-%.,,,.y.:},....J

{Wi":-",:_.,-r.._--:,_\,_,75), r,,oW_N_resmo.

LOWER HANOLE

............ ::; _,,,_ _'_'"/'" ,i,'.:;,_ ........... H±

FIG. I

Remove tape and paper holding operator presence

control bar to upper handle°

•Hold down operator presence control bar to up-

per handle to allow handle to move to mowing

position.

,Raise handles until lower handle section locks in-

to place in the mowing position (See Fig. I).

Raise upper handle section intoplace on lower

handle and tighten one (1) handle knob°

Release operator presence control bar and

tighten remaining handle knob°

•Your mower handle can be adjusted for your

mowing comfort. Refer to "ADJUST HANDLE"

in the Service and Adjustment section of this

manual.

OPERATION

KNOWYOURMOWER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR ROTARY MOWER°

Compare the illustrations with your Rotary Mower to familiarize yourself with the location of various controls

and adjustments. Save this manual for future reference.

)PERATOR PRESENCE CONTROL BAR

ZONE/ENGINE

CONTROL.

HANDLE KNOB - CABLE CLIP

STARTER ROPE ENGINE OIL CAP WITH DIPSTICK

ENGINE SPEED

SELECTOR LEVER FILLER CAP

MUFFLER

PRIMER WHEEL ADJUSTER

DISCHARGE

AIR FILTER

MEETSCPSCSAFETYREQUIREMENTS

HOUSING

Sears Rotary Walk-Behind Power Mowers conform to the safety standards of the American National Stan-

dards Institute and The U.S. Consumer Product Safety Commission, The blade turns when the engine is running,

IIIIII1'1 I I ' '

OPERATOR PRESENCE CONTROL BAR - must be

held down to the handle to start the engine, Release

to stop the engine,

ENGINE SPEED CONTROL LEVER - located on the

right side of the engine which allows you to select

either "HIGH" or "LOW" engine speed_

PRIMER - pumps additional fuel from the carburetor

to the cylinder for use when starting a cold engine.

STARTER ROPE - used for starting the engine.

HOWTOUSEYOURMOWER

ENGINESPEEOSELEaOR

The en_line speed is controlled by a lever (red knob)

tocatedon the right side of theengine. "HIGH" posi-

tion is for starting engine, normal cutting and better

grass bagging. "LOW" position isfor light cutting,

trimming, and fuel economy (See Fig. 3).

TO ADJUST CUTTING HEIGHT

=Raise wheels for low cut and lower wheels for

high cut.

° Wheels are set in low cut for shipping. Adjust cut-

ting height to suit your requirements. Medium

position is best for most lawns.

o To change cutting height, squeeze adjuster lever

toward wheel Move wheel up or down to suit

your requirements° Be sure all wheels are in the

same setting (See Fig. 4).

SELECTOR LEVER

1ER

.....................................-: IG.3.......................................................................

BEFORESTARTINGENGINE

OIL:

• Remove engine oil cap with dipstick or oil fill plugo

Fill to "FULL" line on dipstick or to top of slot

clown in filler hole. Use about I pint or 1!2 liter

of Sears 30W oil or equivalent. SAE 10W 30 oil

can also be used. DO NOT use SAE 10W 40 oil.

The total oil capacity of your engine is 21 oz. or

0.62 liters. Fill only to "FULL" line on dipstick or

to top of slot down in oil filler holeo

DO NOT over fill. The first fill on a new engine

uses about 1 pint. Check oil level and add oil as

needed to bring to proper level.

• Pour oil slowly, DO NOT over fill.

GAS:

* Fill gasoline tank with fresh, clean unleaded

gasoline. DO NOT USE PREMIUM GASOLINE.

BE CAREFUL NOT TO OVER FILL TANK (SEE

FIG. 2)_

WARNING: Experience indicates that alcohol blend-

ed fuels (called gasohol or usingethanol or methanol)

can attract moisture which leads to separation and

formation of acids during storage_ Acidic gas can

damage the fuel systemof an engine while in storage.

To avoid engine problems, the fuel system shouldbe

emptied before storage for 30 days or longer. Drain

the gas tank, start the engine and let it run until the

fuel/ines and carburetor are empty. Use fresh fuel

FIG, 4

next season. See Storage Instructions for additional

informatiom

Never use engine or carburetor cleaner products in

the fuel tank or permanent damage may occur.

TO STARTENGINE

= To start a cold engine, push primer five (5) times

before trying to start. Use a firm push. This step

isnot usually necessary when starting an engine

which has already run for a few minutes.

* Push engine speed selector lever forward to

"HIGH" position.

* Hold operator presence control bar down to the

handle and pull starter handle quickly. Do not

allow starter rope to snap back.

* To "STOP" engine, release operator presence

control bar.

NOTE: In cooler weather it may be necessary to

repeat priming steps. In warmer weather over prim-

ing may cause flooding and engine wilt not start° If

you do flood engine wait a few minutes before at-

tempting to start and DO NOT repeat priming steps.

MOWINGTIPS OPERATION

IPIIII '1

,' Under certain conditions, suchas very tall grass,

it may be necessary to raise the height of cut to

reduce pushing effort and to keep from

overloading the engine and leaving clumps of

grass clippings_

* For extremely heavy cutting, reduce the width of

cut and raise the rear of the mower housing one

(I) wheel adjuster setting higher than the front for

better discharge of grass_

oWhen using a rear bagging mower in moist,

heavy grass, clumps of cut grass may not enter

the grass catcher. Reduce groundspeed (pushing

speed) andlor run the mower over the area a seo

cond time.

* For better' grass bagging and most cutting con-

ditions, the engine speed should be set in the

"HIGH" (fast) position.

•If a trail of grass clippings is left on the right side

of a rear bagging mower, mow in a clockwise

direction with a small overlap to collect the clip-

pings on the next pass. -

', For' side discharge mowers, cutting in a counter-

clockwise direction, starting at the outside of the

area to be cut, spreads grass clippings more even-

ly and puts lessload on the engine. To keep clip-

pings off of walkways, flower beds, etc., make

the first cuts in aclockwise direction.

• Pores in cloth grass catchers can become filled

with dirt and dust with use and catchers will col-

lect less grass. To prevent this, regularly hose cat-

cher off with water and let dry before using.

MAINTENANCE J[ll][I IJ

...........I, I,I II .....

MOWER

GENERALRECOMMENDATIONS

•Once a year you should replace the spark plug,

air filter, and check blade for wear. A new spark

plug and air' filter assures proper' air-fuel mixture

andhelps your engine run better and last lon_er_

• You should check all fasteners and be sure they

are tight°

• Follow the Service Recommendation Schedule on

page 13_

BLADE/BLADEFLANGECARE

Your mower will work better with a sharp blade.

_ CAUTION: DISCONNECTSPARKPLUGWIREFROM

SPARKPLUGANDPLACEWIREWHEREIT CANNOT

COMEIN CONTACTWITH THESPARKPLUG.

1"O REMOVE BLADE:

"Turn mower on its side. Make sure air filter and

carburetor are up.

•Use block of wood between blade and mower

housing to prevent blade from turning when nut

isremoved. Protect your hands with gloves and/or

wrap blade with heavy cloth.

• Remove nut by turning counter-clockwise. Use a

15116" box or open-end wrench.

I'IIIII'I'I'IM IIII" '1" .............................

'11'11'111IIII III'1'11i IIIII

CRANKSHAFT & _/" \\

BLADE FLANGE I// / \\

DETAIL _/\\_

/iL-LtSLtD

BLA°EwAs"ERs E

,LADEF.AHO,

,,nilI.................

FIG. 5

NOTE: Check tab in blade flange after removing_ If

tab is damaged, replace it. It must be in good con-

dition for' the blade to work properly. We recom_

mend that a new blade nut be used each time blade

is removed.

TO REPLACE BLADE:

• Put blade flange on engine crankshaft with tab

in slot (See Fig_ 5).

•Fit blade on crankshaft in the blade flange. Be

sure the word "TOP" (stamped on blade) is

toward engine.

•Place flat washer, two (2) formed washers and

nut on crankshaft (See Fig. 5).

•Use block of wood to hold blade and tighten nut

clockwise. The recommended torque is 70-75 ft..

Ibs. Torque wrenches are available at most Sears

stores and through the catalog.

MOWER

BLADE/BLADEFLANGE CARE (CONT'D)

CAUTION:ALOOSEBLADECANBEDANGEROUS

bANDMAY NGINE,A D START.

Use only a Sears authorized replacement blade to

get the best cutting results.

NOTE: We do not recommend Sharpening blade - but"

if you do, be sure the blade is balanced°

CONTAINER

TO SHARPEN BLADE:

oThe blade can be sharpened with a file or on a

grinding wheel. Do not attempt to sharpen while

on the mower.

• Care should be taken to keep the blade balanc-

ed. An unbalanced blade will cause excessive

vibration when running and eventual damage to

mower or engine.

o To check blade balance, drive a nai! into a beam

or wall. Leave about one inchof the straight nail

expose& Place center hole of blade over the head

of the nail. If blade is balanced, it should remain

in a horizontal position. If either end of the blade

moves downward, blade is not balanced.

Sharpen the heavy end until the blade is

balance&

GRASSCATCHER

(If Purchased As An Accessory)

Check your grass catcher often for damage or

deterioration° Through normal use it will wear, tf cat-

cher needs replacing, replace only with a maufac-

turer approved replacement catcher from Sears.

Give the mower model number when ordering.

NOTE: The catcher may be hosed with water, but must

be dry when used.

ENGINE

TO CHANGEOIL

CAUTION: DISCONNECT SPARK PiU'; w"i

d_ FROMSPARKPLUGAND PLACEWIRE WHEREIT

CANNOTCOMEIN CONTACTWITH SPARKPLUG. •

_U_.L JLLJJ L...........4L ............................................. ,,,,,,,,.... ,, ...................... ________: ..............

FIG. 6

o TiE)mower on its side as shown in Fig. 6 and drain

oi/into suitable container. Rock mower back and

forth to remove any oi! trapped inside of engine.

• Wipe off any spilled oil on mower and on side

of engine°

•Fill engine with oil. Fill only to the "FULL" line

on the dipstick. DO NOT over fill.

• Replace engine oil cap. "

• Reconnect spark plug wire to spark plug.

AIR FILTER

Your engine will not run properly and may be

damaged by using a dirty air filter.

Replace the air filter every year, more often if you

mow in very dusty, dirty conditions° Do not wash air

filter.

TO CHANGE AIR FILTER:

o Remove the air filter cover by turning

counterclockwise to the stop and pull away from

collar (See Fig. 7).

• Remove filter from inside of cover (See Fig, 7),

• Clean the inside of the cover and the collar to

remove any dirt accumulation.

• insert new filter into cover.

o Remove engine oil cap with dipstick; lay aside on

a clean surface. Warm oil drains better.

i,ll i, i1!11ii ..............

MAINrENANCE

AIR FILTER(CONT'D)

•Put air filter cover and filter into collar aligning

the tab with the slot.

• Pushin on cover and turn clockwise to tighten (See

Fig. 7).

SPARKPLUG

Change your spark plug each year to make your

engine start easier and run better. Set spark plug

gap at _030 inch.

COLLAR

I IIIlllllllllllII

CLEANING

d_CAUTION: DISCONNECTSPARKPLUGWIRE FROM

SPARKPLUGAND PLACEWIREWHEREIT CANNOT

COMEIN CONTACTWITH THESPARKPLUG.

=Turn mower on its side with carburetor upo

=Clean the underside of your mower by scraping

to remove build-up of grass and trash.

NOTE: We recommend that you clean the underside

of your mower after each use.

Illll IIIII

SLOT

COUNTER-

CLOCKWISE

TO REMOVE

AIR FILTER

TURN CLOCKWISE

TO TIGHTEN

A_RF1LTERCOVER

FIG. 7

Clean your mower' and engine often to keep build-

up of trash from accumulating around engine. A

clogged engine runs hotter and shortens engine.

lifeo

NOTE: We DO NOT recommend using a garden hose

to clean mower unlessthe electrical system, muffler,

air filter, and carburetor are covered to keep water

out. Water in engine can result in shortening engine

life.

CARBURETOR

,_, "I'L'IIL'_.................................. III 'l

SERVICEANDADJUSTMENTS

I'll '11........................... I I I ..................................................

Your carburetor has a non-adjustable fixed main jet

for mixture controi_ If your engine does not operate

properly due to suspected carburetor problems, take

your mower to an authorized Sears Service Center

for repair and adjustment_

possibility of injury resulting from objects being

thrown out of the discharge opening into theoperator

mowing position.

if the discharge guard becomes damaged, it should

be replaced.

ENGINESPEED

Your engine speed has been factory set. Do not at-

tempt to increase engine speed or it may result in per-

sonal injury. If you believe that the engine is runn-

ing too fast or too slow, take your mower to an

authorized Sears Service Center for repair and

adjustment.

DISCHARGEGUARD

The discharge guard, attached to the discharge

opening of your mower, ts provided to prevent the

REARDEFLECTOR

The rear deflector, attached between the rear wheels

of your mower, isprovided to minimize the possibility

that objects will be thrown out the rear of the mower

into the operator mowing position.

If the rear deflector becomes damaged, it should be

replaced.

Andere Craftsman Rasenmäher Handbücher

Craftsman

Craftsman 917.388894 Bedienungsanleitung

Craftsman

Craftsman 247.388240 Bedienungsanleitung

Craftsman

Craftsman 917.376672 Bedienungsanleitung

Craftsman

Craftsman 917.275764 Bedienungsanleitung

Craftsman

Craftsman 917.272350 Bedienungsanleitung

Craftsman

Craftsman EZ 917.273014 Bedienungsanleitung

Craftsman

Craftsman 917.374550 Bedienungsanleitung

Craftsman

Craftsman 27726 Bedienungsanleitung

Craftsman

Craftsman 917.378170 Bedienungsanleitung

Craftsman

Craftsman 917.371030 Bedienungsanleitung

Craftsman

Craftsman 917.377794 Bedienungsanleitung

Craftsman

Craftsman 917.288320 Bedienungsanleitung

Craftsman

Craftsman 502.255091 Bedienungsanleitung

Craftsman

Craftsman 944.361330 Bedienungsanleitung

Craftsman

Craftsman 27740 Bedienungsanleitung

Craftsman

Craftsman 917.374358 Bedienungsanleitung

Craftsman

Craftsman 917.377664 Bedienungsanleitung

Craftsman

Craftsman 25112 Bedienungsanleitung

Craftsman

Craftsman 917.378411 Bedienungsanleitung

Craftsman

Craftsman 917.271662 Bedienungsanleitung

Craftsman

Craftsman 25911 Bedienungsanleitung

Craftsman

Craftsman 917.371840 Bedienungsanleitung

Craftsman

Craftsman 917.377041 Bedienungsanleitung

Craftsman

Craftsman 2One 917.372471 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung