Craftsman 917.387254 Bedienungsanleitung

Owner's Manual

rRilFTXMIIN °

4.0 HORSEPOWER

20" REAR DISCHARGE

ROTARY LAWN MOWER

Model No.

917.387254

• Safety

•Assembly

•Operation

• Maintenance

•EspaSol

•Repair Parts

CAUTION:

Read and follow all

Safety Rules and Instructions

before operating this equipment

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Warranty 2 Product Specifications 9

Safety Rules 2 Service and Adjustments 11

Assembly 4 Storage 13

Operation 5 Troubleshooting 14

Maintenance Schedule 8 Repair Parts 30

Maintenance 8 Parts Ordering Back Cover

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN POWER MOWER

For one year from date of purchase, when this Craftsman Lawn Mower is maintained,

lubricated, and tuned up according to the operating and maintenance instructions in the

owner's manual, Sears will repair free of charge any defect in material or workmanship.

If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty

applies for only 90 days from the date of purchase.

This Warranty does not cover:

• Expendable items which become worn during normal use, such as rotary mower

blades, blade adapters, belts, air cleaners and spark plug.

• Repairs necessary because of operator abuse or negligence, including bent crank-

shafts and the failure to maintain the equipment according to the instructions con-

tained in the owner's manual.

Warranty service is available by retuming the Craftsman power mower to the nearest

Sears Service Center/Department in the United States. This warranty applies only while

this product is in use in the United States.

This Warranty gives you specific legal rights, and you may also have other rights which

vary from state to state.

SEARS, ROEBUCKAND CO., D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179

TRAINING:

•Read this operator's manual carefully.

Become familiar with the controls and

know how to operate your mower

properly. Learn how to quickly stop

mower.

•Do not allow children to use your mower.

Never allow adults to use mower without

proper instructions. _

•Keep the area of operation clear of all

persons, especially small children and

pets.

•Use mower only as the manufacturer

intended and as described in this manual.

•Do not operate mower if ithas been

dropped or damaged in any manner.

Always have damage repaired before

using your IPower.

•Do not use accessory attachments that

are not recommended by the manufac-

turer. Use of such attachments may be

hazardous.

• The blade turnswhen the engine is

running.

PREPARATION:

•Always thoroughly check the area to be

mowed and clear it of all stones, sticks,

wires, bones, and other foreign objects.

These objects willbe thrown by the blade

and can cause severe injury.

•Always wear safety glasses or eye

shields when starting and while using

your mower.

•Dress properly. Do not operate mower

when barefoot or wearing open sandals.

Wear only solid shoes with good traction

when mowing.

•Check fuel tank before starting engine.

Do not fill gas tank indoors, when the

engine is running or when the engine is

hoLAllowtheenginetocoolforseveral

minutesbeforefillingthegastank.Clean

offanyspilledgasolinebeforestartingthe

engine.

•Always make wheel height adjustments

before starting your mower. Never

attempt to do this while the engine is

running.

• Mow only in daylight or good artificial

light.

OPERATION:

•Keep your eyes and mind on your mower

and the area being cut. Do not let other

interests distract you.

•Do not mow wet or slippery grass. Never

run while operating your mower. Always

be sure ofyour footing -- keep a firm

hold on the handles and walk.

•Do not put hands or feet near or under

rotating parts. Keep clear of the discharge

opening at all times.

•Always stop the engine whenever you

leave or are not using your mower, or

before crossing driveways, walks, roads,

and any grevel_covered areas.

•Never direct discharge of material toward

bystanders nor allow anyone near the

mower while you are operating it.

•Before cleaning, inspecting, or repairing

your mower, stop the engine and make

absolutely sure the blade and all moving

parts have stopped. Then disconnect the

spark plug wire and keep itaway from the

spark plug to prevent accidental starting.

•Do not continue to run your mower if you

hit a foreign object. Follow the procedure

outlined above, then repair any damage

before restarting and operating you

mower.

• Do not change the governor settings or

overspeed the engine. Engine damage or

personal injury may result.

• Do not oPerate your mower if it vibrates

abnormally. Excessive vibration is an

indication of damage; stop the engine,

safely check for the cause of vibration

and repair as required.

• Do not run the engine indoors. Exhaust

fumes are dangerous.

•Never cut grass by pulrmgthe mower

towards you. Mow across the face of

slopes, never up and down or you might

lose your footing. Do not mow exces-

sively steep slopes, Use caution when

operating the mower on uneven terrain

or when changing directions -- maintain

good footing.

• Never operate your mower without

proper guards, plates, grass catcher or

other safety devices in place.

MAINTENANCE AND STORAGE:

•Check the blade and the engine mount-

ing bolts often to be sure they are

tightened pmpedy.

•Check all bolts, nuts and screws at

frequent intervals for proper tightness to

be sure mower is in safe working

condition.

• Keep all safety devices in place and

working.

•To reduce fire hazard, keep the engine

free of grass, leaves or excessive grease

and oil.

•Check grass catcher often for detedora-

tion and wear and replace worn bags.

Use only replacement bags that are

recommended by and comply with

specifications of the manufacturer of your

mower.

•Always keep a sharp blade on your

mower.

•Allow engine to cool before storing in any

enclosure.

•Never store mower with fuel in the tank

inside a building where fumes may reach

an open flame or an ignitionsource such

as a hot water heater, space heater,

clothes dryer, etc.

CAUTION: Always disconnect spark plug

wire and place wire where it cannot

contact spark plug in order to prevent

accidental starting when setting up,

transporting, adjusting or making repairs.

WARNING

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

These accessories were available when this lawn mower was produced. They are also

available at most Sears retailoutlets and service centers. Most Sears stores can also order

repair parts for you, when you providethe model number ofyour lawn mower. Some ofthese

accessoriesmay not applyto yourlawn mower.

LAWN MOWER PERFORMANCE

cUpPING DEFLECTOR

FOR REAR DISCHARGE LAWN MOWERS

GRASS CATCHERS

FOR

REAR DISCHARGE

LAWN MOWERS

M_CH_KITS

_GRASS CATCHERS

/FOR

SIDE DISCHARGE

LAWN MOWERS

STABIUZER

GAS CANS

LAWN MOWER MAINTENANCE

MUFFLERS AIR RLTERS SPARK PLUGS

BELTS BLADES BLADE ADAPTERS WHEELS ENGINE OIL

Read these instructions and this manual

in its entirety before you attempt to

assemble or operate your new lawn

mower, Your new lawn mower has been

assembled at the factory with the excep-

tion of those parts left unassembled for

shipping purposes. All parts such as nuts,

washers, bolts, etc., necessary to com-

plete the assembly have been placed in

the parts bag. To ensure safe and proper

operation of your lawn mower, all parts

and hardware you assemble must be

tightened securely. Use the correct tools

as necessary to ensure proper tightness.

TO REMOVE LAWN MOWER FROM

CARTON

•Remove loose parts included with

mower.

•Cut down two end corners of carton

and lay end panel down flat.

•Remove all packing materials except

padding between upper and lower

handle and padding holding operator

presence control bar to upper handle.

•Roll lawn mower out of carton and

check carton thoroughly for additional

loose parts.

HOW TO SET UP YOUR LAWN

MOWER

TO UNFOLD HANDLE

IMPORTANT: Unfold handles carefully

so as not to pinch or damage control

cables.

•Raise handles until lower handle

section locks into place in mowing

position.

•Remove protective padding, raise upper

handle section into place on lower

handle and tighten both handle knobs.

•Remove handle padding holding

operator presence control bar to upper

handle.

•Your lawn mower handle can be

adjusted for your mowing comfort.

Refer to "Adjust Handle" in the Service

and Adjustment section of this manual.

Operator presencecontrolbar

Upperhandle,

Liftup

Mowing

position

Lowerhandle

KNOW YOUR LAWN MOWER

READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR LAWN

MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the

location of various controls and adiustments. Save this manual for future reference.

These symbols may appear on your lawn mower or in literature supplied with the

product. Learn and understand their meaning.

CAUTION ENGINE ENGgNE FAST SLOW CHOK E FUEL O_L DANGER, KEEP HANDS

OR WARlY4NG ON OFF AlyO FEET AWAY

Engine zone control....

cable Dperatorpresence controlbar

Starter handle

Handle kno'

Grass catcher,

_ap

Air filter

Primer

Lawn mowerhousing

Engine oil plug Wheel ajduster

(on each wheel)

MEETS CPSC SAH-TY' REQUIREMENTS

Sears rotary walk-behind power lawn mowers conform tothe safety standards ofthe American

National Standards Instituteand the U.S. Consumer ProductSafety Commission. The blade

turns when the engine isrunning.

uperator presence cu,_t,ul Par - must De Primer - pumps additional fuel fromthe

held down to the handle tostartthe engine, carburetor to the cylinderfor use when starting

Release tostop the engine, a cold engine.

Starter handle -used for starting the engine.

The operation of any lawn mower can

result in foreign objects thrown into the

eyes. which can result in severe eye

damage. Always wear safety glasses or

eye shields while operating your lawn

mower or performing any adjustments or

repairs. We recommend a wide vision

safety mask over spectacles or standard

safety glasses.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED CONTROL

The engine speed was set at the factory

for optimum performance. Speed is not

adjustable.

ENGINE ZONE CONTROL

CAUTION: Federal regulations require an

engine control to be installed on this lawn

mower in order to minimize the risk of

blade contact injury. Do not under any

circumstances attempt to defeat the

function of the operator control, The blade

turns when the engine is running.

•Your lawn mower is equipped with an

operator presence control bar which

requires the operator to be positioned

behind the lawn mower handle to start

and operate the lawn mower,

TO ADJUST CUTTING HEIGHT

•Raise wheels for low cut and lower

wheels for high cut.

•Adjust cutting height to suit your

requirements. Medium position is best

for most lawns.

•To change cutting height, squeeze

adjuster lever toward wheel. Move

wheel up or down to suit your require-

ments. Be sure all wheels are in the

same setting.

NOTE: Adjuster is properly positioned

when plate tab inserts into hole in lever.

TO ATTACH GRASS CATCHER

•Close the flip lid. Flip lid must be closed

while operating lawn mower.

•Lift the rear door on the mower housing

and place the grass catcher frame onto

the formed tabs on the rear door hinge

bracket.

•The grass catcher is secured to the lawn

mower housing when the rear door is

lowered onto the grass catcher frame.

CAUTION: Do not run your lawn mower

without clipping deflector or approved

grass catcher in place. Never attempt to

operate the lawn mower with the rear door

removed or propped open.

bracket

Formed

tabs

Grass

frame

TO EMPTY GRASS CATCHER

•To remove grass catcher, release

operator presence control bar to stop

engine.

•Lift up rear door and remove the grass

catcher by the handle.

NOTE: Do not drag the bag when

emptying; it will cause unnecessary wear.

Lowerwheels for

higttcut 'cutr_j_

<_ Lever

Plate tab

•Pour oil slowly. Do not over fill.

•Be sure mower is level and area around

oil fill is clean.

•Remove engine oil plug and fill to the full

line on the dipstick.

•Use 20 ozs. of oil. For type and grade

of oil to use, see =ENGINE" in Mainte-

nance section of this manual.

Also, 9-position adjustoes (if so equipped) E

allow lever to be_rmdbetween,the ::, _EFORIE ST_ NGINE

plate :tabs., _.... _OIL :

Yourlawn mower is,shipped without oil in

Raise wheels fot4ow :,"the engine;

•Check oil level before each use. Add oil

if needed. Fill to full line on dipstick.

• To read proper level, tighten engine oil

plug each time.

•Reinstall engine oil plug and tighten.

•Change the oil after every 25 hours of

operation or each season. You may

need to change the oil more often under

dusty, dirty conditions.

GAS

• Fill fuel tank. Use fresh, clean, regular

unleaded gasoline with a minimum of 87

octane. (Use of leaded gasoline will

increase carbon and lead oxide deposits

and reduce valve life). Do not mix oil

with gasoline. Purchase fuel in quanti-

ties that can be used within 30 days to

assure fuel freshness.

WARNING: Experience indicates that

alcohol blended fuels (called gasohol or

using ethanol or methanol) can attract

moisture which leads to separation and

formation of acids during storage. Acidic

gas can damage the fuel system of an

engine while in storage. To avoid engine

problems, the fuel system should be

emptied before storage of 30 days or

longer. Drain the gas tank, start the

engine and let it run until the fuel lines and

carburetor are empty. Use fresh fuel next

season. See Storage Instructions for

additional information. Never use engine

or carburetor cleaner products in the fuel

tank or permanent damage may occur.

Gasolinefiller

cap

Engine oil

TO START ENGINE

•To starta coldengine, pushprimer five (5)

times beforetryingtostart. Use afirm push.

This step isnot usuallynecessary when

starting an engine which has already runfor

afew minutes.

•Hold operatorpresence control bar down to

the handle and pullstarter handle quickly.

Do not allowstarterropeto snap back.

•To stop engine, release operatorpresence

control bar.

NOTE: In coolerweather itmay be necessary

to repeat primingsteps. Inwarmer weather

over primingmay cause floodingand engine

willnotstart, ffyou do floodengine, wait a few

minutes beforeattemptingto start and do not

repeat primingsteps.

MOWING TIPS

•Under certain conditions, such as very

tall grass, it may be necessary to raise

the height of cut to reduce pushing effort

and to keep from overloading the engine

and leaving clumps of grass clippings. It

may also be necessary to reduce

ground speed and/or run the lawn

mower over the area a second time.

•For extremely heavy cutting, reduce the

width of cut by overlapping previously

cut path and mow slowly.

•For better grass bagging and most

cutting conditions, the engine speed

should be set in the fast position.

•When using a rear discharge lawn

mower in moist, heavy grass, clumps of

cut grass may not enter the grass

catcher. Reduce ground speed (push-

ing speed) and/or run the lawn mower

over the area a second time.

•If a trail of clippings is left on the right

side of a rear discharge mower, mow in

a clockwise direction with a small

overlap to collect the clippings on the

next pass.

•Pores in cloth grass catchers can

become filled with dirt and dust with use

and catchers will collect less grass. To

prevent this, regularly hose catcher off

with water and let dry before using.

•Keep top of engine around starter clear

and clean of grass clippings and chaff.

This will help engine air flow and extend

engine life.

MAINTENANCESCHEDULE

FILL IN DATES

AS YOU COMPLETE

REGULAR SERVICE

Check for Loose Fasteners t_

Cleardlr',spect Grass Catcher

M CleanLawnMower

_Clean Under Drive Cover

(Power-Propelled Mowers) IV/

Checkdrivehalt/pulleys

E (Power-propened Mowers) I_

CheclVSharpen/Replace Blade _ 3

Lubrication Chad I/ I_

Clean Battery/Recharge

Electric Start Mowers/M I/'4

ECheck Engine Oil Level t/

Change Engine Oil IVtl.2

Clean Air Filter Ii/ 2

I Inspect Muffler I_

N c_an orReplaceSparkPlug !/

E ReplaceAirFilterPaperCartridge I/'2

SERVICE DATES

1 - Change more olten when operaUngundera heavy loado{ in highambienttemperatures.

2-Sowice more oftenwhen opetaling indirtyo_dusty_.

3. Replace blade=more olten v+henmow_g _sandy sdiL

4 - Charge 48 hours at end of season. LUBRICATION CHART

GENERAL RECOMMENDATIONS

The warranty on this lawn mower does not

cover items thathave been subjectedto

operator abuse or negligence. To receive full

value from the warranty, operatormust

maintain mower as instructedinthis manual,

Some adjustments willneed tobe made

periodically to properly maintain your unit.

All adjustments in the Service and Adjust-

ments section of this manual should be

checked at least once each season.

• Once a year, replace the spark plug, replace

air filter element and check blade for wear.

A new spark plug and clean/new air filter

element assures proper air-fuel mixtureand

helps your engine runl_etter and last longer.

•Followthe maintenance schedule inthis

manual.

Wheel

(_Rrea/

door

(3:) hinge

Handlebracket

(_ Brake springe

bracket

(_) Engine oil

BEFORE EACH USE

•Check engine oil level.

• Check for loose fasteners.

LUBRICATION

Keep unitwell lubricated (See "LUBRICATION

CHART').

(_ Spray lubricant

SAE 30 Motoroil. Refer to ENGINE

(_ MAINTENANCE Section.

IMPORTANT: Do not oil or grease plastic

wheel bearings. Viscous lubricants will

attract dust and dirt that will shorten the life

of the self lubricating bearings. If you feel

they must be lubricated, use only adry,

powdered graphite type lubricant sparingly.

PRODUCT SPECIFICATIONS

MODEL NUMBER 917.387254

SERIAL NUMBER

DATE OF PURCHASE

HORSEPOWER: 4.0

DISPLACEMENT: 11.5 CU. IN.

GASOLINE CAPACITY/TYPE: 1.25 QUARTS

UNLEADED REGULAR

OIL TYPE (APIoSF/SG/SH): SAE 30 (ABOVE 32°F)

SAE 5W-30 (BELOW 32°F)

OIL CAPACITY: 20 OZS.

SPARK PLUG(GAP: .030") CHAMPION RJ19LM OR J19LM

VALVE CLEARANCE: INTAKE: .004 -.008

EXHAUST: .004 - .008

SOLID STATE IGNITION

AIR GAP: .0125 IN.

BLADE BOLT TORQUE: 35-40 FT. LBS.

The model and serial numbers will be found on a decal attached to the rear of the

lawn mower housing.Record both serial number and date of purchase in space

provided above.

LAWN MOWER • Remove blade and attaching hardware

(bolt, lock washer and hardened

washer).

NOTE: Remove the blade adapter and

check the key inside hub of blade adapter.

The key must be in good condition to work

propedy. Replace adapter if damaged.

Always observe safety rules when

performing any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect

control chemicals which can harm

rubber.

•Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may

cause tire damage.

BLADE CARE

For best results, mower blade must be

kept sharp. Replace bent or damaged

blades.

TO REMOVE BLADE

• Disconnect spark plug wire from spark

plug and place wire where it cannot

come in contact with spark plug.

• Turn lawn mower on its side. Make sure

air filter and carburetor are up.

• Use a wood block between blade and

mower housing to prevent blade from

turning when removing blade bolt.

• Protect your hands with gloves and/or

wrap blade with heavy cloth.

• Remove blade bolt by turning counter-

clockwise.

TO REPLACE BLADE

• Position the blade adapter on the engine

crankshaft. Be sure key in adapter and

crankshaft keyway are aligned.

• Position blade on the blade adapter

aligning the two (2) holes in the blade

with the raised lugs on the adapter.

• Be sure the trailing edge of blade

(opposite sharp edge) is up toward the

engine.

• Install the blade bolt with the lock

washer and hardened washer into blade

adapter and crankshaft.

• Use block of wood between blade and

lawn mower housing and tighten the

blade bolt, turning clockwise.

• The recommended tightening torque is

35-40 ft. Ibs.

TO SHARPEN BLADE

NOTE: We do not recommend sharpening

blade - but if you do, be sure the blade is

balanced.

Care should be taken to keep the blade

balanced. An unbalanced blade will cause

eventual damage to lawn mower or

engine.

•The blade can be sharpened with a file

or on a grinding wheel. Do not attempt

to sharpen while on the mower.

• To check blade balance, drive a nail into

a beam or wall. Leave about one inch of

the straight nail exposed. Place center

hole of blade over the head of the nail.

If blade is balanced, it should remain in

a horizontal position. If either end of the

blade moves downward, sharpen the

heavy end until the blade is balanced.

IMPORTANT: Blade bolt is grade 8 heat

treated.

Blade

adapter

Key _

Blade _"

Blade

bolt

Crankshaft

keyway

washer Hardened Blade

washer Trailing adapter

edge

GRASS CATCHER

•The grass catcher may be hosed with

water, but must be dry when used.

•Check your grass catcher often for

damage or deterioration. Through

normal use it will wear. If catcher needs

replacing, replace only with a manufac-

turer approved replacement catcher.

Give the lawn mower model number

when ordering.

ENGINE

LUBRICATION

Use onlyhigh qualitydetergent oil ratedwith

API service class'_cationSF, SG or SH.

Select the oil's8AE viscositygrade according

to your expected operating temperature.

"F , "20" ,O" , _" _ '_ ,IO" • _* . 10_,

._ _ -lr 6- 1o, _ _ J*_ I_TURE _ ANTICIPATEDBEFORENEXT OtLCR'tNGE

NOTE: Although multJ-viscosily oils (5W30,

10W30 etc.) improve starting in cold weather,

these multi-viscosityoils will result in increased

oilconsumption when used above 32°F.

Check your engine oil level more frequently to

avoid possible engine damage from running

low on oil.

Change the oil after every 25 hours of

operation or at least once a year ifthe

lawn mower is not used for 25 hours in

one year.

Check the crankcase oil level before starting

the engine and after each five(5) hours of

continuous use. l'_jhten oil plug securely each

time you check the oil level.

TO CHANGE ENGINE OIL

• Disconnect spark plug wire from spark

plug and place wire where it cannot

come in contact with spark plug.

•Be sure lawn mower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove bottom oil drain plug.

•After oil has drained completely, replace

oildrain plug and tighten securely.

•Refill engine with oil. Pour slowly. Do

not over fill.

•Fill to top of slot inside of filler hole.

•Reconnect spark plug wire to spark

plug.

Drain plug

AIR FILTER

Your engine will not run properly and may

be damaged by using a dirty air fitter.

Replace the air filter every year, more

often if you mow in very dusty, dirty

conditions. Do not wash air filter.

TO CHANGE AIR FILTER

• Remove the air filter by turning counter-

clockwise to the stop and pull away from

collar.

•Remove filter from inside of cover.

Inhaltsverzeichnis

Andere Craftsman Rasenmäher Handbücher

Craftsman

Craftsman 917.374031 Bedienungsanleitung

Craftsman

Craftsman 247.25001 Bedienungsanleitung

Craftsman

Craftsman 917.28857 Bedienungsanleitung

Craftsman

Craftsman 917.379202 Bedienungsanleitung

Craftsman

Craftsman 25O43 Bedienungsanleitung

Craftsman

Craftsman 917.275821 Bedienungsanleitung

Craftsman

Craftsman 247.203702 Bedienungsanleitung

Craftsman

Craftsman 917.377592 Bedienungsanleitung

Craftsman

Craftsman 247.889210 Bedienungsanleitung

Craftsman

Craftsman 917.27632 Bedienungsanleitung

Craftsman

Craftsman 3One 917.373680 Bedienungsanleitung

Craftsman

Craftsman 917.387601 Bedienungsanleitung

Craftsman

Craftsman 38872 Bedienungsanleitung

Craftsman

Craftsman 247.397900 Bedienungsanleitung

Craftsman

Craftsman 917.376802 Bedienungsanleitung

Craftsman

Craftsman 917.373491 Bedienungsanleitung

Craftsman

Craftsman 25968 Bedienungsanleitung

Craftsman

Craftsman 247.375910 Bedienungsanleitung

Craftsman

Craftsman 247.288842 Bedienungsanleitung

Craftsman

Craftsman 917.370432 Bedienungsanleitung

Craftsman

Craftsman 917.370941 Bedienungsanleitung

Craftsman

Craftsman 37640 Bedienungsanleitung

Craftsman

Craftsman 917.28705 Bedienungsanleitung

Craftsman

Craftsman 917.370940 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung