Craftsman 315.223400 Bedienungsanleitung

PERATOR'S

T$ MAN AL

STAND-n-STOW" CABINET WITH LEG STAND

Model No.

315.223400

_ WARNING: To reduce the risk of injury,

the user must read and understand the

operator's manual before using this product.

Customer Help Line: 1-800-932-3188

Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA

Visit the Craftsman web page: www.sears.com/craftsman

987000-214

12-04-07 (REV:01) Save this manual for future reference

AWARNING: Read and understand all instructions.

Failure to follow all instructions listed below may

result in electric shock, fire, and/or serious personal

injury.

Safe operation of this accessory requires that you read

and understand this operator's manual, the operator's

manual for the miter saw, and all labels affixed to the tool.

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS

•KNOW YOUR ACCESSORY. Read the operator's

manual carefully, Learn the applications and limitations

as well as the specific potential hazards related to this

tool.

ASSEMBLING THE STAND-n-STOW TM CABINET

See Figure 1.

This product requires assembly,

• Insert the supplied lock nut into the hex nut pocket,

• Align the reinforcement plate holes with the tab on the

bottom of the base and the screw hole in the base.

• Place supplied washer and lock washer onto the

supplied screw,

• Insert screw into the hole in the base.

• Turn clockwise to tighten screw,

• Repeat above steps until all four screws have

been inserted and tightened into base and both

reinforcement plates are installed.

HEXNUT BASE

POCKET

o Q

WASHER

REINFORCEMENT

PLATE LOCKWASHER

-_SCREW

Fig. 1

MOUNTING THE STAND-n-STOW TM CABINET

BASE TO THE LEG STAND

See Figures 2 -4.

When the leg stand and Stand-n-Stow TM cabinet are not in

use, the leg stand can be folded up and placed in the leg

stand storage area as indicated in figure 4.

• Place the leg stand on the floor then open the leg

stand by pushing opposite legs in opposite directions

as indicated by the arrows in figure 2.

Place the Stand-n-Stow TM cabinet on the leg stand.

Align the slots in the miter saw base with the slots on

the top of the leg stand,

• Insert the tab on the Stand-n-Stow TM cabinet locking

knob into the slot on the leg stand.

• Turn the locking knob clockwise to secure the Stand-n-

Stow TM cabinet to the leg stand,

• Repeat with the other three locking knobs.

Fig. 2

STAND-N-STOWTM

CABINET LOCKING

KNOBS

SLOTS HEXBOLT MOUNTING

HOLES

LOCK

WASHER

Fig. 3

LEGSTAND

STORAGEAREA

Fig. 4

TO MOUNT MITER SAW

See Figure 5.

•Insert the supplied 3/8 in. machine bolts through the

holes in the miter saw base. Each of the four mounting

holes should be bolted through the miter saw base

securely using supplied 3/8 in. machine bolts, lock

washers, and hex nuts as shown in figure 5.

• Tighten all four bolts securely.

MITER WASHER HEXNUT

SAWBASE Fig. 5

MAKING A MOUNTING BOARD

When mounting a saw other than the 212340, 212380, or

the 212010, create a mounting board (at least 3/4 in. thick

plywood) to secure the miter saw to the leg stand.

To pre drill holes:

• With a pencil, mark holes on the mounting board where

it will bolt to the Stand-n-Stow TM cabinet.

• Drill holes large enough to fit 3/8 in. machine bolts

through both the mounting board and Stand-n-Stow TM

cabinet.

To mount miter saw to mounting board:

• Insert the 3/8 in. machine bolts through the holes in

the miter saw base. Each of the four mounting holes

should be bolted through the mounting board and

through the miter saw base securely using 3/8 in. ma-

chine bolts, lock washers, and hex nuts (not included).

Bolts should be of sufficient length to accommodate

the miter saw base, lock washers, and the hex nuts.

• Tighten all four bolts securely.

Once the miter saw has been bolted to the mounting

board, attach the mounting board and miter saw assem-

bly to the Stand-n-Stow TM cabinet according to the steps

as noted in the previous section, Mounting the Stand=n-

Stow TM Cabinet Base to the Leg Stand.

," CRAFTSMAN LEG STAND - 315.223400 -_

The model number will be found on a plate attached to the miter saw base. Always mention the model |number in all correspondence regarding your LEG STAND or when ordering repair parts. J

SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS

Key

No. Part

Number

1 000999007900

2 000999007008

3 000999007702

4 411061001

5 000999007005

6 000999007012

7 000999007011

8 000999007013

9 000999007002

10 411101702

11 0101040201

12 000999007007

13 412011067

14 000999007006

15 412011009

16 412021002

17 000999007001

18 000999007901

19 000999007700

PARTS LIST

Description Qty.

Warning Label ................................................................................... 1

Logo Label ........................................................................................ 1

Stand-n-Stow TM Cabinet Assembly ................................................... 2

*Lock Nut (M6) ................................................................................... 4

Reinforcement Plate ......................................................................... 2

Lock Washer (M6) ............................................................................. 4

Washer .............................................................................................. 4

*Screw (M6 x 25 mm) ......................................................................... 4

Knob ................................................................................................. 4

*Push Nut (5/16 in.) ............................................................................ 4

Pad ................................................................................................... 4

Bungee Cord .................................................................................... 2

Washer (M8 x 18 x 15t) ..................................................................... 4

*Lock Nut (M10) ................................................................................. 4

*Washer (D10.5 x D20 x 1.6t) ............................................................. 8

*Lock Washer (M10) ........................................................................... 4

*Hex Bolt (M10 x 75 mm) ................................................................... 4

Data Plate ......................................................................................... 1

Stand-n-Stow TM Base Assembly (Includes Key Nos. 1-18) ............... 1

* Standard Hardware Item - May Be Purchased Locally

CRAFTSMAN LEG STAND - 315.223400

I The model number will be found on a plate attached to the miter saw base. Always mention the model |

number in all correspondence regarding your LEG STAND or when ordering repair parts. J

SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS

* Standard Hardware Item - May Be Purchased Locally

CRAFTSMAN LEG STAND - 315.223400 =*

l The model number will be found on a plate attached to the miter saw base. Always mention the model |

number in all correspondence regarding your LEG STAND or when ordering repair parts, iJ

SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS

Key Part

No. Number

1 000999007009

2 0121010312-126

3 411071003

4 0121010205

5 0121010213

6 410191003

7 0121010228

8 0121010804

9 0121010305-126

10 410031012

11 0121010212

12 0131010918

13 410451016

14 0121010311-126

15 0121010226

000999007701

987000214

Description Qty.

Connector Bracket ........................................................................... 4

Leg Tube ........................................................................................... 3

Nylon Nut (M5) ................................................................................ 20

Leg Adaptor ...................................................................................... 4

End Plug ........................................................................................... 3

Screw (M4 x 12 mm) ......................................................................... 1

Ring .................................................................................................. 1

Screw .............................................................................................. 20

Linkage ............................................................................................. 8

Carriage Bolt (M12 x 75 mm) ............................................................ 1

Front Level Adjusting Knob .............................................................. 1

Spring ............................................................................................... 1

Screw, Pan Hd. (M6 x 10 mm) .......................................................... 4

Leg Tube ........................................................................................... 1

Linkage Ring ..................................................................................... 4

Leg Stand Assembly Incl. 1-15)

Operator's Manual

* Standard Hardware Item - May Be Purchased Locally

Andere Craftsman Rack & Stand Handbücher

Craftsman

Craftsman 320.16491 Bedienungsanleitung

Craftsman

Craftsman 351.241300 Bedienungsanleitung

Craftsman

Craftsman 320.16490 Bedienungsanleitung

Craftsman

Craftsman 695.22302 Bedienungsanleitung

Craftsman

Craftsman 320.16488 Bedienungsanleitung

Craftsman

Craftsman CMXMSAJ94773 Bedienungsanleitung

Craftsman

Craftsman 22283A Bedienungsanleitung

Craftsman

Craftsman 320.16492 Bedienungsanleitung

Craftsman

Craftsman 130.16491 Bedienungsanleitung

Craftsman

Craftsman 50159 - 3 Bedienungsanleitung

Craftsman

Craftsman 320.22305 Bedienungsanleitung

Craftsman

Craftsman 714.58688 Bedienungsanleitung

Craftsman

Craftsman 320.19730 Bedienungsanleitung

Craftsman

Craftsman CMXMSAJ94772 Bedienungsanleitung

Craftsman

Craftsman 351.220200 Bedienungsanleitung

Craftsman

Craftsman 922210 Bedienungsanleitung

Craftsman

Craftsman Versatrack Bedienungsanleitung

Craftsman

Craftsman 320.22335 Bedienungsanleitung

Craftsman

Craftsman CMXMSAJ094788 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung