Craftsman 22299 Bedienungsanleitung

Owner's Manual

[ I

I,CR"FTS"nNI!

Folding Miter Saw Stand

Stock No. 22200

HTC Products

•Safety

•Assembly

•Operation

• Parts

CAUTION:

Before using this product, read this manual and follow

all its Safety Rules and Operating Instructions.

SEARS, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman Website: www.sears.com/craftsman

Congratulations

You have just purchased a 22299 Folding Miter Saw Stand. This product has been specifically designed to assist you

in the use of your 10-12" miter saw.

Parts 44 TT

Figure, 4"_ 4

_Snap Button RightLeg(rear)_

(_ _LeftLeg(front)

ModelNumber

ATopFrame

B StraightLegs

C CurvedLegs

DOutriggerSupports

ESupport"T"

F MTGHookR/L

GClampBracketR/L

H WheelMountRight

I WheelMountLeft

J 6" Wheels

K AluminumExtrusion

L Multi-Stop

5/16"-18 x 2 W' T-BOLT

t,.l"_

-- 5/16" FLAT WASHER

L- 5/16"-18 MULTI-STOP BOI.T

22299 ffl'Y

5096 1

2901 2

2900 2

5099 2

5098 2

2898R/L 1/1

2906R/L 1/1

2897 R 1

2897 L 1

H213 2

2896 2

2890 1

C227 4

C204 8

2343 1

ModelNumber 22299 QTY

¢_" Leg Plugs(right) 2908R 2

_. Leg Plugs(left) 2908L 2

_. 5/16" LockWashers C226 4

_" 5/16" HexNut C202 4

---r- 1/4"- 20 x 5/8" HexBolts D122 12

u... 1/4"- 20 NylokNut D102 8

"4 1/4" - 20 x 1-3/4" HexBolt D139 4

",N 5/16" - 18 x 1/2" 3-PointKnob G101 5

5/16" - 18 x 1-1/2" 3-PointKnob G103 2

"!" ThreadedPlate 2902 1

__ LatchPin(wheelaxles) F206 2

#=_,.-4SnapButton F103 4

X_' 1/4"- 20 SerratedFlangeNut Dl18 8

¢_.-_ 1/4"- 20 CarriageBolt D138 4

General Safety Instructions for

Power Tools

Using power tools of any kind can be dangerous if safe operating procedures

are not followed. Recognizing the hazards of each tool and using them with

respect and caution will considerably limit the possibility of personal injury.

However, if safety precautions are ignored, personal injury will likely result.

Always use common sense - your personal safety is your responsibility.

1. Know your power tool. Read and understand the Owner's Manual and

observe the warnings and instruction labels affixed to the tool.

2. Properly ground all tools.

3. Keep guards in place.

4. Remove adjusting keys and wrenches.

5. Keep work area clean and dry.

6. Keep children away.

7. Never leave running machines/tools unattended,

8. Disconnect tools from service.

9. Use correct tools for the job.

10. Never force a tool.

22299 Hardware List Update

Please update lt'4"-20x5/8" he× bolt

(_)122) quanity to 8 (originally 12).

I_ew part (4 only) 1/4-20x5/8" carriage

.bolt (D213) is for u$e When attaching

v#heel "e{xle brackets to the frame in

step 3.

11. Wear safety apparel.

12. Wear safety glasses/goggles.

13. Never stand or sit on tools.

14. Replace damaged components immediately.

15. Make sure your work platform is sufficiently sturdy to do the specific job

at hand.

16. Properly anchor power tools to work stands.

17. Use correct blade for job being done.

18. Think Safety. Safety is a combination of operator awareness, common

sense and alertness at all times.

Safety Instructions for

Miter Saw Stands

1. Use caution when folding or unfolding legs to limit any finger pinch points.

2. Place stand on flat and level surface to keep tool from rocking or tipping.

3. Make certain that work support extensions are within safe operating limits,

and are properly locked in place before using tool. De not exceed 500 Ibs.

on main frame table.

4. Test the setup for stability before proceeding with work.

5. Be sure the miter saw is tightened securely at all mountings before use or

folding the stand for transport.

_Weld Nut

Figure 2

Figure 3

Assembly Instructions

Read all assembly instructions completely before attempting assembly.

See parts list on Page 2 for names and pictures of parts. Figure 1.

1. identify all components and hardware.

2. Place top frame upside down on your workbench or work surface. Position

so that the nuts welded to the top of the frame tubes will be positioned in

the lower right and upper left when the frame is turned over for assembly.

Figure 2.

3. Attach the wheel axle brackets to the left end of the frame. Note you will have

a right and left bracket. When the mounting holes are aligned, the correct

_bracket will position the axle parallel to the work surface. Secure with 1/4"- 20

_X5/8" hex bolts from the inside of the frame, 1/4"- 20 Nylok nuts on the

outside of the frame. Figure 2.

NOTE: For easy movement with the stand fully opened, attach the wheers to

the outside of the lower legs as shown in Figure 3. If you choose this position,

complete this portion of the assembly as your last step.

Use (2) 1/4"-20 x 1-3/4" hex bolts and (2)1/4"-20 Nylok nuts per leg.

Figure 4

Figure 5

Figure 6

Install snap buttons intothe top end of the straight legs. Carefully guide the

snap buttons into position with a screw driver until it pops into the large

through hole in the top of the legs.Straight legs will be installedon the left

end of the frame. Figure 4.

Installsnap buttons into the top of the curved legs. These will be oriented as

left and right (front/back) during assembly. Curved top legs will be attached to

the right end of the frame. Figure 1 shows the correct installation of the snap

buttons and correct right/left orientation.

Attach the straight legs to the frame using (1) 1/4"- 20 x 2" carriage bolt,

(1) 5/16" flat washer and (1) 1/4"- 20 Nylok nut per leg. Bolt will pass

through the flat washer, then through the left hole in the frame plate closest

to the frame tube, through the top hole in the leg and through the bracket

on the inside of the frame. Secure with 1/4"- 20 Nylok nut. Figure 5.

Repeat this procedure for the leg directly opposite (back).

NOTE: Tighten the leg fasteners so the legs are stiff when folding or opening

the stand.

7, Attach the left curved legs to the frame using (1) 1/4"- 20 x 2" carriage bolt,

(1) 5/16" flat washer and (1) 1/4"- 20 Nylok nut per leg. Use the hole which is

second from the right, closest to the frame tube to attach the leg. Pass the

bolt through the flat washer, then through the hole in the outside of the frame,

through the top hole in the leg, through the bracket on the inside of the frame,

and secure with 1/4"- 20 Nylok nut. Figure 6 and 7.

Repeat this procedure for the right (back) leg.

8. Install 1-1/4" angled tube plugs into the bottom of all four legs. Plug angle will

match the leg angle to allow the stand to sit flush on the floor.

Figure 7

9, Rotate both the right and left legs to be sure the spring plugs engage the

holes in the frame plate in the extended and collapsed position. Fold the left

legs down. Fold the right legs down. Be sure the right legs nest neatly over

the left legs and lock in position for transport.

10. Return legs to extended positions. Carefully stand the assembly upright on

the floor. Figure 8

11. Thread 5/16"- 18 x 1/2" 3-point knobs into the weld nuts on the top of

the frame tube. Install the outrigger support and secure in place with the

3-point knob.

12. Thread 5/16"- 18 x 1/2" 3-point knobs into the outrigger ends. Install

support T's as shown, secure with 3-point knob. Figure 8.

13. Carefully review Figures 9, 10 and 11. Both the mounting hook and the

clamp bracket are Right/Left specific. Begin by sliding (4) 1/4"-20 x 5/8"

hex bolts into the small "T" slot on each aluminum extrusion.

14. Attach the mounting hook and clamp bracket to the extrusion using the

1/4"-20 hex bolts installed in Step 15 and (4) 1/4"-20 serrated flange nuts

per extrusion. Thread 5/16"-18 x 1-1/2", 3-point knobs onto the clamp

brackets as shown. Hand tighten only.

15. Slide (4) T-bolts into the large (top) slot on the aluminum extrusion. Space

them to the approximate distance required to mount the saw. Figure 11.

16. Carefully lift the saw up and place onto the aluminum extrusion, passing

the T-mounting bolts installed in Step 15 through the mounting holes in the

base of the miter saw. Figure 12.

1; L

"_'!L 11]

Figure 11

17. Secure the saw in place on the aluminum extrusion with (1) 5/16" flat

washer, (1) 5/16" lock washer, and (1) 5/16" hex nut per T-mounting bolt.

Hand tighten only.

Figure 12

Figure 13

Figure 14

18,

19.

20.

21.

Carefully lift the saw with the attached extrusions and place onto the

leg/frame assembly, Adjust the saw front/back along the extrusion to balance

the saw on the frame. The mounting hook and clamp angle can also be

adjusted to further balance the saw, and to equally space the mounting

brackets along the extrusion.

Slide the mounting hook and clamp angle under the table top tube as

shown in Figure 13. Tighten all the bracket fasteners and the saw mounting

fasteners. The saw and extrusions can now be secured to the stand by

tightening the 5/16"-18 x 1-1/2", 3-point knobs installed in Step 14.

Install the multi-stop onto right or left support T. Attach the multi-stop to

the T with special shoulder bolt, passed through the round hole in the

multi-stop, through the round hole in the support T and into the threaded

mounting plate positioned on the inside of the T. Align the mounting plate

with an adjacent hole in the support T and install a 5/16"-18 x 1/2" 3-point

knob to hold the multi-stop in place. Figure 14 and 15.

The multi-stop can be used on the right or left support T. It may also be

positioned anywhere along the length of the T. Use as a bump stop for

repetitive cuts or as a fence style stop for squaring material to the blade.

Install the wheels onto the axle brackets with the integrated spacer facing

towards the center of the stand. Secure with the latch pin, passed through the

hole in the axle bracket. Figure 16.

Figure 15

Figure 16

Set-up /Knockdown

Procedure

1. Be sure the saw is positioned to the extreme left on the frame and securely

tightened.

2. Starting with the legs at the wheel end (left), depress the snap buttons to

release the legs.

3. Carefully walk the frame and saw down to the floor while allowing the legs

to fold under. Once resting on the floor, the legs can be completely folded

to engage the snap buttons. Figure 17.

Carefully stand the unit up onto the wheeled end.

5. Depress the snap buttons on the remaining 2 legs. Fold the legs down until

they nest neatly under the frame and the snap buttons engage the frame.

Figure 18.

The stand is now ready to roll. Reverse the procedure to set the stand up

for use. Figure 19.

Figure 17

Figure 18

Figure 19

Get it fixed, atyour home or ours!

Your Home

For repair-in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME ® (1-800-469-4663)

Call anytime, day or night (U.S.A, and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Center.

1-800-488-1222

Call anytime, day or night (U.S.A. only)

www.sears.com

To purchase a protection agreement (U.S.A.)

or maintenance agreement (Canada) on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada

Para pedir servicio de reparacion

a domicilio, y para ordenar piezas:

1-888-SU-HOGAR s_

(1-888-784-6427)

Au Canada pour service en fran£a_s:

1-800-LE-FOYER "c

(1-800-533-6937)

www.sears.ca

® Registered Trademark /TMTrademark /_ Service Mark of Sears, Roebuck and Co.

TM SM

® Marea Registrada /Marca de Fabriea /Marea de Servicio de Sears, Roebuck and Co,

MCMarque de commerce /MDMarque deposee de Sears, Roebuck and Co. © Sears, Roebuck and Co.

Inhaltsverzeichnis

Andere Craftsman Gesehen Handbücher

Craftsman

Craftsman RADIAL ARM SAW 315.22038 Bedienungsanleitung

Craftsman

Craftsman 137.218300 Bedienungsanleitung

Craftsman

Craftsman 113 Bedienungsanleitung

Craftsman

Craftsman 172.26043 Bedienungsanleitung

Craftsman

Craftsman 103.21041 Gebrauchs- und Pflegehandbuch

Craftsman

Craftsman 21221 - 12 in. Sliding Dual Bevel Compound Miter... Bedienungsanleitung

Craftsman

Craftsman 113.221611 Bedienungsanleitung

Craftsman

Craftsman 137.218020 Bedienungsanleitung

Craftsman

Craftsman 103.24260 Gebrauchs- und Pflegehandbuch

Craftsman

Craftsman 315.115790 Bedienungsanleitung

Craftsman

Craftsman 137.216000 Bedienungsanleitung

Craftsman

Craftsman 351.221140 Bedienungsanleitung

Craftsman

Craftsman 315.21449 Bedienungsanleitung

Craftsman

Craftsman 133.33166 Bedienungsanleitung

Craftsman

Craftsman evolv 320.31024 Bedienungsanleitung

Craftsman

Craftsman 315.212120 Bedienungsanleitung

Craftsman

Craftsman 137.224140 Bedienungsanleitung

Craftsman

Craftsman 315.212040 Bedienungsanleitung

Craftsman

Craftsman 113.24201 Bedienungsanleitung

Craftsman

Craftsman MiterMate 137.212260 Bedienungsanleitung

Craftsman

Craftsman 113.19771 Bedienungsanleitung

Craftsman

Craftsman 286.17589 Bedienungsanleitung

Craftsman

Craftsman 137.24885 Bedienungsanleitung

Craftsman

Craftsman nextec 320.61325 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung